Revision notes

Unit 10 Electronics and Communication: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Energy bands and semiconductors: intrinsic, n-type and p-type

TypeBand pictureBand gapResistivity (as given in the textbook)
InsulatorFull VB, empty CB, wide gapAbout 6 eV10¹¹ to 10¹⁹ Ω m
ConductorVB and CB overlapNo gapVery low (good metals about 10⁻⁸ Ω m)
SemiconductorNarrow gapLess than 3 eV10⁻⁵ to 10⁶ Ω m

Band pictures of the three kinds of solid

  • Insulator
    • Wide gap, about 6 eV
    • No free electrons
    • Does not conduct
  • Semiconductor
    • Narrow gap, under 3 eV
    • A few electrons cross at room temperature
    • Conducts more when hotter
  • Conductor
    • Bands overlap
    • Many free electrons
    • Conducts well even when cold

Kinds of semiconductor

  • Intrinsic (pure Si or Ge)
    • Electrons = holes
    • Carriers made by heat only
  • n-type (add P, As or Sb)
    • Donor level just below CB
    • Majority: electrons
    • Minority: holes
  • p-type (add B, Al, Ga or In)
    • Acceptor level just above VB
    • Majority: holes
    • Minority: electrons

Pentavalent dopant → donor → n-type, electrons majority. Trivalent dopant → acceptor → p-type, holes majority. E_g(Si) = 1.1 eV, E_g(Ge) = 0.7 eV.

  • Closely packed atoms turn sharp levels into valence and conduction bands separated by E_g.
  • Insulator: wide gap (about 6 eV); conductor: overlapping bands; semiconductor: narrow gap (under 3 eV) and negative temperature coefficient.
  • Intrinsic: n_e = n_h; a hole behaves as a positive carrier.
  • Group V dopants give n-type (electrons majority); group III dopants give p-type (holes majority).
Read the full lesson

Lesson 2

The p-n junction diode: biasing, characteristics, rectifiers, breakdown and the Zener regulator

How the junction reaches equilibrium

  1. Majority carriers diffuse across Electrons n → p, holes p → n
  2. Fixed ions are left behind Positive ions on n-side, negative on p-side
  3. Field and barrier grow Drift of minority carriers increases
  4. Drift balances diffusion No net current; depletion width set

Then back to step 1: Majority carriers diffuse across

Half-wave and full-wave rectifiers

  • Half-wave
    • One diode
    • Passes one half cycle only
    • Maximum efficiency 40.6%
  • Full-wave (centre tap)
    • Two diodes and a centre-tapped transformer
    • Both half cycles, same direction through the load
    • Maximum efficiency 81.2%

I_s = (V_in − V_Z)/R_s; I_L = V_Z/R_L; I_Z = I_s − I_L.

  • Diffusion of majority carriers leaves fixed ions: depletion layer and barrier potential (0.7 V Si, 0.3 V Ge).
  • Forward bias narrows the depletion layer and the diode conducts beyond the knee voltage; reverse bias widens it and only a tiny saturation current flows.
  • Half-wave rectifier: one half cycle, 40.6%; full-wave centre-tap: both half cycles, 81.2%.
  • Avalanche breakdown: lightly doped, collisions; Zener breakdown: heavily doped, strong field.
  • A reverse-biased Zener holds V_Z across a parallel load: I_Z = I_s − I_L.
Read the full lesson

Lesson 3

Optoelectronic devices and the bipolar junction transistor

Three optoelectronic junction devices

  • LED
    • Forward biased
    • Electricity → light
    • Colour set by band gap
  • Photodiode
    • Reverse biased
    • Light → current (signal)
    • Current grows with intensity
  • Solar cell
    • No bias needed
    • Light → emf (power)
    • Joined into panels and arrays
Biasing modeEmitter-base junctionCollector-base junctionUse
ActiveForwardReverseAmplifier
SaturationForwardForwardClosed switch (ON)
Cut-offReverseReverseOpen switch (OFF)

I_E = I_B + I_C; α = I_C/I_E; β = I_C/I_B; β = α/(1 − α); α = β/(1 + β).

  • LED: forward biased, λ ≈ 1240/E_g nm; photodiode: reverse biased, current ∝ light; solar cell: no bias, generates emf.
  • BJT: heavily doped emitter, thin lightly doped base, large collector; arrow points p → n.
  • Active = amplifier; saturation = ON switch; cut-off = OFF switch.
  • I_E = I_B + I_C; α = I_C/I_E (0.95-0.99); β = I_C/I_B; β = α/(1 − α).
  • CE: input impedance high, output impedance low, β large.
Read the full lesson

Lesson 4

Transistor circuits and digital electronics: load line, switch, amplifier, oscillator, logic gates and Boolean algebra

How an oscillator keeps going

  1. Tank circuit oscillates Energy swaps between L and C at f = 1/2π√(LC)
  2. Amplifier boosts the signal Transistor in active mode
  3. Positive feedback returns part of the output In phase, loop gain Aβ = 1
  4. Energy losses are replaced Oscillations stay undamped

Then back to step 1: Tank circuit oscillates

Truth table for the two-input gates (NOT simply turns 0 into 1 and 1 into 0)
ABAND A·BOR A + BNANDNOREx-OR
0000110
0101101
1001101
1111000

De Morgan: NOT(A + B) = A̅·B̅ (NOR = bubbled AND); NOT(A·B) = A̅ + B̅ (NAND = bubbled OR).

  • Load line V_CE = V_CC − I_C R_C; Q point mid-line for amplifiers, cut-off/saturation for switches.
  • Switch: low in, high out, so the transistor is a NOT gate; CE amplifier output is 180° out of phase.
  • Oscillator = tank + amplifier + positive feedback, with Aβ = 1 and f = 1/2π√(LC).
  • AND, OR, NOT are basic; NAND and NOR are universal; Ex-OR gives 1 when inputs differ.
  • De Morgan: NOT(A + B) = A̅·B̅ and NOT(A·B) = A̅ + B̅.
Read the full lesson

Lesson 5

Communication systems: modulation, the communication chain, wave propagation and modern systems

AM and FM compared (points as listed in the Tamil Nadu textbook)
FeatureAmplitude modulationFrequency modulation
What changesCarrier amplitudeCarrier frequency
AdvantagesEasy to transmit and receive; narrower bandwidth; low-cost equipmentMuch less noise (better signal-to-noise ratio); large operating range; high transmission efficiency; bandwidth covers the whole audible range, so better sound
LimitationsMore noise; lower efficiency; smaller operating rangeNeeds a much wider channel; costlier, more complex sets; covers a smaller area

From the speaker to the listener

  1. Information Speech, music, pictures or data
  2. Input transducer Microphone turns sound into an electrical signal
  3. Transmitter Amplifier, oscillator (carrier), modulator, power amplifier
  4. Transmitting antenna Radiates EM waves at the speed of light
  5. Channel Wires, cables, optical fibre or free space
  6. Receiver Antenna, demodulator, amplifier
  7. Output transducer Loudspeaker, screen or computer
ModeApproximate frequencies (textbook)How it travelsUsed for
Ground (surface) wave2 kHz to 2 MHzGlides along the Earth's surface; attenuates with distanceLocal broadcasting, radio navigation, ship communication
Sky (ionospheric) wave3 MHz to 30 MHzBent back to Earth by the ionosphereLong-distance radio
Space waveAbove 30 MHz (up to about 400 GHz)Straight line, line of sightTV, satellite communication, radar

Line of sight: d = √(2Rh) for one antenna; d = √(2Rh_T) + √(2Rh_R) between two; bandwidth = ν₂ − ν₁.

  • Modulation puts a low-frequency baseband signal on a high-frequency carrier for long-distance transmission.
  • AM varies amplitude (simple, narrow band, noisy); FM varies frequency (less noise, better sound, wider channel); PM varies phase.
  • Chain: transducer → transmitter (amplifier, oscillator, modulator, power amplifier) → antenna → channel → receiver (demodulator, amplifier) → output transducer.
  • Ground waves 2 kHz-2 MHz; sky waves 3-30 MHz via the ionosphere (skip distance, skip zone); space waves above 30 MHz, line of sight, d = √(2Rh).
  • Satellites (6 GHz up, 4 GHz down), optical fibres (total internal reflection), radar (d = ct/2), mobile and internet.
Read the full lesson

Privacy · Terms · Refunds · Delivery