- Foundation
- About 18 min
- 5 practice questions
Elasticity, stress and strain
Define elasticity and plasticity, calculate stress and strain, and tell apart longitudinal, shearing and hydraulic (volume) deformation with their SI units and dimensions.
If something looks wrong, please tell us.
By the end of this lesson you can
- Explain the difference between an elastic and a plastic body.
- Define stress as restoring force per unit area and state its SI unit and dimensions.
- Name the three kinds of stress and the strain each one produces.
- Calculate longitudinal, shearing and volume strain from measured changes.
In mechanics we often treat a solid as rigid: its shape and size never change. Real solids are not like that. A steel bridge sags slightly under a lorry, a bone shortens a little when you stand, and a spring lengthens when pulled. Engineers who design buildings, cranes, aircraft and artificial limbs need to know exactly how much a material changes and how much load it can take. This chapter builds that knowledge, starting with two measurable quantities: stress and strain.
Elastic and plastic behaviour
Pull a spring gently and release it: it returns to its original length. The property of a body by which it tends to regain its original size and shape when the deforming force is removed is called elasticity, and the change it undergoes is an elastic deformation. Press a lump of wet clay or putty and it stays dented: it has no tendency to recover. Such bodies are called plastic, and the property is plasticity. Putty and mud come close to ideal plastic bodies, while no real solid is perfectly elastic for all loads.
Stress: restoring force per unit area
When a deforming force acts on a body that stays in equilibrium, the atoms are pushed or pulled from their normal positions and the body develops an internal restoring force, equal in magnitude and opposite in direction to the applied force. The restoring force per unit area is the stress. If a force F acts on a cross-section of area A, the magnitude of the stress is F/A.
Stress = F/A. SI unit: N m⁻², called the pascal (Pa). Dimensions: [ML⁻¹T⁻²], the same as pressure.
Strain is the fractional change in a dimension: change in size divided by original size. Because it is a ratio of two like quantities, strain has no unit and no dimensions.
Three ways a solid can be deformed
- Longitudinal (tensile or compressive) stress: equal and opposite forces act perpendicular to the end faces of a rod. Pulling gives tensile stress, pushing gives compressive stress. The length changes by ΔL, and the longitudinal strain = ΔL/L.
- Shearing (tangential) stress: equal and opposite forces act parallel to two opposite faces, so one face slides relative to the other by Δx. The shearing strain = Δx/L = tan θ, where θ is the angle through which the sides tilt. For small angles tan θ ≈ θ (in radians). Pushing the top cover of a thick book sideways while its bottom rests on a table is a good picture.
- Hydraulic stress: a body immersed in a fluid under pressure is pushed equally and perpendicularly at every point of its surface. Its volume decreases by ΔV but its shape does not change. The volume strain = ΔV/V, and the hydraulic stress equals the pressure in magnitude.
Types of stress and the strain each produces
-
Longitudinal stress
- Tensile (stretching) or compressive (squeezing)
- Forces normal to the cross-section
- Strain = ΔL/L
- Length changes
-
Shearing stress
- Forces parallel to opposite faces
- Strain = Δx/L = tan θ ≈ θ
- Shape changes, volume does not
-
Hydraulic stress
- Equal normal force per unit area all over the surface
- Strain = ΔV/V
- Volume changes, shape does not
| Kind of strain | Formula | What changes | Unit |
|---|---|---|---|
| Longitudinal | ΔL/L | Length | None |
| Shearing | Δx/L = tan θ | Shape | None (θ in radians) |
| Volume | ΔV/V | Volume | None |
Worked example 1: tensile stress and strain
A wire 2.0 m long with cross-sectional area 2.0 mm² hangs from a hook and carries a load of 100 N. It stretches by 0.50 mm. Find the stress and the strain. Step 1 (units): A = 2.0 mm² = 2.0 × 10⁻⁶ m²; ΔL = 0.50 mm = 5.0 × 10⁻⁴ m. Step 2 (stress): stress = F/A = 100/(2.0 × 10⁻⁶) = 5.0 × 10⁷ N m⁻². Step 3 (strain): strain = ΔL/L = (5.0 × 10⁻⁴)/2.0 = 2.5 × 10⁻⁴. Note that the tension at any cross-section is 100 N, not 200 N, even though the hook also pulls with 100 N: the stress is F/A.
Worked example 2: shearing strain
A rubber block 4.0 cm tall has a top face of 10 cm × 10 cm. A tangential force of 500 N on the top face, with the bottom face held fixed, moves the top face sideways by 2.0 mm. Shearing stress = F/A = 500/(0.10 × 0.10) = 5.0 × 10⁴ N m⁻². Shearing strain = Δx/L = 0.20 cm/4.0 cm = 0.050. So θ ≈ 0.050 rad, which is about 2.9°. The top face area, not the side area, is used because the force acts parallel to that face.
Worked example 3: volume strain
A metal sphere of volume 1000 cm³ is lowered into deep water and its volume decreases by 0.20 cm³. Volume strain = ΔV/V = 0.20/1000 = 2.0 × 10⁻⁴. The sphere stays a sphere: hydraulic stress changes size, not shape.
Key takeaways
- Elastic bodies recover their shape when the force is removed; plastic bodies do not.
- Stress = restoring force per unit area, in N m⁻² (Pa), dimensions [ML⁻¹T⁻²].
- Strain is a ratio, so it has no unit: ΔL/L, Δx/L (= tan θ ≈ θ) or ΔV/V.
- Longitudinal stress changes length, shearing stress changes shape, hydraulic stress changes volume only.
Check your understanding
-
1. What are the dimensions of stress?
- [MLT⁻²]
- [ML⁻¹T⁻²]
- [ML²T⁻²]
- Stress is dimensionless
Show answer
Answer: B. Stress = force/area. Force has dimensions [MLT⁻²] and area [L²], so stress has [MLT⁻²]/[L²] = [ML⁻¹T⁻²], the same as pressure. Force alone is [MLT⁻²] and energy is [ML²T⁻²]; it is strain, not stress, that is dimensionless.
-
2. A wire 4.0 m long is stretched by 2.0 mm. What is the longitudinal strain?
- 5.0 × 10⁻²
- 2.0 × 10⁻³
- 5.0 × 10⁻⁴
- 8.0 × 10⁻³
Show answer
Answer: C. Strain = ΔL/L = (2.0 × 10⁻³ m)/(4.0 m) = 5.0 × 10⁻⁴. Both lengths must be in the same unit before dividing; the result has no unit.
-
3. A small solid cube is lowered to the bottom of a deep lake. Which statement describes its deformation?
- Its shape changes but its volume does not
- Its length increases in the vertical direction only
- Its volume decreases but its shape stays the same
- It suffers pure shear
Show answer
Answer: C. The water pushes perpendicularly and equally on every part of the surface. This is hydraulic stress: it produces volume strain ΔV/V with no change of shape, so the cube stays a (slightly smaller) cube.
-
4. The top face of a block 10 cm tall moves 0.5 mm sideways relative to its fixed bottom face under a tangential force. What is the shearing strain?
- 0.05
- 0.005
- 0.5
- 5
Show answer
Answer: B. Shearing strain = Δx/L. Convert to the same unit: Δx = 0.5 mm = 0.05 cm, L = 10 cm. Strain = 0.05/10 = 0.005 (an angle of about 0.005 rad).
-
5. Assertion (A): Strain has no unit. Reason (R): Strain is the ratio of a change in a dimension to the original value of that dimension.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Strain is ΔL/L, Δx/L or ΔV/V: in each case two quantities of the same kind are divided, so the units cancel. R is true and is exactly why A is true.
Sign in to keep track of the lessons you finish.