Revision notes

Chapter 9 Mechanical Properties of Fluids: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Pressure, Pascal's law and pressure at a depth

Average pressure P = F/A, where F is the normal force on area A. At a point, P = lim (ΔA → 0) ΔF/ΔA. SI unit: N m⁻² = pascal (Pa). Dimensions [ML⁻¹T⁻²]. Pressure is a scalar.

P = Pa + ρgh. The excess P − Pa = ρgh is the gauge pressure. The area and shape of the container do not appear.

From forces on a column to P = Pa + ρgh

  1. Fluid column at rest Area A, height h, density ρ.
  2. Balance vertical forces (P₂ − P₁)A = mg.
  3. Substitute m = ρAh P₂ − P₁ = ρgh.
  4. Top open to air P = Pa + ρgh at depth h.
  • A fluid at rest exerts force normal to every surface; pressure P = F/A is a scalar.
  • Pascal's law: pressure at a point acts equally in all directions and is equal at all points on one horizontal level.
  • P = Pa + ρgh; the shape of the vessel does not matter (hydrostatic paradox).
  • Gauge pressure = P − Pa = ρgh.
Read the full lesson

Lesson 2

Atmospheric pressure, gauges and hydraulic machines

Common pressure units
UnitValue in pascalWhere used
1 atm1.013 × 10⁵ PaPressure of the atmosphere at sea level
1 bar10⁵ PaMeteorology (also the millibar)
1 torr = 1 mm of Hgabout 133 PaMedicine and physiology, e.g. blood pressure

How a hydraulic lift multiplies force

  1. Small force F₁ on small piston A₁ Creates pressure P = F₁/A₁ in the liquid.
  2. Pressure transmitted undiminished Pascal's law: the same P everywhere in the liquid.
  3. Large piston A₂ pushed up F₂ = P × A₂ = F₁ × A₂/A₁.
  4. Distances trade off A₁d₁ = A₂d₂: the large piston moves less.
  • Barometer: Pa = ρgh; about 76 cm of mercury at sea level.
  • 1 atm = 1.013 × 10⁵ Pa, 1 bar = 10⁵ Pa, 1 torr = 1 mm of Hg ≈ 133 Pa.
  • Manometers, tyre gauges and blood-pressure gauges read gauge pressure, P − Pa.
  • Hydraulic lift: F₂ = F₁(A₂/A₁) and A₁d₁ = A₂d₂.
Read the full lesson

Lesson 3

Streamline flow, continuity and Bernoulli's principle

Streamline flow and turbulent flow

  • Streamline (steady) flow
    • Velocity at each point constant in time
    • Smooth paths that never cross
    • Low speeds, below the critical speed
    • Bernoulli's equation applies
  • Turbulent flow
    • Velocity at a point keeps fluctuating
    • Eddies and whirlpools
    • High speeds, above the critical speed
    • Bernoulli's equation does not apply

Equation of continuity: A₁v₁ = A₂v₂, i.e. Av = constant (the volume flow rate). Where the pipe narrows, the fluid speeds up.

Bernoulli's principle: along a streamline, P + ½ρv² + ρgh = constant. Each term is an energy per unit volume (unit J m⁻³ = Pa).

  • Streamlines show steady flow and never cross; above the critical speed flow is turbulent.
  • Continuity (mass conservation): A₁v₁ = A₂v₂ for an incompressible fluid.
  • Bernoulli (energy conservation): P + ½ρv² + ρgh is constant along a streamline.
  • It needs steady, incompressible, non-viscous flow; faster flow means lower pressure at the same height.
Read the full lesson

Lesson 4

Uses of Bernoulli's principle, viscosity and Stokes' law

Torricelli's law: v = √(2gh), the same speed a body gains in falling freely through height h.

A sphere falling through a viscous fluid

  1. Released from rest Weight exceeds buoyancy; it accelerates.
  2. Speed rises Viscous drag 6πηav grows with speed.
  3. Forces balance Drag + buoyancy = weight; acceleration becomes zero.
  4. Terminal velocity vt = 2a²(ρ − σ)g/(9η), constant from then on.
  • Torricelli: v = √(2gh) from an open tank.
  • Faster air on one side means lower pressure there: Magnus effect and wing lift.
  • η = (F/A)/(v/l), unit Pa s (poiseuille), dimensions [ML⁻¹T⁻¹]; falls with temperature for liquids, rises for gases.
  • Stokes: F = 6πηav; terminal velocity vt = 2a²(ρ − σ)g/(9η) ∝ a².
Read the full lesson

Lesson 5

Surface tension, drops, bubbles and capillary rise

Surface tension S = F/(2l) for a film (two surfaces) = surface energy per unit area. Unit N m⁻¹ or J m⁻².

Wetting and non-wetting liquids

  • Acute angle of contact
    • Liquid attracted strongly to the solid
    • Spreads and wets the surface
    • Concave meniscus; rises in a capillary
    • Water on clean glass
  • Obtuse angle of contact
    • Liquid attracted more to itself
    • Forms drops, does not wet
    • Convex meniscus; falls in a capillary
    • Mercury on glass, water on a lotus leaf

Capillary rise h = 2S cos θ/(ρga). The narrower the tube, the higher the rise; if θ is obtuse (mercury), cos θ < 0 and the liquid is depressed.

  • Surface molecules have extra energy; liquids minimise surface area, so free drops are spherical.
  • S = force per unit length = energy per unit area; a film has two surfaces (S = F/2l).
  • Acute θ: wets and rises; obtuse θ: forms beads and is depressed.
  • Excess pressure: drop or cavity 2S/r, soap bubble 4S/r; capillary rise h = 2S cos θ/(ρga).
Read the full lesson

Privacy · Terms · Refunds · Delivery