- Practice
- About 17 min
- 5 practice questions
Effects of electric current, ac and dc, and electrical safety
Describe the heating, chemical and magnetic effects of current, compare direct and alternating current with their uses and advantages, and follow safety rules with electricity.
If something looks wrong, please tell us.
By the end of this lesson you can
- Explain the heating (Joule) effect and its uses.
- Describe electrolysis and electroplating as chemical effects.
- State the magnetic effect of current.
- Compare dc and ac, including the rectifier and inverter.
- List the dangers of electricity and the precautions to take.
When a current flows it does useful things: it heats a water heater, coats a spoon with metal and turns a motor. The three main effects are the heating, chemical and magnetic effects. Safety first: every experiment in this lesson uses a small dc cell or battery of about 9 V or less, never the 220 V ac mains supply at home, which can give a dangerous, even fatal, shock.
Heating effect
Electrons moving through a wire or resistor meet resistance. Work done against it turns electrical energy into heat. This is called Joule heating, after the scientist James Prescott Joule, who studied it. It is the principle of the electric iron, water heater, toaster and immersion heater, which use high-resistance elements such as nichrome. Even connecting wires have a little resistance, so appliances and wires become warm in use. Your teacher may show this by touching two wires from a 9 V battery to a narrow strip of aluminium foil on a wooden board: the thin tip gets hot enough to melt. Do not hold the foil, and do not leave the battery connected.
Chemical effect
Current can also pass through certain solutions. Conducting current through a solution is called electrolysis; the solution is the electrolyte. Here the current is carried by both electrons (in the wires) and ions (in the solution). The electrode joined to the positive terminal is the anode; the one joined to the negative terminal is the cathode. In a copper sulphate solution, with a cleaned copper strip as anode and a carbon rod (from a used dry cell) as cathode, connected to a small cell, a thin layer of copper slowly forms on the carbon rod. Coating one material with a metal this way is electroplating. Do this only with a teacher or adult: copper sulphate is harmful if swallowed and irritates skin and eyes, so wear gloves and wash your hands afterwards.
Magnetic effect
A wire carrying current produces a magnetic field around it, in circles perpendicular to the current. If the thumb of the right hand points along the current, the curled fingers show the direction of the magnetic field (the right-hand thumb rule). Oersted's discovery of this effect and its uses are studied in the next unit, Magnetism and Electromagnetism.
Effects of electric current
-
Heating effect
- Electric iron
- Water heater
- Toaster
-
Chemical effect
- Electrolysis
- Electroplating
- Electro-refining of metals
-
Magnetic effect
- Electromagnets
- Electric bell
- Motors
Direct current and alternating current
Direct current (dc) flows in one direction only; on a current-time graph it is a flat line. Cells, batteries, solar cells and thermocouples give dc, and cell phones, radios, electronic keyboards and electric vehicles run on it. Alternating current (ac) reverses its direction again and again, rising and falling smoothly with time, so the electrons move to and fro. The number of complete cycles per second is its frequency, measured in hertz (Hz). Household supply is ac; the textbook gives the Indian domestic supply as 220 V at 50 Hz, and that of the USA as 110 V at 60 Hz.
A rectifier (battery eliminator or dc adaptor) converts ac to dc; an inverter converts dc to ac.
ac and dc
-
Alternating current (ac)
- Direction reverses regularly
- Voltage changed easily by transformers
- Sent over long distances with little loss
- Easier to generate; easily changed to dc
-
Direct current (dc)
- Flows one way only
- Needed for electroplating and electro-refining
- Can be stored in cells and batteries
- From cells, batteries, solar cells
Worked example 1: charge through a bulb
Question: A bulb draws 2.5 A for 2 hours. How much charge flows through its filament? Working: t = 2 × 3600 = 7200 s. q = It = 2.5 × 7200 = 18 000 C.
Worked example 2: can ac electroplate?
Question: Why cannot ac be used for electroplating? Working: Plating needs metal ions to move steadily towards one electrode, the cathode. With ac the electrodes swap roles 50 times a second, so whatever is deposited in one half-cycle tends to be removed in the next. A steady one-way current, dc, is needed.
Dangers of electricity and precautions
- Damaged insulation: never touch bare wires; electricians wear insulating gloves and stand on a dry insulating mat or rubber footwear.
- Overloading: do not plug too many appliances into one socket; it can overheat the wiring and start a fire.
- Wrong points: use each appliance on a socket of the right rating, such as the separate points for an air conditioner or microwave oven.
- Moisture: keep switches and appliances dry; water lets current leak and can cause shocks. Never touch switches with wet hands.
- Children: keep sockets out of reach of small children or covered with safety shutters.
- Never experiment with mains electricity. The human body, being mostly water, conducts electricity, especially when wet.
A bird sitting on a single overhead wire is safe because both its feet are on the same wire at almost the same potential, so there is no potential difference to drive a current through its body. A person on the ground touching a live wire completes a path to earth and gets a shock.
Heating (Joule), chemical (electrolysis, electroplating) and magnetic effects. dc flows one way; ac reverses. Rectifier: ac to dc; inverter: dc to ac. Experiments only with small cells, never mains.
Key takeaways: current heats resistors, drives chemical changes in electrolytes and produces magnetic fields. ac is easy to transform and transmit; dc is needed for plating and storage. Respect electricity: dry hands, good insulation, no overloading and no experiments with the mains.
Check your understanding
-
1. The heating effect of electric current is also called
- Coulomb heating
- Joule heating
- Voltage heating
- Ampere heating
Show answer
Answer: B. The conversion of electrical energy into heat in a resistance is called Joule heating, after James Prescott Joule, who studied it.
-
2. Electroplating is an example of which effect of current?
- Heating effect
- Magnetic effect
- Chemical effect
- Lighting effect
Show answer
Answer: C. Electroplating deposits metal from an electrolyte onto the cathode by electrolysis, which is a chemical effect of current.
-
3. In an electrolyte such as copper sulphate solution, the current is carried by
- ions in the solution, along with electrons in the wires
- electrons only
- neutrons
- nothing; it does not conduct
Show answer
Answer: A. In the outer wires electrons carry the current; in the solution charged ions move. So both electrons and ions are involved in conduction through an electrolyte.
-
4. Which device converts ac into dc?
- Inverter
- Transformer
- Fuse
- Rectifier
Show answer
Answer: D. A rectifier (battery eliminator, dc adaptor) changes ac to dc. An inverter does the opposite, and a transformer changes the voltage of ac.
-
5. Which is an advantage of ac over dc?
- ac can be stored in batteries
- ac voltage can easily be stepped up or down with a transformer
- ac is needed for electroplating
- ac flows in one direction only
Show answer
Answer: B. Transformers work only with ac, so its voltage can be raised for long-distance transmission and lowered for homes. Storage, electroplating and one-way flow belong to dc.
Sign in to keep track of the lessons you finish.