• Foundation
  • About 18 min
  • 5 practice questions

Hooke's law and the stress-strain curve

State Hooke's law and its limit, read a stress-strain curve for a metal (proportional limit, yield point, permanent set, ultimate strength, fracture) and tell ductile, brittle and elastomeric materials apart.

If something looks wrong, please tell us.

By the end of this lesson you can

  • State Hooke's law and the condition under which it holds.
  • Name each region and point of a typical stress-strain curve for a metal.
  • Explain permanent set, yield strength and ultimate tensile strength.
  • Classify a material as ductile, brittle or an elastomer from its curve.

Knowing stress and strain separately is not enough; we need to know how one depends on the other. For small deformations the answer is wonderfully simple, and that simple rule is what allows engineers to predict how much a beam will bend or a cable will stretch. For larger loads the rule breaks down, and a stress-strain graph shows exactly where.

Hooke's law

Experiments show that for small deformations, stress is directly proportional to strain. This is Hooke's law. Writing it as an equation, stress = k × strain, where the constant k is called the modulus of elasticity. Since strain has no unit, the modulus has the same unit as stress, N m⁻² or Pa. Hooke's law is an empirical law: it is found from experiment, it works for most materials, and some materials (such as rubber) do not follow it.

Hooke's law: within the proportional limit, stress ∝ strain, so stress = modulus of elasticity × strain.

Reading the stress-strain curve of a metal

In a tensile test a wire or test rod is stretched by a force increased in small steps; the stress (force per unit area) and the strain are recorded at each step and plotted with strain on the x-axis and stress on the y-axis. A typical metal gives a curve with these features.

  1. O to A (proportional region): the graph is a straight line through the origin. Hooke's law holds and the slope is the modulus. Remove the load and the wire returns to its original length.
  2. A to B: stress and strain are no longer proportional, but the wire still recovers fully when unloaded. B is the yield point (also called the elastic limit); the stress there is the yield strength σy.
  3. B to D (plastic region): strain grows quickly for small increases in stress. If the load is removed at a point C in this region, the wire does not return to zero strain: it keeps a permanent set. This is plastic deformation.
  4. D: the highest stress the material can bear, the ultimate tensile strength σu.
  5. D to E: beyond D the wire thins at one place and extra strain occurs even for a reduced force, until it fractures at E.

Stages of a metal wire under increasing tensile stress

  1. O to A: proportional Straight line; Hooke's law holds; full recovery.
  2. A to B: elastic, not linear Still recovers fully; B is the yield point (elastic limit).
  3. B to D: plastic Large strain for small stress; unloading leaves a permanent set.
  4. D: ultimate tensile strength Maximum stress the material can bear.
  5. E: fracture The wire breaks.

Ductile, brittle and elastomeric materials

If D and E are far apart, the material can be drawn out a great deal before breaking: it is ductile (copper, mild steel, brass). If D and E are close together, it breaks almost as soon as it stops behaving elastically: it is brittle (glass, cast iron). Some materials, such as rubber and the elastic tissue of the aorta (the large artery leaving the heart), can be stretched to very large strains and still recover. Their elastic region is huge, yet the curve is not a straight line over most of it and there is no well-defined plastic region. Such materials are called elastomers.

Three kinds of stress-strain behaviour

  • Ductile
    • Long plastic region
    • D and E far apart
    • Can be drawn into wires
    • Example: copper
  • Brittle
    • Little or no plastic region
    • D and E close together
    • Snaps suddenly
    • Example: glass
  • Elastomer
    • Very large elastic strain
    • Curve not linear over most of the range
    • No clear plastic region
    • Example: rubber

Worked example 1: using Hooke's law

In the straight part of its curve, a stress of 2.0 × 10⁸ N m⁻² produces a strain of 1.0 × 10⁻³ in a wire. (a) Find the modulus. (b) Find the strain for a stress of 1.0 × 10⁸ N m⁻². (a) Modulus = stress/strain = (2.0 × 10⁸)/(1.0 × 10⁻³) = 2.0 × 10¹¹ N m⁻². (b) In the proportional region strain is proportional to stress, so halving the stress halves the strain: strain = (1.0 × 10⁸)/(2.0 × 10¹¹) = 5.0 × 10⁻⁴.

Worked example 2: reading a curve (made-up test data)

A test on a metal sample (made-up practice data) gives: the curve is straight up to stress 250 MPa at strain 0.00125; the yield point is at 300 MPa; the highest stress reached is 400 MPa; the sample breaks at 380 MPa at a strain of 0.25. Modulus = 250 × 10⁶/0.00125 = 2.0 × 10¹¹ Pa. Yield strength = 300 MPa. Ultimate tensile strength = 400 MPa. Because the strain at fracture (0.25) is about 200 times the strain at the end of the straight part, the fracture point lies far from the ultimate point: the material is ductile.

Worked example 3: the largest safe load

A wire of cross-sectional area 1.0 mm² is made of a metal of yield strength 2.5 × 10⁸ N m⁻². What is the largest load it can carry without a permanent set? The stress must not exceed σy, so F = σy × A = 2.5 × 10⁸ × 1.0 × 10⁻⁶ = 250 N.

Key takeaways

  • Hooke's law (stress ∝ strain) holds only in the straight, proportional part of the curve.
  • Beyond the yield point (elastic limit) unloading leaves a permanent set.
  • Ultimate tensile strength is the greatest stress the material can bear; fracture follows.
  • Ductile: D and E far apart. Brittle: D and E close. Elastomers stretch hugely without obeying Hooke's law.

Check your understanding

  1. 1. In which part of a metal's stress-strain curve is Hooke's law obeyed?

    1. Only between the yield point and the ultimate tensile strength
    2. Only in the straight portion starting at the origin
    3. Over the whole curve up to fracture
    4. Only beyond the ultimate tensile strength
    Show answer

    Answer: B. Hooke's law says stress is proportional to strain. That is true only where the graph is a straight line through the origin, the proportional region O to A. Beyond it the curve bends, even though recovery is still complete up to the yield point.

  2. 2. A wire is loaded until it is in the plastic region and the load is then removed. What happens?

    1. It returns exactly to its original length
    2. It breaks immediately
    3. It keeps some extension, called a permanent set
    4. Its length becomes less than the original length
    Show answer

    Answer: C. Beyond the yield point the deformation is plastic. When the stress is brought back to zero the strain does not return to zero, so the wire stays longer than before: a permanent set.

  3. 3. For a certain material the ultimate tensile strength and the fracture point lie very close together on the stress-strain curve. The material is best described as

    1. ductile
    2. an elastomer
    3. perfectly plastic
    4. brittle
    Show answer

    Answer: D. A brittle material breaks almost as soon as it passes its greatest stress, so D and E are close. A ductile material has D and E far apart; an elastomer shows a very large elastic region.

  4. 4. In the straight part of its curve, a stress of 1.5 × 10⁸ N m⁻² produces a strain of 7.5 × 10⁻⁴ in a wire. What is the modulus of elasticity?

    1. 1.1 × 10¹¹ N m⁻²
    2. 5.0 × 10⁻¹² N m⁻²
    3. 2.0 × 10¹¹ N m⁻²
    4. 2.0 × 10⁸ N m⁻²
    Show answer

    Answer: C. Modulus = stress/strain = (1.5 × 10⁸)/(7.5 × 10⁻⁴) = 0.2 × 10¹² = 2.0 × 10¹¹ N m⁻². Dividing the other way round gives a meaningless tiny number.

  5. 5. Which statement about elastomers such as rubber is correct?

    1. They can undergo very large strains and still recover, without obeying Hooke's law over most of the range
    2. They have no elastic region at all
    3. They obey Hooke's law exactly up to fracture
    4. They have a larger Young's modulus than steel
    Show answer

    Answer: A. Elastomers stretch to several times their length and recover, so their elastic region is very large, but the stress-strain graph is curved over most of it and has no clear plastic region. Their modulus is far smaller than that of steel.

Privacy · Terms · Refunds · Delivery