- Foundation
- About 20 min
- 5 practice questions
Shear modulus, bulk modulus and Poisson's ratio
Define the shear modulus, bulk modulus, compressibility and Poisson's ratio, use them in calculations, and explain why solids are least and gases most compressible.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define the shear modulus G and use G = F/(Aθ).
- Define the bulk modulus B = −p/(ΔV/V) and explain its negative sign.
- Define compressibility and compare solids, liquids and gases.
- Define Poisson's ratio and use it to find a change in diameter.
Young's modulus deals with change of length. Two more moduli describe the other two kinds of deformation from lesson 1: change of shape (shear) and change of volume (hydraulic compression). A fourth constant, Poisson's ratio, links the stretching of a wire to its thinning.
Shear modulus (modulus of rigidity)
The ratio of shearing stress to shearing strain is the shear modulus G, also called the modulus of rigidity. With a tangential force F on a face of area A, a sideways displacement Δx over a height L and a small angle θ:
G = (F/A)/(Δx/L) = FL/(AΔx) = F/(Aθ). Shearing stress σs = Gθ. Unit: N m⁻² (Pa).
The shear modulus of most materials is smaller than their Young's modulus; for many materials G ≈ Y/3. For example, standard values are about 84 GPa for steel and 25 GPa for aluminium (1 GPa = 10⁹ Pa). Shear is possible only in solids, because only a solid resists a change of shape.
Bulk modulus and compressibility
When a body is placed in a fluid and the pressure on it rises by p, its volume falls by ΔV. The bulk modulus B is the ratio of hydraulic stress to volume strain: B = −p/(ΔV/V). Sign convention: an increase in pressure (p positive) produces a decrease in volume (ΔV negative), so the minus sign makes B a positive number. The unit of B is N m⁻² (Pa).
The reciprocal of the bulk modulus is the compressibility k: k = 1/B = −(1/Δp) × (ΔV/V), the fractional decrease in volume per unit increase in pressure. Its unit is Pa⁻¹ (m² N⁻¹). Solids have the largest bulk moduli, liquids smaller and gases very much smaller (standard values: steel about 1.6 × 10¹¹ Pa, water about 2.2 × 10⁹ Pa, air at STP about 1.0 × 10⁵ Pa). So gases are roughly a million times more compressible than solids. The reason is the coupling between neighbouring particles: strong in solids, weaker in liquids and very weak in gases. Bulk modulus is the only one of the three moduli that applies to solids, liquids and gases.
The three elastic moduli
-
Young's modulus Y
- Tensile or compressive stress
- Strain ΔL/L
- Changes length
- Solids only
-
Shear modulus G
- Tangential stress
- Strain θ = Δx/L
- Changes shape, not volume
- Solids only
-
Bulk modulus B
- Hydraulic stress (pressure)
- Strain ΔV/V
- Changes volume, not shape
- Solids, liquids and gases
Poisson's ratio
When a wire is stretched it also becomes slightly thinner. The strain perpendicular to the applied force is the lateral strain, Δd/d. Within the elastic limit the lateral strain is proportional to the longitudinal strain, and their ratio is Poisson's ratio: (Δd/d)/(ΔL/L). Being a ratio of two strains it has no unit or dimensions, and it depends only on the material: about 0.28 to 0.30 for steels and about 0.33 for aluminium alloys.
Worked example 1: shear of an aluminium cube
An aluminium cube of edge 10 cm has its lower face fixed. A tangential force of 1.0 × 10⁴ N acts on the upper face. Take G = 25 GPa = 2.5 × 10¹⁰ Pa. Find the shear angle and the sideways displacement of the upper face. Area: A = 0.10 × 0.10 = 1.0 × 10⁻² m². Shearing stress: F/A = 1.0 × 10⁴/1.0 × 10⁻² = 1.0 × 10⁶ Pa. Angle: θ = stress/G = 1.0 × 10⁶/2.5 × 10¹⁰ = 4.0 × 10⁻⁵ rad. Displacement: Δx = θL = 4.0 × 10⁻⁵ × 0.10 = 4.0 × 10⁻⁶ m, only 4 micrometres.
Worked example 2: compressing water
By what fraction does water shrink when the pressure on it rises by 1.1 × 10⁷ Pa? Take B = 2.2 × 10⁹ Pa. ΔV/V = −p/B = −(1.1 × 10⁷)/(2.2 × 10⁹) = −5.0 × 10⁻³, a decrease of 0.50%. One litre (1000 cm³) of water would lose 5.0 cm³. The minus sign only says the volume decreases.
Worked example 3: Poisson's ratio of a wire
A wire 1.0 m long and 2.0 mm in diameter is stretched by 1.0 mm, and its diameter decreases by 6.0 × 10⁻⁴ mm. Longitudinal strain = 1.0 mm/1000 mm = 1.0 × 10⁻³. Lateral strain = (6.0 × 10⁻⁴)/2.0 = 3.0 × 10⁻⁴. Poisson's ratio = (3.0 × 10⁻⁴)/(1.0 × 10⁻³) = 0.30, a value typical of steel.
Key takeaways
- G = F/(Aθ); usually G ≈ Y/3; shear is possible only in solids.
- B = −p/(ΔV/V) is positive because pressure up means volume down; compressibility k = 1/B.
- Solids are least compressible, gases most.
- Poisson's ratio = lateral strain/longitudinal strain, a pure number (about 0.3 for steel).
Check your understanding
-
1. A metal cube of edge 0.20 m has its base fixed. A tangential force of 4.0 × 10⁴ N on the top face shears it. If G = 2.5 × 10¹⁰ N m⁻², how far does the top face move sideways?
- 4.0 × 10⁻⁵ m
- 8.0 × 10⁻⁶ m
- 1.6 × 10⁻⁶ m
- 2.0 × 10⁻⁴ m
Show answer
Answer: B. A = 0.20 × 0.20 = 0.040 m². Shearing stress = 4.0 × 10⁴/0.040 = 1.0 × 10⁶ Pa. θ = stress/G = 1.0 × 10⁶/2.5 × 10¹⁰ = 4.0 × 10⁻⁵ rad (that is the angle, not the displacement). Δx = θL = 4.0 × 10⁻⁵ × 0.20 = 8.0 × 10⁻⁶ m.
-
2. Water (B = 2.2 × 10⁹ Pa) is subjected to an extra pressure of 2.2 × 10⁶ Pa. By what percentage does its volume decrease?
- 1.0%
- 10%
- 0.010%
- 0.10%
Show answer
Answer: D. ΔV/V = p/B = (2.2 × 10⁶)/(2.2 × 10⁹) = 1.0 × 10⁻³. As a percentage this is 1.0 × 10⁻³ × 100 = 0.10%.
-
3. Assertion (A): The bulk modulus is defined with a negative sign, B = −p/(ΔV/V). Reason (R): An increase in pressure produces a decrease in volume, and the sign makes B positive.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. When p is positive, ΔV is negative. Without the minus sign B would come out negative. The sign is put in precisely so that B is a positive quantity, so R correctly explains A.
-
4. A wire has Poisson's ratio 0.30. When its longitudinal strain is 2.0 × 10⁻³, what is its lateral strain?
- 6.0 × 10⁻⁴
- 6.7 × 10⁻³
- 1.5 × 10⁻⁴
- 2.3 × 10⁻³
Show answer
Answer: A. Poisson's ratio = lateral strain/longitudinal strain, so lateral strain = 0.30 × 2.0 × 10⁻³ = 6.0 × 10⁻⁴. The diameter decreases by this fraction.
-
5. Which elastic modulus can be defined for a gas?
- Young's modulus only
- Shear modulus only
- Bulk modulus only
- All three moduli
Show answer
Answer: C. A gas has no length or shape of its own, so Young's and shear moduli do not apply. It does change volume under pressure, so it has a bulk modulus (a small one, which is why gases are highly compressible).
Sign in to keep track of the lessons you finish.