- Practice
- About 13 min
- 5 practice questions
Drift velocity, resistivity and the effect of temperature
Use I = nAev to find how slowly electrons drift, separate resistance from resistivity, and solve stretching and temperature problems.
If something looks wrong, please tell us.
Switch on a lamp and it lights at once, yet the electrons in the wire move very slowly. This lesson explains that apparent puzzle with the idea of drift velocity, then uses resistivity and temperature coefficients to solve the numerical problems that follow. Values are for practice only.
Drift velocity and current
Free electrons in a metal move randomly at high speed, colliding with ions. When a field is applied, each electron picks up a very small average velocity along the wire, called the drift velocity v. If a wire has n free electrons per cubic metre, cross-section A and each carries charge e, then the current is I = n A e v. The lamp lights at once because the electric field sets up in the whole wire almost instantly, so electrons everywhere begin to drift together.
Worked example 1: how slow is the drift?
Suppose a copper wire has A = 2 × 10⁻⁶ m² (2 mm²) and n = 8.5 × 10²⁸ per m³ (a typical textbook value, used here for practice). It carries 5 A. Then v = I/(nAe) = 5/(8.5 × 10²⁸ × 2 × 10⁻⁶ × 1.6 × 10⁻¹⁹). The denominator is 2.72 × 10⁴, so v = 5/27 200 = 1.84 × 10⁻⁴ m/s, about 0.18 mm every second. Doubling the current doubles v, and a thinner wire carrying the same current needs a larger v.
Resistance and resistivity
Resistance R = ρL/A belongs to a particular piece of wire. Resistivity ρ belongs to the material (and its temperature): it does not change if you cut the wire or change its thickness. So the resistance of a wire depends on length, area, material and temperature, while its resistivity depends only on material and temperature.
Worked example 2: comparing two wires
Two wires of the same material have lengths in the ratio 1 : 2 and radii in the ratio 2 : 1. Area is proportional to radius squared, so the areas are in the ratio 4 : 1. Then R ∝ L/A gives R1 : R2 = (1/4) : (2/1) = 1 : 8.
Stretching a wire
When a wire is stretched, the volume stays the same, so area A falls as length L rises: A ∝ 1/L. Since R ∝ L/A, R ∝ L². A wire pulled to 3 times its length has 9 times the resistance. For a small stretch of x percent, the resistance rises by about 2x percent.
Worked example 3: stretching
A wire of 4 Ω is drawn out to 3 times its length. New R = 4 × 3² = 36 Ω. If a 10 Ω wire is lengthened by 1 percent, its length becomes 1.01 of the original and R becomes 10 × (1.01)² = 10.2 Ω, close to the 2 percent estimate.
Temperature effects
For a metal, resistance rises with temperature: R = R₀(1 + αΔT), where α is the temperature coefficient of resistance. In semiconductors and insulators the resistance falls as temperature rises, since more charge carriers become free.
Worked example 4: a hot filament
A metal coil has R₀ = 100 Ω at 0 °C and α = 4 × 10⁻³ per °C (made-up values). At 50 °C, R = 100 × (1 + 0.004 × 50) = 100 × 1.2 = 120 Ω. This is why a lamp draws a large current at the instant it is switched on: its cold filament has low resistance.
I = nAev. R = ρL/A, but ρ depends only on material and temperature. Stretch to n times the length: R becomes n² times. R = R₀(1 + αΔT) for a metal.
Key takeaways
- Drift velocity is tiny, but the signal travels almost instantly.
- Resistivity is a property of the material, resistance is a property of the piece.
- Stretching a wire at constant volume multiplies R by the square of the length ratio.
- Metals get more resistive when hot.
Check your understanding
-
1. The diameter of a wire is doubled, with length and material unchanged. Its resistance becomes:
- double
- four times
- one quarter
- half
Show answer
Answer: C. Area becomes 4 times, so R = ρL/A becomes one quarter.
-
2. If the current in a wire is doubled, the drift velocity of the electrons becomes:
- doubled
- unchanged
- halved
- four times
Show answer
Answer: A. I = nAev, so with n, A and e unchanged, v is proportional to I and doubles.
-
3. A metal coil has R₀ = 50 Ω at 0 °C and α = 0.004 per °C. At 100 °C its resistance is:
- 50.4 Ω
- 90 Ω
- 20 Ω
- 70 Ω
Show answer
Answer: D. R = 50 × (1 + 0.004 × 100) = 50 × 1.4 = 70 Ω.
-
4. A wire of resistance 4 Ω is stretched to three times its length (volume constant). Its new resistance is:
- 12 Ω
- 36 Ω
- 4/3 Ω
- 16 Ω
Show answer
Answer: B. R ∝ L², so R = 4 × 9 = 36 Ω.
-
5. Which quantity does NOT change when a copper wire is cut in half?
- Resistance
- Length
- Resistivity
- Area times length
Show answer
Answer: C. Resistivity is a property of the material at a given temperature, so cutting does not change it. Resistance and length both halve, and area times length (the volume) also halves.
Sign in to keep track of the lessons you finish.