- Foundation
- About 20 min
- 5 practice questions
Young's modulus and stretching of wires
Define Young's modulus, derive Y = FL/(AΔL), use standard values to find stress, extension and strain, and solve problems on wires of different length, thickness and material.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define Young's modulus and derive Y = FL/(AΔL).
- Calculate the extension of a wire from its length, area, load and Young's modulus.
- Compare extensions of wires that differ in length, diameter or material.
- Explain why steel is called 'more elastic' than rubber.
Every modulus of elasticity is a ratio stress/strain in the proportional region, and its value is a property of the material, not of the particular piece. The first and most used of these moduli describes stretching and squeezing along a length. It tells us, for example, how thick a steel rod must be so that it stretches by no more than a millimetre.
Definition and formula
Experiments show that for a given material the strain is the same for the same magnitude of tensile or compressive stress. Young's modulus Y is defined as the ratio of tensile (or compressive) stress σ to the longitudinal strain ε, within the proportional limit.
- Start from the definition: Y = σ/ε.
- Substitute σ = F/A (force normal to the cross-section of area A).
- Substitute ε = ΔL/L (extension divided by original length).
- So Y = (F/A)/(ΔL/L) = (F × L)/(A × ΔL).
- Rearranged for the extension: ΔL = (F × L)/(A × Y).
Y = (F × L)/(A × ΔL) and ΔL = FL/(AY). Unit of Y: N m⁻² (Pa); dimensions [ML⁻¹T⁻²].
For a round wire of radius r, A = πr². The extension therefore grows in proportion to the load F and the length L, and falls as 1/r² (that is, as 1/d² for diameter d). Doubling the diameter cuts the extension to one quarter.
| Material | Y (N m⁻²) |
|---|---|
| Steel | 2.0 × 10¹¹ |
| Copper | 1.1 × 10¹¹ |
| Aluminium | 7.0 × 10¹⁰ |
| Bone (compression) | 9.4 × 10⁹ |
Metals have large Young's moduli, so they need large forces for small changes in length. Steel needs a larger force than copper, brass or aluminium to produce the same strain in a wire of the same size, which is why it is used in heavy machines and structures. In everyday speech we call rubber 'very elastic' because it stretches a lot, but in physics a material that stretches less for a given stress has the larger modulus and is the more elastic one. Steel is far more elastic than rubber.
Worked example 1: extension of a steel wire
A steel wire 2.0 m long and 0.50 mm in radius carries a 10 kg load. Take g = 9.8 m s⁻² and Y = 2.0 × 10¹¹ N m⁻². Find the stress and the extension. Force: F = mg = 10 × 9.8 = 98 N. Area: A = πr² = 3.142 × (5.0 × 10⁻⁴)² = 7.85 × 10⁻⁷ m². Stress: F/A = 98/(7.85 × 10⁻⁷) = 1.25 × 10⁸ N m⁻². Extension: ΔL = FL/(AY) = (98 × 2.0)/(7.85 × 10⁻⁷ × 2.0 × 10¹¹) = 196/(1.57 × 10⁵) = 1.25 × 10⁻³ m, that is about 1.25 mm. Strain = 1.25 × 10⁻³/2.0 = 6.2 × 10⁻⁴.
Worked example 2: comparing two wires of the same material
Wire P has length L and diameter d. Wire Q, of the same material, has length 2L and diameter 2d. Both carry the same load. Find ΔL(P)/ΔL(Q). Since ΔL = FL/(AY) and A ∝ d², ΔL ∝ L/d². For P: L/d². For Q: 2L/(4d²) = L/(2d²). Ratio = (L/d²) ÷ (L/(2d²)) = 2. Wire P stretches twice as much, even though it is shorter, because it is thinner.
Worked example 3: two wires joined end to end
A copper wire and a steel wire, each 1.0 m long with cross-sectional area 1.0 mm², are joined end to end and hung from a support with a 110 N load at the bottom. Use Y(copper) = 1.1 × 10¹¹ and Y(steel) = 2.0 × 10¹¹ N m⁻². Both wires carry the same tension, 110 N (ignore their own weight). Copper: ΔL = (110 × 1.0)/(1.0 × 10⁻⁶ × 1.1 × 10¹¹) = 1.0 × 10⁻³ m. Steel: ΔL = (110 × 1.0)/(1.0 × 10⁻⁶ × 2.0 × 10¹¹) = 5.5 × 10⁻⁴ m. Total extension = 1.0 mm + 0.55 mm = 1.55 mm. The copper wire, with the smaller modulus, stretches more.
Method for any stretching problem
- Find the force Tension in the wire, e.g. F = mg for a hanging load.
- Convert to SI mm² to m² (× 10⁻⁶), mm to m (× 10⁻³).
- Find the area A = πr² = πd²/4 for a round wire.
- Apply ΔL = FL/(AY) Then strain = ΔL/L and stress = F/A.
Key takeaways
- Y = stress/strain = FL/(AΔL); it depends only on the material.
- Extension ΔL ∝ F × L/(d² × Y).
- Wires in series carry the same tension; each stretches by FL/(AY) and the extensions add.
- A larger Y means less stretch for the same stress: steel is more elastic than rubber or copper.
Check your understanding
-
1. A steel wire 2.0 m long with cross-sectional area 2.0 × 10⁻⁶ m² carries a tension of 400 N. Taking Y = 2.0 × 10¹¹ N m⁻², what is its extension?
- 0.2 mm
- 1.0 mm
- 2.0 mm
- 20 mm
Show answer
Answer: C. ΔL = FL/(AY) = (400 × 2.0)/(2.0 × 10⁻⁶ × 2.0 × 10¹¹) = 800/(4.0 × 10⁵) = 2.0 × 10⁻³ m = 2.0 mm.
-
2. Two wires of the same material and length carry the same load. The diameter of wire X is half that of wire Y. What is the ratio of the extension of X to that of Y?
- 1 : 2
- 2 : 1
- 1 : 4
- 4 : 1
Show answer
Answer: D. ΔL = FL/(AY) with A = πd²/4, so ΔL ∝ 1/d² when F, L and Y are the same. Halving d makes the area one quarter, so X stretches 4 times as much: the ratio is 4 : 1.
-
3. Wire P (length 2 m, area 1 mm²) and wire Q (length 1 m, area 2 mm²) stretch by the same amount under the same load. What is Y(P)/Y(Q)?
- 4
- 1
- 1/4
- 2
Show answer
Answer: A. Y = FL/(AΔL). With F and ΔL equal, Y ∝ L/A. For P: 2/1 = 2. For Q: 1/2 = 0.5. Ratio = 2/0.5 = 4.
-
4. Why is steel described in physics as more elastic than rubber?
- Steel stretches more than rubber for the same stress
- Steel has a much larger Young's modulus, so it deforms less for the same stress and recovers
- Rubber has no elastic region
- Steel is heavier than rubber
Show answer
Answer: B. Elasticity in physics is measured by the modulus. Steel needs a far larger stress to produce the same strain, so it has a larger Y and is the more elastic material. The everyday idea that 'stretches more' means 'more elastic' is a misnomer.
-
5. Assertion (A): Young's modulus is defined only for solids. Reason (R): Only solids have a definite length and shape that can be changed by a longitudinal stress.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Young's modulus relates a change of length to longitudinal stress. Liquids and gases have no fixed length or shape of their own, so only solids can have a Young's modulus. R gives the correct reason for A.
Sign in to keep track of the lessons you finish.