Revision notes

States of Matter: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Particle model and changes of state: exam problems

Solid, liquid and gas compared
PropertySolidLiquidGas
Spacing of particlesVery closeCloseVery far apart
Intermolecular forceStrongestModerateNegligible
MovementVibrate about fixed positionsSlide past each otherMove freely and randomly
ShapeFixedTakes shape of containerTakes shape of container
VolumeFixedFixedFills the container
CompressibilityAlmost noneVery littleHigh

During a change of state the temperature of a pure substance stays constant; heat supplied changes the arrangement of particles, not their average speed.

Key takeaways: Learn the table of properties, remember that temperature is flat during a change of state, and never confuse evaporation (surface, any temperature, cooling) with boiling (whole liquid, fixed temperature).

Read the full lesson

Lesson 2

Boyle's and Charles's laws: solving gas problems

Kelvin = degrees Celsius + 273. Never put a Celsius value into Charles's law.

Key takeaways: Boyle is inverse (P times V constant), Charles is direct (V over T constant), and kelvin is compulsory. Always sanity-check the direction of change.

Read the full lesson

Lesson 3

Ideal gas equation and molar volume problems

At STP: moles = volume in litres / 22.4. In any other condition use PV = nRT.

Key takeaways: Choose between combined law, PV = nRT and 22.4 L per mole depending on what is given, keep temperature in kelvin, and check units of R.

Read the full lesson

Lesson 4

Dalton's law of partial pressures and Graham's law of diffusion

Partial pressure = mole fraction x total pressure. Rate of diffusion is proportional to 1 / square root of molar mass.

Key takeaways: Use mole fractions for Dalton, remember lighter means faster for Graham, and subtract water vapour pressure when a gas is collected over water.

Read the full lesson

Lesson 5

Liquids and solids: vapour pressure, viscosity and crystal types

Four classes of crystalline solid
TypeParticlesBinding forceExampleTypical behaviour
IonicPositive and negative ionsElectrostatic attractionSodium chlorideHard, brittle, high melting point, conducts when molten or dissolved
MolecularMoleculesWeak intermolecular forcesIce, iodineSoft, low melting point, poor conductor
Covalent (network)AtomsCovalent bonds throughoutDiamond, silicaVery hard, very high melting point
MetallicMetal ions in sea of electronsMetallic bondCopper, ironConducts, malleable, ductile

A liquid boils when its vapour pressure equals the external pressure.

Key takeaways: Boiling means vapour pressure equals external pressure; stronger forces mean lower vapour pressure and higher viscosity and surface tension; solids are classified by the particles and forces that hold them.

Read the full lesson

Lesson 6

Gas problems with changing amounts: connected flasks, leaks and used cylinders

Four patterns
PatternWhat is conservedFormula
Joined flasksTotal molesP = (P1V1 + P2V2) ÷ (V1 + V2)
Open vessel heatedVolume fixed, moles falln2 ÷ n1 = T1 ÷ T2
Cylinder refilling vesselsTotal PV at fixed T(P1V1 − P_final V1) ÷ (P V of vessel)
Gas used from cylinderFixed V and TFraction used = (P1 − P2) ÷ P1

When the amount of gas changes, track PV (at constant T) or PV ÷ T. Do not apply Boyle's or Charles's law to the whole system unless the amount is fixed.

  • At constant T, n ∝ PV; add PV values to combine gases.
  • A heated open rigid vessel loses gas in proportion to 1 − T1/T2.
  • A cylinder cannot be emptied below the pressure of the outside; subtract the gas that remains.
  • With fixed V and T, the fraction of gas used equals the fall in pressure divided by the original pressure.
Read the full lesson

Lesson 7

Graham's law question types: rates, times, volumes in equal time and distances

Graham's law
Given or askedFormula
Rates r1, r2r1 ÷ r2 = √(M2 ÷ M1)
Times t1, t2 for the same volumet1 ÷ t2 = √(M1 ÷ M2)
Volumes V1, V2 in the same timeV1 ÷ V2 = √(M2 ÷ M1)
Densities d1, d2r1 ÷ r2 = √(d2 ÷ d1)
Distances x1, x2 in a tubex1 ÷ x2 = √(M2 ÷ M1)

Rate ∝ 1/√M. Time ∝ √M. For a rate ratio put the heavier mass on top, then take the square root; to find M, square the ratio.

  • Identify the form: rate, time, equal-time volume, density or distance.
  • Lighter gas: faster, shorter time, further distance.
  • Solve for M by squaring the ratio.
  • The meeting point of two gases is nearer the end of the heavier gas.
Read the full lesson

Lesson 8

Liquids: comparing boiling point, vapour pressure, viscosity and capillary rise

Boiling point comparisons
ComparisonHigher boiling pointReason
Neon, argon, kryptonKryptonMore electrons, stronger London forces
Water, H2SWaterHydrogen bonding
Ethanol, dimethyl ether (both C2H6O)EthanolHydrogen bonds between –OH groups
n-Pentane, neopentane (both C5H12)n-PentaneLarger surface area of contact
HF, HClHFHydrogen bonding

Find the strongest force first: hydrogen bond > dipole-dipole > London (for similar sizes). Stronger forces: higher boiling point, viscosity and surface tension; lower vapour pressure. Capillary rise ∝ 1/radius.

  • Compare hydrogen bonding first, then size and shape.
  • Stronger forces mean lower vapour pressure and higher boiling point.
  • Viscosity and surface tension both fall as temperature rises.
  • Capillary rise is inversely proportional to the radius; mercury is depressed.
Read the full lesson

Lesson 9

Mixed revision: statement, assertion-reason and multi-step questions on states of matter

Test each statement on its own against a single known fact. In assertion-reason items, decide A, then R, then whether R explains A.

  • Absolute words in a statement are a warning sign.
  • In an assertion-reason item, a true reason may still fail to explain the assertion.
  • Chain two laws by writing V2 = V1 × (P1/P2) × (T2/T1) and checking each factor's direction.
  • Revise the traps list before an exam.
Read the full lesson

Privacy · Terms · Refunds · Delivery