• Foundation
  • About 15 min
  • 5 practice questions

Uses of electricity, safety, electric cells and batteries

Group the uses of electricity, follow the safety rules for experiments, identify the terminals of an electric cell and explain how cells are joined to make a battery.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Group the many uses of electricity and state the safety rules for experiments.
  • Identify the positive and negative terminals of an electric cell.
  • Explain how two or more cells are joined to make a battery and why.

Switch off every electrical device at home for one evening and you would quickly see how much we depend on electricity: no lights, fans, mixer, mobile charging or television. Electricity reaches our homes through wires from power stations that use falling water, wind, sunlight, coal or gas. In this chapter we learn how electricity is made to do useful work, starting with something small and safe: a torch.

Uses of electricity

Uses of electricity

  • Lighting
    • Homes, offices, streets, markets
  • Cooking
    • Electric kettle, mixer grinder, toaster, oven
  • Heating and cooling
    • Fan, geyser, room heater, refrigerator, air conditioner
  • Communication and entertainment
    • Mobile phone, internet, radio, television
  • Transport
    • Electric trains, lifts, escalators, electric scooters
  • Other work
    • Water pumps, cranes, computers, hospital machines
One way of grouping; you can group the same uses in other ways too

Safety first

Never experiment with the electricity supply from wall sockets or generators. Use only cells or batteries, like those in torches, clocks and remotes, for experiments.

The danger signs on electric poles and transformers are there for a reason: the mains supply can cause severe injury or even death. Cells used in torches and remotes give a much smaller, safe supply, which is why all the activities in this chapter use them.

The electric cell

An electric cell is a portable source of electrical energy. Look closely at one and you will see two ends, called terminals. The end with a small metal cap sticking out is the positive terminal (+). The end with a flat metal disc is the negative terminal (−). The + and − signs are usually printed on the cell too.

Terminals of a common torch cell
PartWhat it looks likeName
One endSmall metal cap that sticks outPositive terminal (+)
Other endFlat metal discNegative terminal (−)

Joining cells to make a battery

A torch often uses two or more cells. If you put them in the wrong way round, the torch does not light. It lights only when the positive terminal of one cell touches the negative terminal of the next. A combination of two or more cells joined like this is called a battery. Connecting more cells gives the circuit more energy and/or lets it work for longer. In everyday speech, people also call a single cell, such as the one in a mobile phone, a 'battery'.

Cells joined to make a battery

  1. Cell 1 Its + terminal touches the − terminal of cell 2.
  2. Cell 2 Its + terminal touches the − terminal of cell 3.
  3. Cell 3 The free + of the last cell and the free − of the first cell are the battery's terminals.

In some devices, such as a TV remote, cells sit side by side. Look inside the compartment: a metal strip joins the + of one cell to the − of the next, and the + and − marks printed inside show which way each cell should go.

Worked example 1: will the torch light?

A torch holds two cells in a tube. Riya puts them in like this: (a) cap of the first cell touching the flat disc of the second; (b) the flat discs of both cells touching each other. Working: in (a), + of one touches − of the next, so the cells form a proper battery and the torch can light. In (b), − touches −, so the cells oppose each other and the torch will not light. The rule: + to −, every time.

Worked example 2: finding the battery's terminals

Two cells sit in a holder, each with its negative terminal towards the spring. Which end of the holder is positive? Working: the holder end connected to the free metal cap of one cell is the positive terminal of the battery; the end connected to the free flat disc of the other cell is the negative terminal. Following the caps and discs always gives the answer, even if the printed signs have worn off.

Key takeaways: electricity is used for lighting, cooking, heating and cooling, communication, transport and much more. Experiment only with cells and batteries, never with the mains. A cell has a positive terminal (metal cap) and a negative terminal (flat disc). Cells joined + to − make a battery, which gives more energy or works for longer.

Check your understanding

  1. 1. Which source of electricity is safe for school experiments?

    1. A wall socket at home
    2. A torch cell
    3. A portable generator
    4. An electric pole
    Show answer

    Answer: B. Only cells and batteries like those in torches, clocks and remotes are safe for experiments. Mains sockets, generators and poles can cause severe injury.

  2. 2. On a torch cell, the small metal cap that sticks out is the:

    1. Negative terminal
    2. Switch
    3. Filament
    4. Positive terminal
    Show answer

    Answer: D. The protruding metal cap is the positive (+) terminal; the flat metal disc is the negative (−) terminal.

  3. 3. What is a battery?

    1. Two or more cells joined with the + of one to the − of the next
    2. A single wire joined to a lamp
    3. Two cells joined − to −
    4. A switch with two terminals
    Show answer

    Answer: A. A battery is a combination of two or more cells connected positive terminal to negative terminal.

  4. 4. A torch uses two cells. Which arrangement will make it light?

    1. Flat disc touching flat disc
    2. Cap touching cap
    3. Cap of the first cell touching the flat disc of the second
    4. Either cell removed
    Show answer

    Answer: C. The cells must be joined + to −, so the metal cap (+) of one touches the flat disc (−) of the next.

  5. 5. Why are two or more cells often used together in a device?

    1. To stop the device from working
    2. Because one cell has no terminals
    3. To give more energy and/or let the device work for a longer time
    4. To make the device lighter
    Show answer

    Answer: C. Connecting more cells provides more energy to the circuit, or provides it for longer.

Privacy · Terms · Refunds · Delivery