Revision notes

Unit 4 Electric charge and Electric current: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Electric charge, ions and the electric force

Attraction and repulsion

  • Like charges
    • + and +
    • − and −
    • Repel each other
    • Two rubbed balloons push apart
  • Unlike charges
    • + and −
    • Attract each other
    • Charged comb pulls paper bits
    • Rubbed balloon sticks to a wall

q = ne, with e = 1.6 × 10⁻¹⁹ C. Like charges repel, unlike charges attract. Rubbing transfers electrons; it does not create charge.

Key takeaways: matter is normally neutral; losing electrons makes a body positive and gaining them makes it negative. Charge comes in whole-number multiples of e, is measured in coulombs and adds up algebraically. The force between charges is attractive or repulsive and grows with the charges and weakens with distance.

Read the full lesson

Lesson 2

Electric field, electric potential and electric current

Conventional current and electron flow

  • Conventional current
    • Imagined flow of positive charge
    • From + terminal to − terminal outside the cell
    • From higher to lower potential
    • Used in circuit diagrams
  • Electron current
    • Real flow of electrons in a wire
    • From − terminal to + terminal outside the cell
    • From lower to higher potential
    • Opposite to conventional current

I = q/t; 1 A = 1 C/s. Conventional current flows from + to − outside the cell; electrons flow from − to +. Ammeter: in series.

Key takeaways: an electric field is the region where a charge feels a force, shown by lines of force from + to −. Potential is work per unit positive charge, in volts. Current is the rate of flow of charge in amperes; conventional current is opposite to electron flow, and an ammeter goes in series.

Read the full lesson

Lesson 3

E.m.f., potential difference, resistance and Ohm's law

Ammeter and voltmeter

  • Ammeter
    • Measures current (A)
    • Connected in series
    • Current passes through it
  • Voltmeter
    • Measures potential difference (V)
    • Connected in parallel, across the component
    • Red to + side, black to − side

ε = W/q and V = W/q (volt = joule per coulomb). Ohm's law: V = IR, so R = V/I (ohm).

Key takeaways: a cell's e.m.f. is the work it does per coulomb; the p.d. across a device is the energy it converts per coulomb. Resistance opposes current and is measured in ohms. For a conductor at constant temperature, V = IR.

Read the full lesson

Lesson 4

Circuit diagrams, series and parallel circuits

Some common circuit symbols, described in words
ComponentHow its symbol looks
CellA long line (+) and a short line (−) side by side
BatteryTwo or more cell symbols joined in a row
Switch (open)A short line hinged up, leaving a gap in the wire
Fixed resistorA small rectangle (or a zigzag line) in the wire
Variable resistor (rheostat)A resistor with an arrow across it
Light bulbA circle with a cross inside
AmmeterA circle with the letter A
VoltmeterA circle with the letter V
GalvanometerA circle with G or an arrow
FuseA small rectangle with a line running through it
Earth connectionThree horizontal lines getting shorter
Wires joinedCrossing lines with a dot where they meet

Series versus parallel

  • Series
    • One single loop
    • Same current everywhere
    • Voltage shared between parts
    • One break stops everything
    • Used in decorative light strings
  • Parallel
    • Two or more branches
    • Same p.d. across each branch
    • Main current = sum of branch currents
    • Each branch works on its own
    • Used for house wiring

Series: one path, same current, voltages add up to the supply. Parallel: many paths, same voltage, branch currents add up to the main current.

Key takeaways: a circuit needs a source, wires, a switch and a load in a closed loop. Standard symbols describe circuits. Series circuits keep the current the same; parallel circuits keep the voltage the same, which is why homes are wired in parallel.

Read the full lesson

Lesson 5

Effects of electric current, ac and dc, and electrical safety

Effects of electric current

  • Heating effect
    • Electric iron
    • Water heater
    • Toaster
  • Chemical effect
    • Electrolysis
    • Electroplating
    • Electro-refining of metals
  • Magnetic effect
    • Electromagnets
    • Electric bell
    • Motors

ac and dc

  • Alternating current (ac)
    • Direction reverses regularly
    • Voltage changed easily by transformers
    • Sent over long distances with little loss
    • Easier to generate; easily changed to dc
  • Direct current (dc)
    • Flows one way only
    • Needed for electroplating and electro-refining
    • Can be stored in cells and batteries
    • From cells, batteries, solar cells

Heating (Joule), chemical (electrolysis, electroplating) and magnetic effects. dc flows one way; ac reverses. Rectifier: ac to dc; inverter: dc to ac. Experiments only with small cells, never mains.

Key takeaways: current heats resistors, drives chemical changes in electrolytes and produces magnetic fields. ac is easy to transform and transmit; dc is needed for plating and storage. Respect electricity: dry hands, good insulation, no overloading and no experiments with the mains.

Read the full lesson

Privacy · Terms · Refunds · Delivery