- Practice
- About 20 min
- 5 practice questions
System, surroundings, properties and thermodynamic processes
Define system, surroundings and boundary, classify open, closed and isolated systems, tell extensive from intensive properties and state from path functions, and recognise reversible, irreversible, adiabatic, isothermal, isobaric, isochoric and cyclic processes.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define system, surroundings and boundary and classify a system as open, closed or isolated.
- Sort properties into extensive and intensive.
- Tell a state function from a path function.
- Name the condition that defines each type of thermodynamic process.
Burning fuel, a battery driving current and the body digesting food all turn one form of energy into another. Thermodynamics (Greek thermos, heat, and dynamics, flow) studies these energy changes in quantitative terms. It grew out of efforts in the nineteenth century to make steam engines more efficient. It deals with bulk (macroscopic) properties such as heat and work, and does not depend on any theory of molecular structure. It can tell whether a change is possible under given conditions, but not how fast it will happen: rates belong to chemical kinetics.
System, surroundings and boundary
The system is the part of the universe we are studying: water in a beaker, air in a balloon, a glucose solution. Everything else is the surroundings. They are separated by a real or imaginary boundary. A system is homogeneous if all its parts are in the same physical state (a mixture of gases, two fully miscible liquids) and heterogeneous if not (oil and water).
Three types of system
-
Open system
- Exchanges matter and energy
- Example: hot water in an open beaker
- Living things are open systems
-
Closed system
- Exchanges energy only, not matter
- Boundary sealed but not insulated
- Example: hot water in a stoppered flask; gas in a cylinder with a piston
-
Isolated system
- Exchanges neither matter nor energy
- Boundary sealed and insulated
- Example: hot water in a closed vacuum (thermos) flask (approximately)
Extensive and intensive properties
| Extensive (depends on the amount) | Intensive (does not depend on the amount) |
|---|---|
| Mass, volume, number of moles | Density, molar volume, molar mass |
| Internal energy, enthalpy | Temperature, pressure |
| Entropy, free energy | Boiling point, freezing point, refractive index, surface tension |
| Heat capacity | Specific heat capacity, molarity, molality, mole fraction |
A quick test: imagine cutting the system in half. An extensive property halves; an intensive one stays the same. The ratio of two extensive properties is intensive: mass ÷ volume = density, volume ÷ moles = molar volume.
Thermodynamic processes
A process is any operation that changes the state of a system: heating, cooling, expansion, compression, melting or boiling. A reversible process goes in infinitesimally small steps, with system and surroundings in equilibrium at every stage, so it can be reversed exactly and leave no change in the universe. An irreversible process happens in a finite time, out of equilibrium, and cannot be undone without leaving a change; every natural process is irreversible.
| Process | What is constant | Condition | Example |
|---|---|---|---|
| Adiabatic | No heat exchanged | q = 0 | Gas expanding in an insulated cylinder |
| Isothermal | Temperature | dT = 0 | Reaction in a thermostat |
| Isobaric | Pressure | dP = 0 | Reaction in an open beaker |
| Isochoric | Volume | dV = 0 | Combustion in a sealed bomb calorimeter |
| Cyclic | System returns to its initial state | dU = 0, dH = 0, dP = 0, dV = 0, dT = 0 | Working fluid of an engine over one cycle |
In an adiabatic process the system cannot take in heat, so if it does work its temperature falls, and if work is done on it its temperature rises (a bicycle pump gets warm).
State functions and path functions
A state function has a definite value for each state of the system, whatever route brought the system there: P, V, T, internal energy U, enthalpy H, entropy S and free energy G. Its change depends only on the initial and final states. A path function depends on the route taken: heat q and work w. Climbing a hill is a good picture: your change in height (state function) is the same by any path, but the distance you walk (path function) is not.
State functions (U, H, S, G, P, V, T): change depends only on initial and final states; zero for a complete cycle. Path functions (q, w): depend on how the change is carried out.
Worked example 1: classifying properties
Classify: (a) 2 mol of water, (b) the density of that water, (c) its enthalpy, (d) its molar enthalpy. Working: (a) number of moles depends on amount: extensive. (b) density = mass/volume, a ratio of two extensive properties: intensive. (c) enthalpy doubles if the amount doubles: extensive. (d) molar enthalpy = H/n, again a ratio: intensive.
Worked example 2: identifying processes
A gas in a cylinder is compressed, heated, allowed to expand and finally cooled so that P, V and T are back to their starting values. Working: because the system returns exactly to its initial state, this is a cyclic process, so ΔU = 0 and ΔH = 0 for the whole cycle, even though heat and work were exchanged at each step. Heat and work need not be zero, because they are path functions.
Key takeaways: open systems exchange matter and energy, closed systems energy only, isolated systems neither. Extensive properties depend on amount, intensive ones do not. U, H, S, G are state functions; q and w are path functions. Know the condition for each process: q = 0, dT = 0, dP = 0, dV = 0, or a return to the start.
Check your understanding
-
1. Hot coffee in a sealed, well-insulated vacuum flask is best described as
- an open system
- a closed system
- an isolated system
- a heterogeneous open system
Show answer
Answer: C. The sealed lid stops matter (vapour) escaping and the insulation stops heat leaving, so neither matter nor energy is exchanged (to a good approximation): an isolated system.
-
2. Which of these is an intensive property?
- Enthalpy
- Heat capacity
- Volume
- Molar volume
Show answer
Answer: D. Molar volume is volume divided by moles, a ratio of two extensive quantities, so it does not change with the amount. Enthalpy, heat capacity and volume all double when the amount doubles.
-
3. Which pair contains only path functions?
- Heat and work
- Internal energy and enthalpy
- Entropy and heat
- Pressure and work
Show answer
Answer: A. Heat and work depend on how a change is carried out (for example reversibly or irreversibly). U, H, S and P are state functions.
-
4. Fuel is burnt in a sealed steel bomb. Which kind of process is this?
- Isobaric
- Isothermal
- Adiabatic
- Isochoric
Show answer
Answer: D. The strong sealed bomb cannot change its volume, so dV = 0: the combustion is isochoric. That is why a bomb calorimeter measures the heat at constant volume.
-
5. For an ideal gas taken through a complete cycle, which statement is correct?
- q = 0 and w = 0
- ΔU = 0, but q and w need not be zero
- ΔU = q
- ΔH is positive
Show answer
Answer: B. After a full cycle the system is back in its initial state, so every state function, including U and H, has zero change. Heat and work are path functions and can be non-zero; from ΔU = q + w, q = −w for the cycle.
Sign in to keep track of the lessons you finish.