• Foundation
  • About 20 min
  • 5 practice questions

Elastic potential energy and uses of elasticity

Derive the energy stored in a stretched wire, U = ½ × stress × strain × volume, and apply elasticity to crane ropes, beams, I-sections, pillars and the height of mountains.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Derive the work done in stretching a wire and the energy stored per unit volume.
  • Find the minimum thickness of a crane rope from its load and yield strength.
  • Use δ = Wl³/(4bd³Y) to explain why beams are deep and shaped like an I.
  • Estimate the greatest possible height of a mountain from the elastic limit of rock.

Stretching a wire takes work, because the atoms must be pulled apart against their attractions. That work is not lost: it is stored as elastic potential energy, which is why a stretched catapult can launch a stone. The same ideas, together with yield strength and Young's modulus, explain why cranes use braided ropes and bridges use I-shaped girders.

Energy stored in a stretched wire

Take a wire of length L, cross-sectional area A and Young's modulus Y. When it has been stretched by an amount l, Hooke's law gives the force needed as F = YA(l/L). The force is not constant: it grows from zero as the wire stretches.

  1. For a further tiny extension dl, the work done is dW = F dl = (YA l/L) dl.
  2. Total work from l = 0 to l: W = ∫ (YA/L) l dl = (YA/L) × l²/2 = ½ (YA l/L) × l.
  3. Since YA l/L is the final force F, W = ½ F l (the average force ½F times the extension).
  4. Rewrite: W = ½ × Y × (l/L)² × (A L) = ½ × Young's modulus × strain² × volume.
  5. Because stress = Y × strain: W = ½ × stress × strain × volume.

Elastic potential energy U = ½ F l = ½ × stress × strain × volume. Energy per unit volume u = ½ σε = ½ Yε² = σ²/(2Y).

Worked example 1: energy in a steel wire

A steel wire 2.0 m long with cross-sectional area 1.0 mm² is stretched by 1.0 mm. Take Y = 2.0 × 10¹¹ N m⁻². Force needed: F = YA l/L = 2.0 × 10¹¹ × 1.0 × 10⁻⁶ × 1.0 × 10⁻³/2.0 = 100 N. Energy stored: U = ½ F l = ½ × 100 × 1.0 × 10⁻³ = 0.050 J. Check by energy density: strain = 1.0 × 10⁻³/2.0 = 5.0 × 10⁻⁴; u = ½ Yε² = ½ × 2.0 × 10¹¹ × (5.0 × 10⁻⁴)² = 2.5 × 10⁴ J m⁻³; volume = AL = 2.0 × 10⁻⁶ m³; U = 2.5 × 10⁴ × 2.0 × 10⁻⁶ = 0.050 J. Both methods agree.

How thick should a crane rope be?

A crane rope must never be stretched beyond its elastic limit, or it would be permanently deformed. So the stress Mg/A must stay below the yield strength σy, giving A ≥ Mg/σy. In practice a large margin of safety, about a factor of ten in the load, is added. A single steel rod that thick would be stiff and hard to wind, so crane ropes are made of many thin wires braided together, which is easier to manufacture and gives flexibility as well as strength.

Worked example 2: a 5-tonne crane

A crane must lift 5000 kg. Mild steel has a yield strength of about 3.0 × 10⁸ N m⁻²; take g = 9.8 m s⁻². Minimum area: A = Mg/σy = (5000 × 9.8)/(3.0 × 10⁸) = 1.63 × 10⁻⁴ m². Radius: r = √(A/π) = √(5.2 × 10⁻⁵) ≈ 7.2 × 10⁻³ m, about 7 mm. With a safety factor of ten the area becomes 1.63 × 10⁻³ m² and r ≈ 2.3 cm.

Beams, buckling and pillars

A bar of length l, breadth b and depth d, supported near its ends and loaded with W at the centre, sags by δ = Wl³/(4bd³Y). To reduce sagging use a material with a large Y, keep the span l short and, above all, increase the depth: δ falls as 1/d³ but only as 1/b. A very deep, thin bar, however, can bend sideways or twist under a load that is not exactly central (on a bridge the traffic moves), which is called buckling. The I-section is the compromise: wide flanges give a large load-bearing surface, and a tall web gives depth to resist bending, while removing metal where it does little work. This keeps the beam light and cheap without losing strength. Similarly, a pillar with broadened (distributed) ends carries more load than one with rounded ends.

Designing a beam that does not sag

  • Choose material
    • Large Young's modulus Y
  • Choose dimensions
    • Short span l (δ ∝ l³)
    • Greater depth d (δ ∝ 1/d³)
    • Breadth b matters less (δ ∝ 1/b)
  • Choose shape
    • Deep thin bars can buckle
    • I-section: wide flanges, tall web
    • Less weight and cost, same strength

Worked example 3: changing the depth of a beam

A rectangular beam is replaced by one of the same material, length and breadth but twice the depth. By what factor does the central sag change for the same load? δ ∝ 1/d³, so δ(new)/δ(old) = 1/2³ = 1/8. Doubling the breadth instead would only halve the sag.

How high can a mountain be?

At the base of a mountain of height h the force per unit area due to the rock above is about hρg. The sides of the mountain are free, so this is not uniform compression; there is a shearing component of roughly hρg. If it exceeds the elastic limit of rock, the rock at the base flows. Taking an elastic limit of about 3.0 × 10⁸ N m⁻², ρ = 3.0 × 10³ kg m⁻³ and g = 10 m s⁻²: h = 3.0 × 10⁸/(3.0 × 10³ × 10) = 1.0 × 10⁴ m = 10 km. This rough estimate is a little more than the height of the highest mountains on Earth.

Key takeaways

  • U = ½ F l = ½ × stress × strain × volume; per unit volume u = ½σε.
  • Safe rope area: A ≥ Mg/σy, then add a large safety factor; ropes are braided from thin wires.
  • Beam sag δ = Wl³/(4bd³Y): depth matters most; the I-section avoids buckling and saves material.
  • The elastic limit of rock limits mountains to roughly 10 km.

Check your understanding

  1. 1. A wire obeying Hooke's law is stretched by 2.0 mm by a final force of 200 N. How much elastic potential energy does it store?

    1. 0.40 J
    2. 0.20 J
    3. 400 J
    4. 0.10 J
    Show answer

    Answer: B. The force rises steadily from 0 to 200 N, so U = ½ F l = ½ × 200 × 2.0 × 10⁻³ = 0.20 J. Using F × l without the half would double-count and give 0.40 J.

  2. 2. A wire is under a stress of 2.0 × 10⁸ N m⁻² and a strain of 1.0 × 10⁻³. What is the elastic energy stored per unit volume?

    1. 2.0 × 10⁵ J m⁻³
    2. 5.0 × 10⁴ J m⁻³
    3. 2.0 × 10¹¹ J m⁻³
    4. 1.0 × 10⁵ J m⁻³
    Show answer

    Answer: D. u = ½ × stress × strain = ½ × 2.0 × 10⁸ × 1.0 × 10⁻³ = 1.0 × 10⁵ J m⁻³.

  3. 3. A beam is supported at its ends and loaded at the centre. If its depth is doubled, keeping everything else the same, the sag becomes

    1. half
    2. one quarter
    3. one eighth
    4. twice as large
    Show answer

    Answer: C. δ = Wl³/(4bd³Y), so δ ∝ 1/d³. Doubling d divides the sag by 2³ = 8.

  4. 4. A crane rope of mild steel (yield strength 3.0 × 10⁸ N m⁻²) must hold 3000 kg without permanent stretch. Taking g = 9.8 m s⁻² and no safety margin, what is the least cross-sectional area?

    1. 1.0 × 10⁻⁵ m²
    2. 9.8 × 10⁻⁵ m²
    3. 3.3 × 10⁻⁴ m²
    4. 2.9 × 10⁻³ m²
    Show answer

    Answer: B. A ≥ Mg/σy = (3000 × 9.8)/(3.0 × 10⁸) = 29400/(3.0 × 10⁸) = 9.8 × 10⁻⁵ m². A real crane would use about ten times this area as a safety margin.

  5. 5. Why are girders for bridges and buildings commonly made with an I-shaped cross-section?

    1. It gives depth to resist bending and a wide load-bearing surface while using less material, and it resists buckling better than a thin deep bar
    2. It is the only shape steel can be rolled into
    3. It increases the Young's modulus of steel
    4. It makes the beam bend more so it can absorb shocks
    Show answer

    Answer: A. Sag falls steeply with depth (δ ∝ 1/d³), but a thin deep bar can buckle. The I-section keeps the depth, adds wide flanges to bear the load and removes metal where it does little work, cutting weight and cost. The shape does not change Y, which is a property of the material.

Privacy · Terms · Refunds · Delivery