- Practice
- About 25 min
- 5 practice questions
The p-n junction diode: biasing, characteristics, rectifiers, breakdown and the Zener regulator
Explain how a depletion layer and barrier potential form, describe forward and reverse bias and the diode's V-I curve, analyse half-wave and full-wave rectifiers, and use a Zener diode as a voltage regulator.
If something looks wrong, please tell us.
By the end of this lesson you can
- Explain diffusion and drift currents, the depletion region and the barrier potential.
- Describe forward and reverse bias and read the V-I characteristics of a diode.
- Solve simple diode circuits.
- Explain half-wave and full-wave (centre-tap) rectifiers and their efficiencies.
- Distinguish avalanche and Zener breakdown and analyse a Zener voltage regulator.
Joining p-type and n-type regions in one crystal produces a p-n junction, the simplest semiconductor device and the heart of the diode, the LED, the solar cell and the transistor. Its key property is that it lets current through easily in one direction only.
Formation of the depletion layer
A single crystal is doped so that one side is p-type and the other n-type. The n-side has many electrons and the p-side many holes, so electrons diffuse into the p-side and holes into the n-side; this flow of majority carriers is the diffusion current. Each electron that leaves the n-side leaves behind a fixed positive donor ion; each electron arriving on the p-side fills a hole and makes a fixed negative acceptor ion. The thin region near the junction, emptied of free carriers and holding only these immobile ions, is the depletion region.
The ions create an electric field across the junction, from the positive n-side layer to the negative p-side layer. This field sweeps minority carriers across (electrons from p to n, holes from n to p): the drift current, opposite to the diffusion current. As diffusion builds up more ions, the field and the drift current grow until the two currents are equal and there is no net current. The potential difference across the depletion layer at equilibrium is the barrier potential V_b: about 0.7 V for silicon and 0.3 V for germanium at 25 °C.
How the junction reaches equilibrium
- Majority carriers diffuse across Electrons n → p, holes p → n
- Fixed ions are left behind Positive ions on n-side, negative on p-side
- Field and barrier grow Drift of minority carriers increases
- Drift balances diffusion No net current; depletion width set
Then back to step 1: Majority carriers diffuse across
Forward and reverse bias
Biasing means applying an external voltage. In forward bias the positive terminal goes to the p-side and the negative to the n-side. Electrons and holes are pushed towards the junction, the depletion layer narrows and the barrier falls, so a large current flows once the applied voltage exceeds the barrier. In reverse bias the positive terminal goes to the n-side. Carriers are pulled away from the junction, the depletion layer widens and the barrier rises, so the majority carriers cannot cross. Only a tiny current of minority carriers flows, the reverse saturation current I_s. It hardly depends on the voltage, depends on the number of thermally generated minority carriers, and for silicon roughly doubles for every 10 °C rise.
V-I characteristics
- Forward: almost no current until the knee (cut-in, threshold) voltage, about 0.7 V for Si and 0.3 V for Ge; then the current rises steeply (exponentially). The curve is not a straight line, so a diode does not obey Ohm's law.
- Forward resistance r_F = ΔV_F/ΔI_F is small: a forward-biased diode acts like a conductor (a closed switch).
- Reverse: a tiny leakage current (μA) that stays almost constant: a reverse-biased diode acts like an insulator (an open switch).
- Beyond the breakdown voltage in reverse the current rises sharply; an ordinary diode is destroyed by overheating, so it is operated between the knee voltage and breakdown.
- An ideal diode has zero forward resistance and zero barrier potential, and infinite reverse resistance.
Rectifiers
Rectification converts alternating current into direct current. A half-wave rectifier uses a transformer, one diode and a load resistor R_L. In the half cycle when the diode is forward biased, current flows through R_L; in the other half cycle the diode is reverse biased and blocks it. The output is a pulsating DC with only one half of each cycle, and the efficiency (DC output power/AC input power) is at most 40.6%.
A full-wave (centre-tap) rectifier uses a centre-tapped transformer and two diodes D₁ and D₂, with the centre tap as the zero reference. In one half cycle one end of the secondary is positive, D₁ conducts and D₂ is reverse biased; in the next half cycle D₂ conducts and D₁ is off. Current flows through R_L in the same direction in both half cycles. The efficiency is twice as large, 81.2%. The output is still pulsating, so filter circuits are used to smooth it into a steady DC.
Half-wave and full-wave rectifiers
-
Half-wave
- One diode
- Passes one half cycle only
- Maximum efficiency 40.6%
-
Full-wave (centre tap)
- Two diodes and a centre-tapped transformer
- Both half cycles, same direction through the load
- Maximum efficiency 81.2%
Breakdown: avalanche and Zener
Avalanche breakdown occurs in lightly doped junctions with wide depletion layers. At high reverse voltage, minority carriers gain enough kinetic energy to break covalent bonds when they collide with atoms, creating electron-hole pairs that are themselves accelerated: an avalanche of carriers. Zener breakdown occurs in heavily doped junctions with very narrow depletion layers (under about 10⁻⁶ m). Even a modest reverse voltage then gives a huge field, about 3 × 10⁷ V m⁻¹, which tears electrons directly out of covalent bonds (the Zener effect). Zener breakdown therefore happens at lower reverse voltages than avalanche breakdown.
The Zener diode and voltage regulation
A Zener diode (named after Clarence Zener) is a heavily doped silicon diode designed to work in reverse breakdown; breakdown voltages from about 2 V to over 1000 V can be made by choosing the doping. Forward biased it behaves like an ordinary diode (conducting from about 0.7 V). In reverse, once the voltage reaches V_Z the current rises sharply while the voltage stays almost constant. It must carry at least a minimum current I_Z(min) to stay in breakdown and less than I_Z(max), set by its maximum power dissipation. The small slope of the breakdown line is the Zener dynamic impedance. Uses: voltage regulators, fixed reference voltages and protecting equipment from accidental high voltages.
Voltage regulator: the Zener diode is reverse biased in series with a resistor R_s, and the load R_L is connected in parallel with the diode. As long as the input is above V_Z, the voltage across the diode, and hence across the load, stays at V_Z. If the input rises, the Zener current and the drop across R_s rise; if it falls, they fall. The changes appear across R_s (the dropping resistor) while the output stays constant.
I_s = (V_in − V_Z)/R_s; I_L = V_Z/R_L; I_Z = I_s − I_L.
Worked example 1: a diode in a circuit
A silicon diode (0.7 V drop) is forward biased in series with a 2.0 kΩ resistor across a 5.0 V battery. Step 1: voltage across the resistor = 5.0 − 0.7 = 4.3 V. Step 2: I = 4.3/2000 = 2.15 × 10⁻³ A = 2.15 mA. If the diode were ideal, I = 5.0/2000 = 2.5 mA. If the battery were reversed, the diode would be reverse biased and the current would be practically zero.
Worked example 2: Zener regulator currents
A 6.0 V Zener diode is fed from 12 V through R_s = 200 Ω, with a load R_L = 1.0 kΩ across it. Step 1: drop across R_s = 12 − 6.0 = 6.0 V, so I_s = 6.0/200 = 30 mA. Step 2: load voltage = V_Z = 6.0 V, so I_L = 6.0/1000 = 6.0 mA. Step 3: I_Z = I_s − I_L = 30 − 6.0 = 24 mA. If the input rises to 14 V, I_s = 8.0/200 = 40 mA and I_Z = 34 mA, while the load still gets 6.0 V and 6.0 mA.
Key takeaways
- Diffusion of majority carriers leaves fixed ions: depletion layer and barrier potential (0.7 V Si, 0.3 V Ge).
- Forward bias narrows the depletion layer and the diode conducts beyond the knee voltage; reverse bias widens it and only a tiny saturation current flows.
- Half-wave rectifier: one half cycle, 40.6%; full-wave centre-tap: both half cycles, 81.2%.
- Avalanche breakdown: lightly doped, collisions; Zener breakdown: heavily doped, strong field.
- A reverse-biased Zener holds V_Z across a parallel load: I_Z = I_s − I_L.
Check your understanding
-
1. When a p-n junction is forward biased, the depletion region:
- Becomes wider
- Becomes narrower
- Is unchanged
- Disappears at any voltage
Show answer
Answer: B. Forward bias pushes majority carriers towards the junction, where they neutralise some of the fixed ions, so the depletion region narrows and the barrier falls.
-
2. A germanium diode (0.3 V drop) is forward biased in series with a 1.0 kΩ resistor across a 3.3 V supply. The current is:
- 3.3 mA
- 3.6 mA
- 0.3 mA
- 3.0 mA
Show answer
Answer: D. Voltage across the resistor = 3.3 − 0.3 = 3.0 V, so I = 3.0 V/1000 Ω = 3.0 × 10⁻³ A = 3.0 mA.
-
3. The maximum efficiency of a full-wave rectifier is:
- 40.6%
- 100%
- 81.2%
- 50%
Show answer
Answer: C. A full-wave rectifier uses both half cycles, so its maximum efficiency is twice that of a half-wave rectifier: 2 × 40.6% = 81.2%.
-
4. Zener breakdown differs from avalanche breakdown because it:
- Occurs in heavily doped junctions where a strong field breaks bonds directly
- Occurs only in forward bias
- Needs carriers to collide many times
- Happens only in germanium
Show answer
Answer: A. In heavily doped junctions the depletion layer is very thin, so a modest reverse voltage gives a field of about 3 × 10⁷ V m⁻¹ that ruptures bonds directly. Avalanche breakdown is in lightly doped junctions and relies on collisions.
-
5. A 9 V Zener is supplied from 15 V through a 1.0 kΩ resistor and feeds a 2.0 kΩ load. The current through the Zener is:
- 6.0 mA
- 4.5 mA
- 10.5 mA
- 1.5 mA
Show answer
Answer: D. I_s = (15 − 9)/1000 = 6.0 mA. I_L = 9/2000 = 4.5 mA. I_Z = 6.0 − 4.5 = 1.5 mA.
Sign in to keep track of the lessons you finish.