Revision notes

Electricity: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Electric charge, Coulomb's law and electric field

F = kq₁q₂/r², E = F/q = kq/r². Force on charge q in a field: F = qE. k = 9 × 10⁹ N m²/C², e = 1.6 × 10⁻¹⁹ C.

— Remember
  • Coulomb's force follows an inverse-square law.
  • Convert μC and nC to coulombs before substituting.
  • The field direction is that of the force on a positive test charge.
Read the full lesson

Lesson 2

Potential, potential difference and capacitors

V = W/q. C = Q/V. Parallel: C adds. Series: 1/C adds. U = ½CV². 1 eV = 1.6 × 10⁻¹⁹ J.

— Remember
  • Capacitors behave opposite to resistors: parallel adds, series uses reciprocals.
  • Energy in a capacitor is ½CV².
  • A volt is a joule per coulomb.
Read the full lesson

Lesson 3

Current, Ohm's law and resistance

V = IR. R = ρL/A. Stretching a wire to n times its length multiplies R by n². Parallel resistance is always less than the smallest branch.

— Remember
  • Resistance rises with length and falls with area.
  • Series: same current, voltages add. Parallel: same voltage, currents add.
  • Convert mm² to m² for R = ρL/A.
Read the full lesson

Lesson 4

Circuits, EMF and Kirchhoff's rules

I = E/(R + r). V = E − Ir. Junction rule: ΣI in = ΣI out. Loop rule: ΣΔV = 0. Balanced bridge: P/Q = R/S.

— Remember
  • Terminal voltage is below the EMF whenever current is drawn.
  • Reduce series-parallel networks step by step.
  • In a balanced bridge no current flows in the middle arm.
Read the full lesson

Lesson 5

Heating effect of current and electrical power

P = VI = I²R = V²/R. H = I²Rt. 1 kWh = 3.6 × 10⁶ J. In series, the larger resistance dissipates more power; in parallel, the smaller resistance does.

— Remember
  • Choose P = V²/R when voltage is fixed and I²R when current is fixed.
  • Cost = kWh × rate per unit.
  • Power is proportional to V² for a fixed resistance.
Read the full lesson

Lesson 6

Capacitor networks: charge, voltage and energy sharing

Series and parallel compared
PropertySeriesParallel
ChargeSame on eachShared in ratio of C
VoltageShared in inverse ratio of CSame across each
Equivalent CSmaller than the smallestLarger than the largest
Energy storedLarger on the smaller CLarger on the larger C
Dielectric of constant K inserted
QuantityBattery connected (V fixed)Battery removed (Q fixed)
CapacitanceK timesK times
ChargeK timesSame
VoltageSame1/K times
EnergyK times1/K times

Series: same Q, voltages divide inversely to C. Parallel: same V, charges divide in proportion to C. Joined capacitors share charge, not energy.

— Rule to remember
  • Find the equivalent capacitance first, then the charge, then work back to each capacitor.
  • In series the smaller capacitor carries the larger voltage.
  • After joining charged capacitors use V = (Q1 + Q2)/(C1 + C2).
  • With a dielectric, ask first: battery connected or removed?
Read the full lesson

Lesson 7

Resistor networks: balance, symmetry and cutting tricks

Equal potential, no current: remove it. Shorted resistor: remove it. Wire cut into n pieces and joined in parallel: R/n². Bigger current through smaller resistance.

— Rule to remember
  • Redraw the circuit with the junctions marked by letters before you reduce it.
  • Look for balanced bridges, symmetry and shorts first.
  • Treat a ring as two parallel arcs.
  • Check any answer by confirming the voltages across parallel branches are equal.
Read the full lesson

Lesson 8

Combining cells and the maximum power condition

Grouping n identical cells
GroupingNet EMFNet internal resistance
SeriesnEnr
ParallelEr/n

Series: E and r multiply by n. Parallel: E unchanged, r divides by n. Maximum power to the load when R = r, and P_max = E²/4r.

— Rule to remember
  • Find E_net and r_net first, then use I = E_net/(R + r_net).
  • Series suits large loads, parallel suits small ones.
  • A cell being charged has terminal voltage E + Ir.
  • Maximum power needs R = r and gives only 50 percent efficiency.
Read the full lesson

Lesson 9

Drift velocity, resistivity and the effect of temperature

I = nAev. R = ρL/A, but ρ depends only on material and temperature. Stretch to n times the length: R becomes n² times. R = R₀(1 + αΔT) for a metal.

— Rule to remember
  • Drift velocity is tiny, but the signal travels almost instantly.
  • Resistivity is a property of the material, resistance is a property of the piece.
  • Stretching a wire at constant volume multiplies R by the square of the length ratio.
  • Metals get more resistive when hot.
Read the full lesson

Privacy · Terms · Refunds · Delivery