Revision notes

Chapter 5 Heat: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Latent heat: melting and boiling at constant temperature

Heating ice to steam

  1. Ice + water at 0 °C (flat part) Heat is absorbed but the temperature stays at 0 °C until all the ice melts.
  2. Water warms from 0 °C to 100 °C (rising part) The heat now raises the temperature of the water.
  3. Boiling water + steam at 100 °C (flat part) Heat is absorbed but the temperature stays at 100 °C until all the water becomes steam.
Flat parts of the graph show a change of state at constant temperature.

Specific latent heat = heat absorbed at constant temperature by unit mass during a change of state. Heat needed Q = m × L. For water: L(fusion) = 80 cal/g (about 333 kJ/kg); L(vaporisation) = 540 cal/g (about 2256 kJ/kg).

Approximate values for some substances
SubstanceMelting point (°C)Boiling point (°C)
Water0100
Ethyl alcohol-11778
Lead327.51749
Copper10832562

Key takeaways: during melting and boiling, heat is absorbed without a rise in temperature; it is used to weaken or break the bonds between molecules. Q = mL. For water, latent heat of fusion is 80 cal/g and of vaporisation 540 cal/g. The same heat is released on freezing and condensing.

Read the full lesson

Lesson 2

Regelation and the anomalous behaviour of water

Water has its minimum volume and maximum density at 4 °C. Cooling water below 4 °C makes it expand, not contract.

What happens in Hope's apparatus

  1. Water at the middle is cooled Above 4 °C, colder water is denser, so it sinks.
  2. T₁ (bottom) falls quickly to 4 °C T₂ (top) falls only slowly. T₁ then stays at about 4 °C.
  3. Water cooled below 4 °C becomes lighter It expands, its density falls, and it rises to the top.
  4. T₂ (top) falls quickly to 0 °C The top reaches 0 °C first; T₁ reaches 0 °C later.
The two temperature curves cross at the temperature of maximum density, 4 °C.

Key takeaways: pressure lowers the melting point of ice, so ice melts under pressure and refreezes when it is removed (regelation). Water contracts from 0 °C to 4 °C and is densest at 4 °C. Hope's apparatus shows this. This behaviour keeps aquatic life alive under ice and makes freezing water burst pipes and crack rocks.

Read the full lesson

Lesson 3

Humidity, saturated air and dew point

Relative humidity (%) = (actual mass of water vapour in a given volume of air ÷ mass of vapour needed to saturate that volume at the same temperature) × 100. At the dew point, relative humidity is 100%.

Everyday signs of water vapour

  • Cold bottle from the refrigerator
    • Air touching the bottle cools below its dew point
    • Vapour condenses as droplets on the outside
  • Dew in the early morning
    • Grass, leaves and car windows cool at night
    • Vapour in the air near them condenses into drops
  • White trail behind an aircraft
    • Vapour from the engine condenses into a cloud-like trail
    • In humid air the trail lasts long
    • In dry air it is short or does not form

Key takeaways: air can hold only a limited amount of vapour, which depends on temperature. The dew point is the temperature at which unsaturated air becomes saturated on cooling. Absolute humidity is vapour mass per unit volume (kg/m³); relative humidity compares actual vapour with the saturating amount, and is 100% at the dew point.

Read the full lesson

Lesson 4

Units of heat and specific heat capacity

Specific heat capacity (c): the heat needed to raise the temperature of unit mass of a substance by 1 °C. Heat gained or lost Q = m × c × ΔT. Units: J/kg °C (SI), cal/g °C (CGS).

Approximate specific heat capacities
Substancec (cal/g °C)
Water1.0
Aluminium0.215
Iron0.11
Copper0.095
Silver0.056
Mercury0.033

Key takeaways: 1 cal is the heat that warms 1 g of water by 1 °C (14.5 °C to 15.5 °C); 1 kcal = 1000 cal; 1 cal ≈ 4.18 J. Specific heat capacity is the heat per unit mass per °C; Q = m c ΔT. Water's high specific heat makes it heat and cool slowly.

Read the full lesson

Lesson 5

Principle of heat exchange and calorimetry

Principle of heat exchange: heat lost by the hot object = heat gained by the cold object (when no heat is exchanged with the surroundings).

Balancing the heat

  • Heat lost (Q)
    • By the hot solid
    • Q = m(solid) × c(solid) × (fall in its temperature)
  • Heat gained (Q₁ + Q₂)
    • By the water: Q₁ = m(water) × c(water) × (rise)
    • By the calorimeter: Q₂ = m(cal) × c(cal) × (rise)
Q = Q₁ + Q₂. If the specific heats of water and calorimeter are known, that of the solid can be found.

Key takeaways: heat lost by hot bodies equals heat gained by cold bodies when no heat escapes. In the mixing method, heat lost by the solid equals heat gained by water plus calorimeter. Combine Q = mcΔT and Q = mL when ice melts or steam condenses.

Read the full lesson

Privacy · Terms · Refunds · Delivery