Revision notes

Chapter 4 Constructions of Triangles: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Getting ready: earlier constructions and the idea behind the new ones

Perpendicular bisector with compass

  1. Draw the segment Seg XY = 6 cm.
  2. Arcs from X Radius more than half of XY.
  3. Arcs from Y Same radius; mark crossings P and Q.
  4. Join P and Q Line PQ ⊥ XY through its midpoint.

New constructions in this chapter: find two lines on which the missing vertex must lie, and take their point of intersection. A point equidistant from C and D lies on the perpendicular bisector of seg CD.

Key takeaways: three suitable parts fix a triangle. The perpendicular bisector of a segment contains exactly the points equidistant from its ends, and you can draw it with two pairs of equal arcs. A point that lies on two lines is their intersection. Always draw and label a rough figure, then write numbered steps, then draw the fair figure.

Read the full lesson

Lesson 2

Construction I: base, a base angle and the sum of the other two sides

Construction I at a glance

  1. Base BC Draw the given base.
  2. Ray at B At the given angle ∠B.
  3. Mark D BD = AB + AC on the ray.
  4. Join DC This segment is the key.
  5. Bisect DC Perpendicular bisector cuts the ray at A.
  6. Join AC Triangle complete.

Construction I: mark BD = AB + AC on the ray at B; A is where the perpendicular bisector of seg DC meets ray BD, because AD = AC.

Key takeaways: lay the sum of the two sides along the ray at the given angle, join the far end to the other end of the base, and bisect that segment perpendicularly. The vertex is where the bisector meets the ray. If ∠C is given, work from C; if the perimeter is given, subtract the base first. The sum must exceed the base.

Read the full lesson

Lesson 3

Construction II (case 1): the side at the given angle is the longer one

Construction II, case AB − AC

  1. Base BC Draw it.
  2. Ray BL at ∠B Given angle at B.
  3. Mark D on ray BL BD = AB − AC (short length).
  4. Join DC Then bisect it perpendicularly.
  5. Bisector meets ray at A Because AD = AC.
  6. Join AC Triangle complete.
Case 1: the side at the given angle is longer
GivenLonger sideWhere D goesBisect
BC, ∠B, AB − ACAB (at ∠B)On ray BA, BD = AB − ACSeg DC
BC, ∠C, AC − ABAC (at ∠C)On ray CA, CD = AC − ABSeg DB

Case 1 (side at the given angle is longer): mark the difference on the ray at the given angle itself; the vertex is where the perpendicular bisector of the segment joining D to the other end of the base meets that ray.

Key takeaways: when the longer side is next to the given angle, D lies on that same ray, between the vertex of the angle and A. Because AD equals the shorter side, A is on the perpendicular bisector of seg DC. The difference must be smaller than the base.

Read the full lesson

Lesson 4

Construction II (case 2): the side at the given angle is the shorter one

Construction II, case AC − AB

  1. Base BC Draw it.
  2. Ray BT at ∠B Given angle at B.
  3. Opposite ray BS Extend the ray through B.
  4. Mark D on ray BS BD = AC − AB.
  5. Bisect DC Perpendicular bisector meets ray BT at A.
  6. Join AC AD = AC, so the triangle is correct.

The two cases of Construction II (angle at B)

  • Case 1: AB − AC given
    • AB is longer
    • D on ray BA
    • BD = AB − AC
    • AD = AB − BD = AC
  • Case 2: AC − AB given
    • AB is shorter
    • D on the opposite ray of BA
    • BD = AC − AB
    • AD = AB + BD = AC

Case 2 (side at the given angle is shorter): mark the difference on the OPPOSITE ray at the given angle; the vertex is where the perpendicular bisector of seg DC meets the ray at the given angle.

Key takeaways: when the side next to the given angle is the shorter one, D goes on the opposite ray, below the base. Then AD = AB + BD equals the longer side AC, so A is on the perpendicular bisector of DC. Decide the case from which side is longer, and keep the difference less than the base.

Read the full lesson

Lesson 5

Construction III: perimeter and the two base angles

Construction III at a glance

  1. Draw PQ = perimeter The three sides laid end to end.
  2. Half angles at P and Q ½∠B at P, ½∠C at Q.
  3. Rays meet at A Vertex of the triangle.
  4. Bisect AP and AQ They cut PQ at B and C.
  5. Join AB and AC Triangle complete.
Summary of the chapter's constructions
ConstructionGivenKey step
IBase, ∠B, AB + ACBD = AB + AC on ray at B; bisect DC
II, case 1Base, ∠B, AB − ACBD = AB − AC on ray at B; bisect DC
II, case 2Base, ∠B, AC − ABBD = AC − AB on opposite ray; bisect DC
IIIPerimeter, ∠B, ∠CPQ = perimeter, half angles at P and Q; bisect AP and AQ

Construction III: draw PQ = perimeter, angles ½∠B at P and ½∠C at Q meeting at A; the perpendicular bisectors of AP and AQ cut PQ at B and C.

Key takeaways: the perimeter becomes one straight segment PQ. Because PB = BA, the angle at P is half of ∠B (exterior angle theorem), and likewise at Q. B and C are found on the perpendicular bisectors of AP and AQ. With a ratio of sides, divide the perimeter into parts and construct from three sides.

Read the full lesson

Privacy · Terms · Refunds · Delivery