Revision notes

States of Matter: Foundation

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Solids, liquids and gases: the particle picture

Comparing the three states
PropertySolidLiquidGas
ShapeFixedTakes shape of containerTakes shape of container
VolumeFixedFixedNot fixed; fills container
Particle spacingVery smallSmallVery large
Force between particlesStrongestModerateVery weak
CompressibilityAlmost noneVery smallHigh
DensityUsually highestUsually lower than solidVery low

Solid: fixed shape and fixed volume. Liquid: fixed volume, no fixed shape. Gas: neither fixed shape nor fixed volume.

— Remember
  • Matter is anything with mass that occupies space.
  • Particle spacing and attraction decide the state.
  • Solids keep shape and volume; liquids keep volume only; gases keep neither.
  • Gases are highly compressible; solids and liquids are not.
Read the full lesson

Lesson 2

Changes of state and latent heat

Changes of state
ChangeNameHeat
Solid to liquidMelting (fusion)Absorbed
Liquid to solidFreezing (solidification)Released
Liquid to gasBoiling / vaporisationAbsorbed
Gas to liquidCondensationReleased
Solid to gas directlySublimationAbsorbed
Gas to solid directlyDepositionReleased

During a change of state the temperature stays constant; the heat supplied goes into latent heat. Q = m × L.

— Remember
  • Melting, boiling and sublimation absorb heat; freezing, condensation and deposition release it.
  • K = °C + 273.
  • Latent heat changes state without changing temperature.
  • Steam burns more than boiling water because of latent heat.
Read the full lesson

Lesson 3

Pressure, temperature and volume of gases

Boyle: P₁V₁ = P₂V₂ (constant T). Charles: V₁/T₁ = V₂/T₂ (constant P, T in kelvin).

— Remember
  • Boyle's law: pressure and volume are inversely proportional at constant temperature.
  • Charles's law: volume is proportional to kelvin temperature at constant pressure.
  • Always convert °C to K before using Charles's law.
Read the full lesson

Lesson 4

Evaporation, boiling and diffusion

Evaporation compared with boiling
FeatureEvaporationBoiling
TemperatureAny temperatureOnly at the boiling point
Where it happensSurface onlyThroughout the liquid (bubbles)
SpeedSlowFast
CoolingCauses coolingHeat must be supplied

Evaporation: surface, any temperature, causes cooling. Boiling: whole liquid, fixed temperature.

— Remember
  • Evaporation is a surface process at any temperature and causes cooling.
  • Boiling happens throughout the liquid at the boiling point.
  • Diffusion is the mixing of particles by their own motion and is fastest in gases.
Read the full lesson

Lesson 5

Beyond three states: plasma, BEC and mixed practice

  • Plasma is an ionised gas with free electrons and ions.
  • BEC forms near absolute zero from a very low density gas.
  • Practise Boyle and Charles problems with correct units, and remember the traps above.
Read the full lesson

Lesson 6

Density of solids, liquids and gases: mass, volume and floating

Density in the three states
StateParticle spacingTypical density
SolidVery smallHigh (for example, metals)
LiquidSmallModerate
GasVery largeVery low

Density = mass ÷ volume. Float if the object's density is less than the liquid's; sink if it is greater. 1 g/cm³ = 1000 kg/m³.

  • Density measures how much mass is packed into a given volume.
  • Solids are usually densest, then liquids, then gases, which are far less dense.
  • Ice is less dense than liquid water and floats.
  • Compare densities to decide floating and sinking; keep units consistent.
Read the full lesson

Lesson 7

The heating curve of water: temperature rises and flat sections with heat calculations

Sloping part: Q = m c ΔT. Flat part: Q = m L and the temperature does not change. Add the stages in order.

  • A flat part of a heating curve shows a change of state; the heat goes into latent heat.
  • Use Q = m c ΔT when the temperature changes and Q = m L when the state changes.
  • The boiling stage needs far more heat than the melting stage.
  • Work through the curve stage by stage and add the results.
Read the full lesson

Lesson 8

Gas pressure: units, atmospheric pressure and the mercury barometer

Pressure units
UnitSymbolValue
Standard atmosphereatm1 atm = 101,325 Pa
Millimetre of mercurymm Hg760 mm Hg = 1 atm
Barbar1 bar = 100,000 Pa (slightly less than 1 atm)
PascalPa1 Pa = 1 N/m²
KilopascalkPa1 kPa = 1000 Pa

Pressure = force ÷ area. 1 atm = 760 mm Hg = 101,325 Pa. Convert before you substitute; keep the same unit on both sides of a ratio.

  • Pressure is force per unit area; its SI unit is the pascal.
  • Gas pressure comes from the collisions of particles with the walls.
  • A mercury barometer balances air pressure against a column about 760 mm high.
  • 1 atm = 760 mm Hg = 101,325 Pa.
Read the full lesson

Lesson 9

Avogadro's law and the mole of a gas: volume, mass and number of molecules

Conversions at STP
QuantityFormula at STP
Moles from volumen = V (in litres) ÷ 22.4
Volume from molesV = n × 22.4 litres
Moles from massn = mass ÷ molar mass
Number of moleculesN = n × 6.022 × 10²³
Density of a gasd = molar mass ÷ 22.4 g/L

At STP, 1 mol of any gas = 22.4 L = molar mass in grams = 6.022 × 10²³ molecules. Equal volumes of gases at the same T and P have equal numbers of molecules.

  • Avogadro's law: equal volumes, same T and P, same number of molecules.
  • At STP, one mole of any gas occupies 22.4 L.
  • Convert mass to moles, then moles to volume or molecules.
  • Use 22.4 L/mol only when the conditions are STP.
Read the full lesson

Privacy · Terms · Refunds · Delivery