• Foundation
  • About 18 min
  • 5 practice questions

Pressure, Pascal's law and pressure at a depth

Define pressure and density, state Pascal's law, derive P = Pa + ρgh and use it to find pressure at a depth, and explain the hydrostatic paradox.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain what makes a fluid different from a solid.
  • Define pressure and density with their SI units and dimensions.
  • State Pascal's law and explain why pressure is the same at one level in a fluid at rest.
  • Derive and use P = Pa + ρgh, and explain the hydrostatic paradox.

Liquids and gases can flow, so together they are called fluids. A fluid has no shape of its own: it takes the shape of its container. Liquids have a nearly fixed volume and a free surface, while gases spread to fill all the space available and are far more compressible. The key mechanical difference from a solid is that a fluid offers almost no resistance to shearing stress: the smallest sideways push makes it flow. That is why we describe fluids at rest mainly by the pressure inside them.

Pressure and density

A sharp needle pierces skin while the back of a spoon pushed with the same force does not: the smaller the area, the greater the effect of a force. A fluid at rest pushes on any surface in contact with it, and this force is always normal (perpendicular) to the surface. If it had a component along the surface, then by Newton's third law the surface would push the fluid sideways and the fluid would flow, but a fluid at rest does not flow.

Average pressure P = F/A, where F is the normal force on area A. At a point, P = lim (ΔA → 0) ΔF/ΔA. SI unit: N m⁻² = pascal (Pa). Dimensions [ML⁻¹T⁻²]. Pressure is a scalar.

Density ρ = m/V, in kg m⁻³, dimensions [ML⁻³]. Water at 4 °C has a density of 1.0 × 10³ kg m⁻³. Relative density is the density of a substance divided by the density of water at 4 °C; it has no unit (aluminium has relative density 2.7, so its density is 2.7 × 10³ kg m⁻³). Liquids are nearly incompressible, so their density hardly changes with pressure; the density of a gas changes a lot.

Pascal's law

Imagine a tiny right-angled prism of fluid inside a fluid at rest, so small that gravity acts equally on all of it. The surrounding fluid pushes normally on each of its three rectangular faces. Balancing the forces and using the geometry of the faces (the force on the sloping face resolves into the forces on the other two, and the areas are related by the same sine and cosine), the three pressures come out equal. So the pressure at a point in a fluid at rest is the same in all directions; no direction can be given to it, which is why pressure is a scalar. Next imagine a horizontal bar of fluid in equilibrium: the forces at its two ends must balance, so the pressure is the same at all points on the same horizontal level. If it were not, the fluid would flow.

How pressure increases with depth

  1. Take a vertical cylinder of fluid of cross-section A and height h, with point 1 at its top and point 2 at its bottom.
  2. Horizontal forces cancel. Vertically: P₂A acts upward, P₁A acts downward, and the weight mg acts downward.
  3. For equilibrium: (P₂ − P₁)A = mg.
  4. The mass is m = ρV = ρAh, so (P₂ − P₁)A = ρAhg, giving P₂ − P₁ = ρgh.
  5. If point 1 is at the open surface, P₁ = Pa (atmospheric pressure), so the pressure at depth h is P = Pa + ρgh.

P = Pa + ρgh. The excess P − Pa = ρgh is the gauge pressure. The area and shape of the container do not appear.

This leads to the hydrostatic paradox. Vessels of very different shapes, joined at the bottom by a horizontal pipe and filled with water, all fill to the same level although they hold different amounts of water. The pressure at the bottom depends only on the depth of liquid above it, not on how much liquid there is.

From forces on a column to P = Pa + ρgh

  1. Fluid column at rest Area A, height h, density ρ.
  2. Balance vertical forces (P₂ − P₁)A = mg.
  3. Substitute m = ρAh P₂ − P₁ = ρgh.
  4. Top open to air P = Pa + ρgh at depth h.

Worked example 1: a diver at 20 m

Find the absolute pressure on a diver 20 m below the surface of a freshwater lake. Take Pa = 1.01 × 10⁵ Pa, ρ = 1000 kg m⁻³ and g = 9.8 m s⁻². ρgh = 1000 × 9.8 × 20 = 1.96 × 10⁵ Pa. P = 1.01 × 10⁵ + 1.96 × 10⁵ = 2.97 × 10⁵ Pa, roughly three atmospheres. Every 10 m of water adds nearly one atmosphere.

Worked example 2: same force, different areas

A 3.0 kg brick measures 20 cm × 10 cm × 5 cm. Find the pressure it exerts on the floor when resting on its largest and smallest faces (g = 9.8 m s⁻²). Weight F = 3.0 × 9.8 = 29.4 N. Largest face: A = 0.20 × 0.10 = 0.020 m², P = 29.4/0.020 = 1470 Pa. Smallest face: A = 0.10 × 0.05 = 0.0050 m², P = 29.4/0.0050 = 5880 Pa. The force is the same; the pressure is four times larger because the area is four times smaller.

Worked example 3: pressure difference in oil

Two points in a tank of oil (ρ = 800 kg m⁻³) are 0.50 m apart vertically. Their pressure difference is ρgh = 800 × 9.8 × 0.50 = 3920 Pa, whatever the width of the tank and whatever the air pressure above it.

Key takeaways

  • A fluid at rest exerts force normal to every surface; pressure P = F/A is a scalar.
  • Pascal's law: pressure at a point acts equally in all directions and is equal at all points on one horizontal level.
  • P = Pa + ρgh; the shape of the vessel does not matter (hydrostatic paradox).
  • Gauge pressure = P − Pa = ρgh.

Check your understanding

  1. 1. Why must the force exerted by a fluid at rest on a submerged surface be perpendicular to that surface?

    1. Because pressure is a vector pointing downward
    2. Because a force component along the surface would make the fluid flow, and a fluid at rest does not flow
    3. Because gravity acts only perpendicular to surfaces
    4. Because fluids cannot exert any force on solids
    Show answer

    Answer: B. If the fluid pushed with a component parallel to the surface, the surface would push back on the fluid (Newton's third law) and the fluid, which cannot resist shear, would flow along it. Since it is at rest, the force can only be normal.

  2. 2. What is the gauge pressure 10 m below the surface of fresh water? Take ρ = 1000 kg m⁻³ and g = 9.8 m s⁻².

    1. 9.8 × 10³ Pa
    2. 1.01 × 10⁵ Pa
    3. 9.8 × 10⁴ Pa
    4. 1.99 × 10⁵ Pa
    Show answer

    Answer: C. Gauge pressure = ρgh = 1000 × 9.8 × 10 = 9.8 × 10⁴ Pa. Adding atmospheric pressure would give the absolute pressure, about 1.99 × 10⁵ Pa, which is not what was asked.

  3. 3. Three vessels of different shapes, connected at the bottom, are filled with water to the same height. What can be said about the pressure at their bases?

    1. It is greatest in the vessel holding the most water
    2. It is greatest in the narrowest vessel
    3. It is the same in all three
    4. It depends on the area of each base
    Show answer

    Answer: C. Pressure at depth h is Pa + ρgh. The depth, the liquid and the atmosphere are the same for all three, so the pressure at the base is the same. The amount of water and the shape do not enter: this is the hydrostatic paradox.

  4. 4. What is the gauge pressure at a point 2.0 m below the surface of an oil of density 800 kg m⁻³? (g = 9.8 m s⁻²)

    1. 1.6 × 10⁴ Pa
    2. 1.6 × 10³ Pa
    3. 4.0 × 10³ Pa
    4. 7.8 × 10³ Pa
    Show answer

    Answer: A. ρgh = 800 × 9.8 × 2.0 = 15 680 Pa ≈ 1.6 × 10⁴ Pa.

  5. 5. Assertion (A): Pressure is a scalar quantity. Reason (R): At a point in a fluid at rest, pressure acts equally in all directions, so no particular direction can be assigned to it.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. The force on a surface is a vector, but pressure is the normal force per unit area and is the same whatever way the surface faces. Because it has no direction of its own, pressure is a scalar; R explains A.

Privacy · Terms · Refunds · Delivery