• Practice
  • About 20 min
  • 5 practice questions

Work done by a constant force and by a variable force

Define work as the scalar product of force and displacement, decide when work is positive, negative or zero, and calculate the work done by constant and variable forces.

If something looks wrong, please tell us.

By the end of this lesson you can

  • State the physics meaning of work and write W = F⃗ · dr⃗ = F dr cos θ.
  • Give the SI unit (joule) and dimensional formula [ML²T⁻²] of work.
  • Use the angle θ to decide whether work is positive, negative, maximum or zero.
  • Find the work done by a constant force as (F cos θ)(r_f − r_i).
  • Find the work done by a variable force as an integral, and as the area under a force-displacement graph.

In daily life we call almost any effort 'work': reading, carrying a bag, even thinking hard. Unit 4 of the Tamil Nadu textbook gives the word a precise physics meaning. Work is done only when a force acts on a body and the body is displaced. Doing work needs energy, and the rate of doing work is power, so these three quantities (work, energy and power) are studied together in this unit.

Work as a scalar product

Let a force F⃗ act on a body while the body undergoes a small displacement dr⃗. The work done by the force is defined as the scalar (dot) product W = F⃗ · dr⃗. Using the rule a⃗ · b⃗ = ab cos θ, this becomes W = F dr cos θ, where θ is the angle between the force and the displacement. Only the component of force along the displacement, F cos θ, does work.

Because a dot product of two vectors is a scalar, work is a scalar: it has magnitude but no direction. Its SI unit is the newton metre (N m), called the joule (J). One joule is the work done when a force of 1 N moves a body through 1 m along the direction of the force. The dimensional formula of work is [ML²T⁻²].

W = F⃗ · dr⃗ = F dr cos θ. Unit: joule (1 J = 1 N m). Dimensions: [ML²T⁻²].

When is work positive, negative or zero?

For a given force and displacement, the value of cos θ decides the nature of the work.

How the angle between force and displacement decides the work
Angle θcos θWork done
θ = 0°1Positive and maximum (F dr)
0° < θ < 90°between 0 and 1Positive
θ = 90°0Zero
90° < θ < 180°between −1 and 0Negative
θ = 180°−1Negative and maximum in size (−F dr)

Work is zero in three situations: (i) no force acts (F = 0), as for an ideal puck gliding on perfectly frictionless ice; (ii) there is no displacement (dr = 0), as when you push hard against a fixed wall; (iii) the force is perpendicular to the displacement (θ = 90°). In case (iii), gravity does no work on a trolley pushed along a level floor, and the centripetal force does no work on a body moving in a circle, because it always points along the radius while the displacement is along the tangent.

Work is negative when the force opposes the motion. When a cyclist applies the brakes, the friction force on the wheels points backwards while the bicycle moves forwards, so friction does negative work and the bicycle slows down. When a fielder catches a fast ball, the force from the hands opposes the ball's motion, so the hands do negative work on the ball.

Nature of the work done by a force

  • Positive work (0° ≤ θ < 90°)
    • Force has a component along the motion
    • Example: gravity on a falling stone
  • Zero work
    • No force, or no displacement
    • Or force ⟂ displacement (θ = 90°)
    • Example: centripetal force
  • Negative work (90° < θ ≤ 180°)
    • Force has a component against the motion
    • Example: friction on a sliding box

Work done by a constant force

If the force is constant in size and direction, the small work done for a small displacement dr is dW = (F cos θ) dr. Adding (integrating) from the initial position r_i to the final position r_f gives W = ∫ (F cos θ) dr = (F cos θ)(r_f − r_i), because F cos θ comes out of the integral. On a graph of F cos θ against r, a constant force is a horizontal line, and the work done is the area of the rectangle under it between r_i and r_f.

Work done by a variable force

When the force changes with position (a spring force is an example), we cannot simply multiply. We divide the displacement into tiny steps dr, in each of which the force is nearly constant, find dW = (F cos θ) dr for each, and add them all up: W = ∫ from r_i to r_f of F cos θ dr. Graphically, the work done is the area under the curve of F cos θ against r between r_i and r_f.

Worked example 1: pulling a trolley at an angle

A girl pulls a luggage trolley with a force of 40 N along a handle that makes 60° with the floor. The trolley moves 12 m along the floor. Step 1: F = 40 N, dr = 12 m, θ = 60°, cos 60° = 0.5. Step 2: W = F dr cos θ = 40 × 12 × 0.5 = 240 J. Only the horizontal component 40 × 0.5 = 20 N does work; the vertical component is perpendicular to the motion.

Worked example 2: sliding down a smooth slope

A 2 kg block slides 8 m down a frictionless slope inclined at 30° to the horizontal (take g = 9.8 m s⁻²). Find the work done by gravity and by the normal force. Step 1: resolve gravity: the component along the slope is mg sin θ = 2 × 9.8 × 0.5 = 9.8 N, in the direction of motion. Step 2: W_gravity = 9.8 × 8 × cos 0° = 78.4 J. Check: the block drops through a height h = 8 sin 30° = 4 m, and mgh = 2 × 9.8 × 4 = 78.4 J, the same. Step 3: the normal force and mg cos θ are perpendicular to the slope, so each does zero work.

Worked example 3: a ball thrown up and caught

A 0.5 kg ball is thrown straight up, rises 3.0 m and falls back to the thrower's hand (g = 9.8 m s⁻², no air resistance). Going up: gravity is downward, displacement upward, θ = 180°: W_up = 0.5 × 9.8 × 3.0 × (−1) = −14.7 J. Coming down: θ = 0°: W_down = +14.7 J. Whole trip: W = −14.7 + 14.7 = 0. Gravity takes energy from the ball on the way up and gives exactly the same back on the way down.

Worked example 4: a variable force

A force F = 3x² newton (x in metres, constant 3 N m⁻²) acts along the x-axis on a particle. Find the work done as the particle moves from x = 1 m to x = 3 m. Step 1: W = ∫ from 1 to 3 of 3x² dx = [x³] from 1 to 3. Step 2: W = 3³ − 1³ = 27 − 1 = 26 J.

Worked example 5: net work on a lifted load

A crane lifts a 200 kg crate through 6.0 m with a steady upward pull of 2400 N (take g = 10 m s⁻²). Work by the crane: θ = 0°, W₁ = 2400 × 6.0 = 14 400 J. Work by gravity: weight = 200 × 10 = 2000 N downward, θ = 180°, W₂ = −2000 × 6.0 = −12 000 J. Net work: 14 400 − 12 000 = +2400 J. A positive net work means the crate speeds up; the next lesson shows that this net work equals the gain in kinetic energy.

Key takeaways

  • Work needs both a force and a displacement; W = F dr cos θ is a scalar measured in joules.
  • θ < 90° gives positive work, θ = 90° gives zero work and θ > 90° gives negative work.
  • Constant force: W = (F cos θ)(r_f − r_i), the area of a rectangle on the F cos θ–r graph.
  • Variable force: W = ∫ F cos θ dr, the area under the curve.

Check your understanding

  1. 1. A force of 50 N acts on a box at 60° to its displacement of 4 m. The work done by the force is:

    1. 200 J
    2. 100 J
    3. 173 J
    4. zero
    Show answer

    Answer: B. W = F dr cos θ = 50 × 4 × cos 60° = 50 × 4 × 0.5 = 100 J. 200 J would be the answer only if the force were along the displacement.

  2. 2. A stone tied to a string is whirled in a horizontal circle at constant speed. The work done by the tension (the centripetal force) in one full revolution is:

    1. 2πr × T
    2. T × r
    3. positive but less than 2πr × T
    4. zero
    Show answer

    Answer: D. The tension acts along the radius, towards the centre, while each small displacement is along the tangent. θ = 90° at every instant, so cos θ = 0 and the work done is zero.

  3. 3. A 10 N force acts on a body at 120° to its 2 m displacement. The work done by the force is:

    1. −10 J
    2. +10 J
    3. −17.3 J
    4. +20 J
    Show answer

    Answer: A. W = F dr cos θ = 10 × 2 × cos 120° = 20 × (−0.5) = −10 J. The force has a component opposite to the motion, so the work is negative.

  4. 4. A force F = 2x newton (x in metres) moves a particle from x = 0 to x = 3 m along the x-axis. The work done is:

    1. 6 J
    2. 9 J
    3. 18 J
    4. 3 J
    Show answer

    Answer: B. W = ∫ from 0 to 3 of 2x dx = [x²] from 0 to 3 = 9 − 0 = 9 J. Multiplying the final force (6 N) by 3 m would wrongly give 18 J, because the force is not constant.

  5. 5. The dimensional formula of work is:

    1. [MLT⁻²]
    2. [ML²T⁻³]
    3. [ML²T⁻²]
    4. [ML⁻¹T⁻²]
    Show answer

    Answer: C. Work = force × displacement = [MLT⁻²] × [L] = [ML²T⁻²]. [MLT⁻²] is force and [ML²T⁻³] is power.

Privacy · Terms · Refunds · Delivery