• Practice
  • About 25 min
  • 5 practice questions

Optoelectronic devices and the bipolar junction transistor

Explain how an LED, a photodiode and a solar cell work, describe NPN and PNP transistors, their biasing modes and configurations, and use α, β and the CE characteristics of a transistor.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain the LED, find the colour from the band gap, and describe the photodiode and solar cell.
  • Describe the structure, symbols and doping of NPN and PNP transistors.
  • State the active, saturation and cut-off biasing modes and the CB, CE and CC configurations.
  • Explain transistor action and use I_E = I_B + I_C, α = I_C/I_E and β = I_C/I_B.
  • Read the input, output and transfer characteristics in CE mode and relate α and β.

Junctions can turn electricity into light and light into electricity, and two junctions back to back make a transistor, a device that lets a small current control a large one. This lesson covers both.

Light emitting diode (LED)

An LED is a p-n junction that emits light when forward biased (electroluminescence). Electrons from the n-side and holes from the p-side cross the junction and become excess minority carriers, which recombine with majority carriers. Each recombination releases energy either as light (radiative) or as heat (non-radiative). The photon energy is about the band gap, so the colour depends on the band gap: hν ≈ E_g, giving λ = hc/E_g, or λ (nm) ≈ 1240/E_g (eV). Examples given in the textbook: blue from SiC, green from AlGaP, red from GaAsP, and white from GaInN. Uses include indicator lamps, traffic signals, emergency vehicle lights, TV and air-conditioner remote controls and general lighting.

Photodiode

A photodiode converts light into an electric signal; it works the opposite way to an LED and is operated in reverse bias. Light falls on the junction through a small window. A photon with enough energy creates an electron-hole pair in the depletion region, and the field sweeps electrons to the n-side and holes to the p-side before they recombine, giving a photocurrent that grows with the light intensity. With no light, a tiny dark current of thermally generated carriers flows. Uses: counting items on conveyor belts, compact disc players, smoke detectors and medical detectors.

Solar cell

A solar (photovoltaic) cell generates an emf when light falls on its junction, needing no external bias (photovoltaic effect). Light creates electron-hole pairs near the junction; the built-in field of the depletion region sends electrons to the n-layer, collected by metal finger contacts on the front, and holes to the p-layer, collected by the back contact. Connecting a load lets a photocurrent flow. Cells are joined in series and parallel into panels and panels into arrays for calculators, watches, satellites and solar power plants.

Three optoelectronic junction devices

  • LED
    • Forward biased
    • Electricity → light
    • Colour set by band gap
  • Photodiode
    • Reverse biased
    • Light → current (signal)
    • Current grows with intensity
  • Solar cell
    • No bias needed
    • Light → emf (power)
    • Joined into panels and arrays

The bipolar junction transistor

A BJT is a crystal with three regions: either an n-type layer between two p-type layers (PNP) or a p-type layer between two n-type layers (NPN). The regions are the emitter (E), base (B) and collector (C), with two junctions: emitter-base (J_EB) and collector-base (J_CB). The emitter is heavily doped, because it supplies the majority carriers. The base is very thin (about 10⁻⁶ m) and lightly doped. The collector is moderately doped and physically the largest, because it collects the carriers and dissipates the most power. In the symbol, the arrow on the emitter points from p to n, the direction of conventional current: outwards for NPN, inwards for PNP.

Biasing modeEmitter-base junctionCollector-base junctionUse
ActiveForwardReverseAmplifier
SaturationForwardForwardClosed switch (ON)
Cut-offReverseReverseOpen switch (OFF)

A transistor has three terminals, so one is common to input and output: common base (CB), input current I_E, output current I_C; common emitter (CE), input I_B, output I_C; common collector (CC), input I_B, output I_E.

Transistor action (NPN, active mode)

The forward-biased emitter-base junction sends many electrons from the heavily doped emitter into the base: the emitter current I_E. The base is thin and lightly doped, so only a few of these electrons find holes to recombine with; the holes lost are replaced from the base supply, forming the small base current I_B (microamperes). Most electrons cross into the collector, where the reverse-biased collector junction and the positive collector pull them out: the collector current I_C (milliamperes). By Kirchhoff's current law I_E = I_B + I_C, and since I_B is small, I_C ≈ I_E. If I_E is zero, I_C is almost zero, so the BJT is a current-controlled device. A small extra collector current from thermally generated carriers, I_CO, rises with temperature. A PNP transistor works the same way with holes as the emitter's majority carriers.

The current gain in CB mode is α = I_C/I_E. It is a measure of transistor quality: always slightly less than 1, typically 0.95 to 0.99, meaning 95% to 99% of the emitter current reaches the collector.

Characteristics in common emitter mode

  • Input characteristic (I_B against V_BE at constant V_CE): like a diode's forward curve, with a knee at about 0.7 V (Si) or 0.3 V (Ge). Raising V_CE widens the collector depletion layer, narrows the effective base and lowers I_B (the curve shifts outward). Input impedance r_i = ΔV_BE/ΔI_B at constant V_CE is high in CE mode.
  • Output characteristic (I_C against V_CE at constant I_B): I_C rises quickly up to the knee voltage (the saturation region), then stays nearly flat (the active region, used for amplification); the region below the I_B = 0 curve is cut-off; far beyond the rated V_CE, breakdown can damage the transistor. Output impedance r_o = ΔV_CE/ΔI_C at constant I_B is low in CE mode (as the textbook states).
  • Current transfer characteristic (I_C against I_B at constant V_CE): nearly a straight line; a small current I_CEO (leakage) flows even when I_B = 0. Its slope is the forward current gain β = ΔI_C/ΔI_B, typically large (tens to hundreds).

Relation between α and β. Divide I_E = I_B + I_C by I_C: 1/α = 1/β + 1, which gives β = α/(1 − α) and α = β/(1 + β). Since α is close to 1, β is large.

I_E = I_B + I_C; α = I_C/I_E; β = I_C/I_B; β = α/(1 − α); α = β/(1 + β).

Worked example 1: LED colour

An LED material has E_g = 2.25 eV. Step 1: λ = hc/E_g = (6.63 × 10⁻³⁴ × 3.0 × 10⁸)/(2.25 × 1.6 × 10⁻¹⁹) = (1.989 × 10⁻²⁵)/(3.6 × 10⁻¹⁹) = 5.53 × 10⁻⁷ m ≈ 550 nm. Step 2: the shortcut 1240/2.25 = 551 nm agrees. 550 nm is green light. A silicon junction (E_g = 1.1 eV) would give 1240/1.1 ≈ 1130 nm, in the infrared, which is why silicon is not used for visible LEDs.

Worked example 2: transistor currents and gains

A transistor has α = 0.98 and an emitter current of 5.0 mA. Step 1: I_C = αI_E = 0.98 × 5.0 = 4.9 mA. Step 2: I_B = I_E − I_C = 5.0 − 4.9 = 0.10 mA. Step 3: β = I_C/I_B = 4.9/0.10 = 49. Check: β = α/(1 − α) = 0.98/0.02 = 49. Conversely, a transistor with β = 99 has α = 99/100 = 0.99.

Key takeaways

  • LED: forward biased, λ ≈ 1240/E_g nm; photodiode: reverse biased, current ∝ light; solar cell: no bias, generates emf.
  • BJT: heavily doped emitter, thin lightly doped base, large collector; arrow points p → n.
  • Active = amplifier; saturation = ON switch; cut-off = OFF switch.
  • I_E = I_B + I_C; α = I_C/I_E (0.95-0.99); β = I_C/I_B; β = α/(1 − α).
  • CE: input impedance high, output impedance low, β large.

Check your understanding

  1. 1. An LED emits light of wavelength 620 nm. Its band gap is about:

    1. 2.0 eV
    2. 1.1 eV
    3. 3.0 eV
    4. 0.62 eV
    Show answer

    Answer: A. E_g ≈ 1240/λ(nm) = 1240/620 = 2.0 eV.

  2. 2. A photodiode is normally operated:

    1. In forward bias
    2. With no bias at all
    3. In reverse bias
    4. Only in breakdown
    Show answer

    Answer: C. A photodiode is reverse biased: light creates electron-hole pairs in the depletion region and the field sweeps them across to give a photocurrent proportional to intensity. The solar cell is the device that needs no bias.

  3. 3. In a transistor the base is made thin and lightly doped so that:

    1. The base current is large
    2. Most carriers from the emitter reach the collector
    3. The emitter current becomes zero
    4. The collector can be made small
    Show answer

    Answer: B. A thin, lightly doped base has few holes, so few injected electrons recombine there; most cross into the collector. This makes I_C close to I_E and the base current small.

  4. 4. For a transistor with β = 50, α is about:

    1. 0.50
    2. 1.02
    3. 0.020
    4. 0.98
    Show answer

    Answer: D. α = β/(1 + β) = 50/51 = 0.98.

  5. 5. In common base mode α = 0.95 and I_E = 2.0 mA. The base current is:

    1. 1.9 mA
    2. 0.10 mA
    3. 0.050 mA
    4. 2.1 mA
    Show answer

    Answer: B. I_C = αI_E = 0.95 × 2.0 = 1.9 mA, so I_B = I_E − I_C = 2.0 − 1.9 = 0.10 mA.

Privacy · Terms · Refunds · Delivery