Revision notes

Chapter 8 Mechanical Properties of Solids: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Elasticity, stress and strain

Stress = F/A. SI unit: N m⁻², called the pascal (Pa). Dimensions: [ML⁻¹T⁻²], the same as pressure.

Types of stress and the strain each produces

  • Longitudinal stress
    • Tensile (stretching) or compressive (squeezing)
    • Forces normal to the cross-section
    • Strain = ΔL/L
    • Length changes
  • Shearing stress
    • Forces parallel to opposite faces
    • Strain = Δx/L = tan θ ≈ θ
    • Shape changes, volume does not
  • Hydraulic stress
    • Equal normal force per unit area all over the surface
    • Strain = ΔV/V
    • Volume changes, shape does not
Strain at a glance
Kind of strainFormulaWhat changesUnit
LongitudinalΔL/LLengthNone
ShearingΔx/L = tan θShapeNone (θ in radians)
VolumeΔV/VVolumeNone
  • Elastic bodies recover their shape when the force is removed; plastic bodies do not.
  • Stress = restoring force per unit area, in N m⁻² (Pa), dimensions [ML⁻¹T⁻²].
  • Strain is a ratio, so it has no unit: ΔL/L, Δx/L (= tan θ ≈ θ) or ΔV/V.
  • Longitudinal stress changes length, shearing stress changes shape, hydraulic stress changes volume only.
Read the full lesson

Lesson 2

Hooke's law and the stress-strain curve

Hooke's law: within the proportional limit, stress ∝ strain, so stress = modulus of elasticity × strain.

Stages of a metal wire under increasing tensile stress

  1. O to A: proportional Straight line; Hooke's law holds; full recovery.
  2. A to B: elastic, not linear Still recovers fully; B is the yield point (elastic limit).
  3. B to D: plastic Large strain for small stress; unloading leaves a permanent set.
  4. D: ultimate tensile strength Maximum stress the material can bear.
  5. E: fracture The wire breaks.

Three kinds of stress-strain behaviour

  • Ductile
    • Long plastic region
    • D and E far apart
    • Can be drawn into wires
    • Example: copper
  • Brittle
    • Little or no plastic region
    • D and E close together
    • Snaps suddenly
    • Example: glass
  • Elastomer
    • Very large elastic strain
    • Curve not linear over most of the range
    • No clear plastic region
    • Example: rubber
  • Hooke's law (stress ∝ strain) holds only in the straight, proportional part of the curve.
  • Beyond the yield point (elastic limit) unloading leaves a permanent set.
  • Ultimate tensile strength is the greatest stress the material can bear; fracture follows.
  • Ductile: D and E far apart. Brittle: D and E close. Elastomers stretch hugely without obeying Hooke's law.
Read the full lesson

Lesson 3

Young's modulus and stretching of wires

Y = (F × L)/(A × ΔL) and ΔL = FL/(AY). Unit of Y: N m⁻² (Pa); dimensions [ML⁻¹T⁻²].

Approximate Young's moduli (standard textbook values)
MaterialY (N m⁻²)
Steel2.0 × 10¹¹
Copper1.1 × 10¹¹
Aluminium7.0 × 10¹⁰
Bone (compression)9.4 × 10⁹

Method for any stretching problem

  1. Find the force Tension in the wire, e.g. F = mg for a hanging load.
  2. Convert to SI mm² to m² (× 10⁻⁶), mm to m (× 10⁻³).
  3. Find the area A = πr² = πd²/4 for a round wire.
  4. Apply ΔL = FL/(AY) Then strain = ΔL/L and stress = F/A.
  • Y = stress/strain = FL/(AΔL); it depends only on the material.
  • Extension ΔL ∝ F × L/(d² × Y).
  • Wires in series carry the same tension; each stretches by FL/(AY) and the extensions add.
  • A larger Y means less stretch for the same stress: steel is more elastic than rubber or copper.
Read the full lesson

Lesson 4

Shear modulus, bulk modulus and Poisson's ratio

G = (F/A)/(Δx/L) = FL/(AΔx) = F/(Aθ). Shearing stress σs = Gθ. Unit: N m⁻² (Pa).

The three elastic moduli

  • Young's modulus Y
    • Tensile or compressive stress
    • Strain ΔL/L
    • Changes length
    • Solids only
  • Shear modulus G
    • Tangential stress
    • Strain θ = Δx/L
    • Changes shape, not volume
    • Solids only
  • Bulk modulus B
    • Hydraulic stress (pressure)
    • Strain ΔV/V
    • Changes volume, not shape
    • Solids, liquids and gases
  • G = F/(Aθ); usually G ≈ Y/3; shear is possible only in solids.
  • B = −p/(ΔV/V) is positive because pressure up means volume down; compressibility k = 1/B.
  • Solids are least compressible, gases most.
  • Poisson's ratio = lateral strain/longitudinal strain, a pure number (about 0.3 for steel).
Read the full lesson

Lesson 5

Elastic potential energy and uses of elasticity

Elastic potential energy U = ½ F l = ½ × stress × strain × volume. Energy per unit volume u = ½ σε = ½ Yε² = σ²/(2Y).

Designing a beam that does not sag

  • Choose material
    • Large Young's modulus Y
  • Choose dimensions
    • Short span l (δ ∝ l³)
    • Greater depth d (δ ∝ 1/d³)
    • Breadth b matters less (δ ∝ 1/b)
  • Choose shape
    • Deep thin bars can buckle
    • I-section: wide flanges, tall web
    • Less weight and cost, same strength
  • U = ½ F l = ½ × stress × strain × volume; per unit volume u = ½σε.
  • Safe rope area: A ≥ Mg/σy, then add a large safety factor; ropes are braided from thin wires.
  • Beam sag δ = Wl³/(4bd³Y): depth matters most; the I-section avoids buckling and saves material.
  • The elastic limit of rock limits mountains to roughly 10 km.
Read the full lesson

Privacy · Terms · Refunds · Delivery