- Practice
- About 16 min
- 5 practice questions
E.m.f., potential difference, resistance and Ohm's law
Explain e.m.f. and potential difference with the water-pump picture, use V = W/q, connect a voltmeter, describe resistance and resistors, and apply Ohm's law V = IR.
If something looks wrong, please tell us.
By the end of this lesson you can
- Explain e.m.f. using the comparison with a water pump.
- Use ε = W/q and V = W/q, and tell e.m.f. from potential difference.
- Connect a voltmeter correctly.
- Describe resistance, conductors, insulators and resistors.
- Use Ohm's law, V = IR, including from a graph.
A closed pipe full of water does not flow on its own. Put a pump in the pipe and the water starts moving and can turn a water wheel to do work. A copper wire is full of free electrons, but they drift about at random until something pushes them one way. In a circuit, the 'pump' is the cell.
Electromotive force (e.m.f.)
A cell or other source drives charges round a circuit by doing work on them. The electromotive force (e.m.f.), ε, of a source is the work done by the source in driving a unit charge round the complete circuit: ε = W/q. Its unit is the joule per coulomb, the volt (V). A source has an e.m.f. of 1 V if it does 1 J of work to drive 1 C of charge round the circuit.
Worked example 1: energy from a cell
Question: A 1.5 V cell drives 4 C of charge round a circuit. How much energy does it supply? Working: W = εq = 1.5 × 4 = 6 J.
Potential difference
In a bulb, fan or heater, electrical energy is changed into light, heat or motion. The energy changed per coulomb of charge passing through a component is the potential difference (p.d.) across it: V = W/q. Its unit is also the volt. The difference between the two: e.m.f. is the voltage across the terminals of a source when it is not sending current; potential difference is the voltage between any two points in a circuit, such as across a device, while current flows.
A voltmeter measures potential difference. It is connected in parallel (across) the component, with its positive (red) terminal to the positive side of the circuit and its negative (black) terminal to the negative side.
Worked example 2: p.d. across a heater
Question: 1.5 × 10⁴ C of charge flows through a heater, which turns 3.3 × 10⁶ J of electrical energy into heat. Find the p.d. across it. Working: V = W/q = 3.3 × 10⁶ ÷ 1.5 × 10⁴ = 220 V.
Resistance
Resistance (R) measures how much a component opposes the flow of current through it. Its SI unit is the ohm (Ω): a component has 1 Ω of resistance if a p.d. of 1 V across it drives a current of 1 A. Copper and aluminium have very low resistance and are good conductors, used for wires. Nichrome and tin oxide have high resistance and are used where heat is wanted. Insulators such as glass, rubber, plastic polymers and paper practically do not conduct, so they cover wires for safety. The resistance of a wire depends on its material, its shape and size (length and thickness) and its temperature.
Components made to provide resistance are resistors. A fixed resistor has one value; a variable resistor such as a rheostat can be adjusted to control the current in a circuit.
Ohm's law
Ohm's law: at a constant temperature, the current through a conductor is directly proportional to the potential difference across its ends. So V/I is constant, and that constant is the resistance: V = IR. A graph of V against I for such a conductor is a straight line through the origin, and its slope is R.
Worked example 3: using V = IR
Question: A 6 V battery is connected across a 12 Ω resistor. What current flows? What p.d. would drive 2 A through it? Working: I = V/R = 6 ÷ 12 = 0.5 A. V = IR = 2 × 12 = 24 V.
Worked example 4: resistance from readings
Question (made-up readings): For a resistor, I = 0.5, 1.0, 1.5, 2.0 A gave V = 2.5, 5.0, 7.5, 10.0 V. Find R. Working: V/I = 2.5/0.5 = 5.0/1.0 = 7.5/1.5 = 10.0/2.0 = 5 Ω each time; the V-I graph is a straight line of slope 5 Ω. With real readings the ratios scatter slightly, so draw the best straight line and take its slope.
Ammeter and voltmeter
-
Ammeter
- Measures current (A)
- Connected in series
- Current passes through it
-
Voltmeter
- Measures potential difference (V)
- Connected in parallel, across the component
- Red to + side, black to − side
ε = W/q and V = W/q (volt = joule per coulomb). Ohm's law: V = IR, so R = V/I (ohm).
Key takeaways: a cell's e.m.f. is the work it does per coulomb; the p.d. across a device is the energy it converts per coulomb. Resistance opposes current and is measured in ohms. For a conductor at constant temperature, V = IR.
Check your understanding
-
1. In the water-pipe comparison, the cell in an electric circuit is like
- the water
- the pipe
- the water wheel
- the pump
Show answer
Answer: D. The pump pushes water round the pipe; the cell pushes charges round the circuit. The wire is like the pipe and a bulb or motor is like the water wheel that uses the energy.
-
2. A cell of e.m.f. 1.5 V drives 0.5 C of charge round a circuit. How much energy does it supply?
- 3 J
- 0.75 J
- 2 J
- 0.33 J
Show answer
Answer: B. W = εq = 1.5 × 0.5 = 0.75 J. Dividing 1.5 by 0.5 gives 3, which is not energy.
-
3. How is a voltmeter connected to measure the p.d. across a bulb?
- In parallel, across the bulb
- In series with the bulb
- Between the cell and the switch only
- It needs no connection
Show answer
Answer: A. A voltmeter compares the potential at two points, so it is connected across (in parallel with) the component, red terminal to the positive side.
-
4. A current of 0.25 A flows through a resistor when the p.d. across it is 5 V. What is its resistance?
- 1.25 Ω
- 0.05 Ω
- 20 Ω
- 5.25 Ω
Show answer
Answer: C. R = V/I = 5 ÷ 0.25 = 20 Ω. Multiplying V and I gives 1.25, which is not resistance.
-
5. The resistance of a wire depends on
- its temperature only
- its material only
- its length and thickness only
- its material, its shape and size, and its temperature
Show answer
Answer: D. Resistance depends on what the wire is made of, its geometry (length and thickness) and its temperature, so all of these together.
Sign in to keep track of the lessons you finish.