• Practice
  • About 14 min
  • 5 practice questions

Combining cells and the maximum power condition

Work out the current when cells are joined in series, parallel or opposition, and find the load that receives the most power.

If something looks wrong, please tell us.

One cell often cannot give the voltage or the current a job needs, so cells are grouped. The question is then how the group behaves: what is its EMF, what is its internal resistance, and which grouping suits a given load? The numbers here are made up for practice.

Series and parallel groups of identical cells

Take n identical cells, each of EMF E and internal resistance r. In series (positive of one to negative of the next) the EMFs add and so do the internal resistances: E_net = nE, r_net = nr. In parallel (all positives together, all negatives together) the EMF stays E but the internal resistances share the current: r_net = r/n. In every case the current in a load R is I = E_net/(R + r_net).

Grouping n identical cells
GroupingNet EMFNet internal resistance
SeriesnEnr
ParallelEr/n

Worked example 1: series

Three cells, each of EMF 1.5 V and internal resistance 0.5 Ω, are joined in series to a 3.5 Ω resistor. E_net = 4.5 V and r_net = 1.5 Ω, so I = 4.5/(3.5 + 1.5) = 0.9 A. The terminal voltage is E − Ir = 4.5 − 0.9 × 1.5 = 3.15 V, which equals IR = 0.9 × 3.5 = 3.15 V.

Worked example 2: parallel

The same three cells in parallel give E_net = 1.5 V and r_net = 0.5/3 = 1/6 Ω. For the 3.5 Ω resistor, I = 1.5/(3.5 + 1/6) = about 0.41 A, much less than 0.9 A. For a small load of 0.5 Ω, however, the parallel group gives I = 1.5/(0.5 + 1/6) = 2.25 A, and the series group gives 4.5/(0.5 + 1.5) = 2.25 A too. The two groupings give the same current exactly when R equals the internal resistance of one cell (here 0.5 Ω). For a larger load the series grouping is better, and for a smaller load the parallel grouping is better.

Cells in opposition and cells being charged

If two cells face each other in a loop, the net EMF is the difference. A 10 V cell and a 4 V cell opposed, with internal resistances of 1 Ω each and a 4 Ω resistor, give I = (10 − 4)/(1 + 1 + 4) = 1 A, driven by the stronger cell. The weaker cell is being charged, and its terminal voltage is greater than its EMF: V = E + Ir. For a 4 V cell with r = 1 Ω charged by a current of 2 A, V = 4 + 2 × 1 = 6 V.

Maximum power transfer

The power delivered to a load R is P = I²R = E²R/(R + r)². Plotting P against R shows a single peak at R = r. At that point P_max = E²/4r. Half of the total power is wasted in the cell itself, so the efficiency at maximum power is only 50 percent. Power stations never work at this condition, but signal sources often do.

Worked example 3: maximum power

A source has E = 12 V and r = 3 Ω. Maximum power goes to R = 3 Ω. Then I = 12/(3 + 3) = 2 A and P = I²R = 4 × 3 = 12 W. Check with the formula: E²/4r = 144/12 = 12 W. For R = 6 Ω, I = 12/9 = 1.33 A and P = 1.78 × 6 = 10.7 W, which is less.

Series: E and r multiply by n. Parallel: E unchanged, r divides by n. Maximum power to the load when R = r, and P_max = E²/4r.

— Rule to remember

Key takeaways

  • Find E_net and r_net first, then use I = E_net/(R + r_net).
  • Series suits large loads, parallel suits small ones.
  • A cell being charged has terminal voltage E + Ir.
  • Maximum power needs R = r and gives only 50 percent efficiency.

Check your understanding

  1. 1. Four cells of 1.5 V each are joined in series. The net EMF is:

    1. 1.5 V
    2. 3 V
    3. 6 V
    4. 0.375 V
    Show answer

    Answer: C. In series the EMFs add: 4 × 1.5 = 6 V.

  2. 2. Four identical cells, each with internal resistance 2 Ω, are joined in parallel. The net internal resistance is:

    1. 8 Ω
    2. 0.5 Ω
    3. 1 Ω
    4. 2.0 Ω
    Show answer

    Answer: B. In parallel r_net = r/n = 2/4 = 0.5 Ω.

  3. 3. A cell of EMF 9 V and internal resistance 1.5 Ω supplies a load. The maximum power that can be delivered to the load is:

    1. 13.5 W
    2. 6.75 W
    3. 27 W
    4. 54 W
    Show answer

    Answer: A. The best load is R = 1.5 Ω. P_max = E²/4r = 81/6 = 13.5 W.

  4. 4. A cell of EMF 6 V and internal resistance 1 Ω is being charged with a current of 2 A. Its terminal voltage is:

    1. 4 V
    2. 6 V
    3. 7 V
    4. 8 V
    Show answer

    Answer: D. While charging, V = E + Ir = 6 + 2 × 1 = 8 V, which is above its EMF.

  5. 5. When a source delivers maximum power to its load, the efficiency of the circuit is:

    1. 50 percent
    2. 100 percent
    3. 25 percent
    4. 75 percent
    Show answer

    Answer: A. At R = r the load and the internal resistance get equal power, so half the power reaches the load: 50 percent.

Privacy · Terms · Refunds · Delivery