The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".
Lesson 1
Conductivity of electrolytic solutions: resistivity, conductivity and molar conductivity
Λm = κ × 10⁻³ / M (κ in S m⁻¹, M in mol L⁻¹, Λm in S m² mol⁻¹). Equivalent conductance Λ = κ × 10⁻³ / N (S m² (gram equivalent)⁻¹).
From a bridge reading to molar conductance
1Balance the bridgeR = (P/Q) × S
2Cell constantl/A = κ(KCl) × R(KCl)
3Conductivityκ = (l/A) ÷ R
4Molar conductanceΛm = κ × 10⁻³ / M
Key takeaways: R = ρ(l/A); κ = (1/R)(l/A) in S m⁻¹; Λm = κ × 10⁻³/M in S m² mol⁻¹. Conductance rises with temperature, falls with viscosity and interionic attraction. Conductivity is measured with AC in a Wheatstone bridge, using a KCl solution to find the cell constant.
Variation of molar conductivity with concentration and Kohlrausch's law
Λm against √C for strong and weak electrolytes
Strong electrolyte (KCl)
Fully dissociated at all concentrations
Λm high, rises slowly and steadily on dilution
Λm against √C is a straight line
Λ°m found by extending the line to C = 0
Weak electrolyte (CH₃COOH)
Only partly dissociated
Λm low and almost flat at higher C
Rises very steeply as C approaches zero
Curve cannot be extended; use Kohlrausch's law
Λ°m(AₓBᵧ) = x λ°(Aʸ⁺) + y λ°(Bˣ⁻). For a weak electrolyte: α = Λm/Λ°m and Ka = CΛm² / [Λ°m(Λ°m − Λm)].
Key takeaways: Λm rises on dilution; for strong electrolytes Λm = Λ°m − k√C, a straight line. Weak electrolytes need Kohlrausch's law: Λ°m is the sum of the ions' λ° values. Then α = Λm/Λ°m, Ka = CΛm²/[Λ°m(Λ°m − Λm)], and the solubility of a sparingly soluble salt is κ × 10⁻³/Λ°m.
Galvanic cells, cell notation and standard electrode potentials
The complete circuit in a Daniel cell
1Zinc anodeZn → Zn²⁺ + 2e⁻
2External wireelectrons flow from zinc to copper
3Copper cathodeCu²⁺ + 2e⁻ → Cu
4Salt bridgeK⁺ to cathode side, Cl⁻ to anode side
↻ Then back to step 1: Zinc anode
E°cell = E°ox(anode) + E°red(cathode) = E°red(cathode) − E°red(anode). A positive E°cell means the cell reaction is spontaneous as written.
Part of the electrochemical series (standard reduction potentials at 298 K, as given in the Tamil Nadu textbook)
Half reaction
E° (V)
F₂ + 2e⁻ → 2F⁻
+2.87
Cl₂ + 2e⁻ → 2Cl⁻
+1.36
O₂ + 4H⁺ + 4e⁻ → 2H₂O
+1.23
Ag⁺ + e⁻ → Ag
+0.80
Fe³⁺ + e⁻ → Fe²⁺
+0.77
Cu²⁺ + 2e⁻ → Cu
+0.34
2H⁺ + 2e⁻ → H₂
0.00
Pb²⁺ + 2e⁻ → Pb
−0.13
Fe²⁺ + 2e⁻ → Fe
−0.44
Zn²⁺ + 2e⁻ → Zn
−0.76
Al³⁺ + 3e⁻ → Al
−1.66
Mg²⁺ + 2e⁻ → Mg
−2.36
Li⁺ + e⁻ → Li
−3.05
Key takeaways: in a galvanic cell oxidation happens at the negative anode and reduction at the positive cathode; the salt bridge keeps the solutions neutral. Notation puts the anode on the left: Zn | Zn²⁺ || Cu²⁺ | Cu. Electrode potentials are measured against the SHE (0 V); E°cell = E°(cathode) − E°(anode), and a positive value means a spontaneous reaction.
1Write the cell reactionanode oxidation + cathode reduction
2Find nelectrons transferred in the balanced equation
3Find E°cellE°(cathode) − E°(anode)
4Write Qproducts over reactants; leave out solids
5EcellE°cell − (0.0591/n) log Q
Key takeaways: 1 F ≈ 96 500 C mol⁻¹. ΔG = −nFE: a positive emf means a spontaneous reaction. E°cell = (0.0591/n) log K at 298 K. The Nernst equation, E = E° − (0.0591/n) log Q, gives the emf at any concentration; at equilibrium E = 0 and Q = K.
Electrolysis, Faraday's laws, batteries, fuel cells and corrosion
m = ZIt, with Z = M/(nF). Moles of product = It/(nF). Same charge in series: m₁/m₂ = E₁/E₂ (equivalent masses).
Batteries described in the Tamil Nadu textbook
Battery
Anode
Cathode
Electrolyte
emf (about)
Type
Leclanche (dry) cell
Zinc container
Graphite rod in contact with MnO₂
NH₄Cl and ZnCl₂ in water
1.5 V
Primary
Mercury button cell
Zinc amalgamated with mercury
HgO mixed with graphite
Paste of KOH and ZnO
1.35 V
Primary
Lead storage battery
Spongy lead
Lead plate bearing PbO₂
38% H₂SO₄ by mass (density 1.2 g mL⁻¹)
2 V per cell
Secondary
Lithium-ion battery
Porous graphite
Transition metal oxide such as CoO₂
Lithium salt in an organic solvent
not given
Secondary
Ways to protect a metal from corrosion
Barrier coating
Paint the surface
Galvanising: coat iron with zinc, which is oxidised instead of iron
Cathodic protection
Join Mg or Zn as a sacrificial anode
Iron becomes the cathode and is protected
Passivation
Treat with a strong oxidising agent such as concentrated HNO₃
A protective oxide layer forms
Alloying
Alloy iron with a more anodic metal
Stainless steel: iron with chromium
Key takeaways: electrolysis drives a non-spontaneous reaction; molten NaCl needs more than 4.07 V. m = ZIt and Z = M/(nF); in series, masses go as equivalent masses. Primary cells (Leclanche, mercury) cannot be recharged; secondary cells (lead storage, Li-ion) can. Fuel cells turn combustion energy straight into electricity. Rusting is an electrochemical cell on the iron surface, prevented by coatings, sacrificial anodes, passivation or alloying.