- Foundation
- About 22 min
- 5 practice questions
Surface tension, drops, bubbles and capillary rise
Explain surface energy and surface tension, use S = F/2l, relate the angle of contact to wetting, find excess pressure in drops and bubbles, and derive the capillary rise h = 2S cos θ/(ρga).
If something looks wrong, please tell us.
By the end of this lesson you can
- Explain why molecules at a liquid surface have extra energy.
- Define surface tension as force per unit length and as surface energy per unit area.
- Relate the angle of contact to wetting and to wetting and waterproofing agents.
- Derive the excess pressure in a drop (2S/r) and a bubble (4S/r) and the capillary rise h = 2S cos θ/(ρga).
Oil and water do not mix, water wets glass but rolls off a lotus leaf, mercury forms beads, and oil climbs a lamp wick against gravity. A paint brush's hairs spread apart in water but cling to a fine tip when lifted out. All these come from the special energy of a liquid's free surface, an effect called surface tension. Gases have no free surface, so this is a property of liquids at an interface.
Surface energy
Molecules in a liquid attract each other, which gives each one a negative potential energy. A molecule deep inside is surrounded on all sides; a molecule at the surface has neighbours only on one side, so its potential energy is less negative, roughly half as much. Molecules at the surface therefore have extra energy compared with those inside. To increase the surface area, molecules must be brought from inside to the surface, which takes energy. So a liquid tends to take the least surface area its conditions allow.
Surface tension: S = F/2l
Form a soap film on a U-shaped wire frame closed by a light slider of length l. The film pulls the slider inward. To pull the slider out a distance d at steady speed takes a force F and work Fd. A film has two surfaces, so the new area is 2dl, and if S is the surface energy per unit area, S(2dl) = Fd, giving S = F/(2l). So surface tension S is both the surface energy per unit area and the force per unit length acting in the plane of the surface. Unit: N m⁻¹ = J m⁻². Standard values at 20 °C are about 0.073 N m⁻¹ for water and 0.44 N m⁻¹ for mercury. Surface tension usually falls as temperature rises, and strictly it belongs to the interface between two materials, not to one liquid alone.
Surface tension S = F/(2l) for a film (two surfaces) = surface energy per unit area. Unit N m⁻¹ or J m⁻².
Worked example 1: a soap film
A soap film on a frame holds a slider 10 cm long in equilibrium against a total downward pull of 5.0 × 10⁻³ N. S = F/(2l) = 5.0 × 10⁻³/(2 × 0.10) = 0.025 N m⁻¹. The 2 is there because the film has a front and a back surface.
Angle of contact and wetting
Where a liquid meets a solid its surface is curved. The angle of contact θ is the angle between the tangent to the liquid surface at the point of contact and the solid surface, measured inside the liquid. Balancing the three interfacial tensions (liquid-air Sla, solid-liquid Ssl, solid-air Ssa) along the solid gives Sla cos θ + Ssl = Ssa. If the liquid's molecules attract the solid strongly, Ssl is small, θ is acute and the liquid spreads and wets the solid (water on clean glass or plastic, kerosene on almost anything). If they attract each other more strongly than the solid, Ssl is large, θ is obtuse and the liquid forms drops (water on a lotus leaf or waxy surface, mercury on glass). Soaps and detergents are wetting agents: they reduce θ so the water gets into fabric. Waterproofing agents do the reverse and make θ large.
Wetting and non-wetting liquids
-
Acute angle of contact
- Liquid attracted strongly to the solid
- Spreads and wets the surface
- Concave meniscus; rises in a capillary
- Water on clean glass
-
Obtuse angle of contact
- Liquid attracted more to itself
- Forms drops, does not wet
- Convex meniscus; falls in a capillary
- Mercury on glass, water on a lotus leaf
Drops and bubbles
With gravity negligible, free drops and bubbles are spherical, because for a given volume a sphere has the least surface area and so the least surface energy. The pressure inside a drop is greater than outside. Let a drop of radius r grow by Δr. Extra surface energy = S × [4π(r + Δr)² − 4πr²] ≈ 8πrΔr S. Work done by the excess pressure in expanding it = (Pi − Po) × 4πr²Δr. In equilibrium these are equal, giving Pi − Po = 2S/r for a drop (or an air cavity inside a liquid, which also has one surface). A soap bubble has two surfaces (inside and outside of the film), so Pi − Po = 4S/r. In general the concave side of a curved surface is at the higher pressure.
Worked example 2: excess pressures
(a) A water drop of radius 1.0 mm, S = 0.073 N m⁻¹: Pi − Po = 2S/r = 2 × 0.073/1.0 × 10⁻³ = 146 Pa. (b) A soap bubble of radius 2.0 cm, S = 0.025 N m⁻¹: Pi − Po = 4S/r = 4 × 0.025/0.020 = 5.0 Pa. (c) The work needed to blow a soap bubble of radius 1.0 cm from a tiny size, with S = 0.025 N m⁻¹, equals S × (new surface area). The film has two surfaces, so the area is 2 × 4πr²: W = 0.025 × 2 × 4π × (0.010)² = 6.3 × 10⁻⁵ J.
Capillary rise
Dip a narrow glass tube (radius a) in water. Water wets glass, so the meniscus is concave, and the pressure just under it is lower than atmospheric. Water is pushed up the tube until the hydrostatic pressure of the column makes up the difference.
- The meniscus is part of a sphere of radius r = a/cos θ (θ = angle of contact).
- Pressure difference across it: Po − Pi = 2S/r = (2S cos θ)/a, the liquid side being lower.
- Points at the level of the outside water surface, inside and outside the tube, are at the same pressure: Pi + hρg = Po.
- So hρg = (2S cos θ)/a, giving h = 2S cos θ/(ρga).
Capillary rise h = 2S cos θ/(ρga). The narrower the tube, the higher the rise; if θ is obtuse (mercury), cos θ < 0 and the liquid is depressed.
Worked example 3: water in a fine tube
Find the rise of water (S = 0.073 N m⁻¹, θ ≈ 0, ρ = 1000 kg m⁻³) in a glass tube of radius 0.25 mm, with g = 9.8 m s⁻². h = 2S/(ρga) = (2 × 0.073)/(1000 × 9.8 × 2.5 × 10⁻⁴) = 0.146/2.45 = 0.060 m = 6.0 cm. Halving the radius would double the rise.
Key takeaways
- Surface molecules have extra energy; liquids minimise surface area, so free drops are spherical.
- S = force per unit length = energy per unit area; a film has two surfaces (S = F/2l).
- Acute θ: wets and rises; obtuse θ: forms beads and is depressed.
- Excess pressure: drop or cavity 2S/r, soap bubble 4S/r; capillary rise h = 2S cos θ/(ρga).
Check your understanding
-
1. Which of these is a correct SI unit of surface tension?
- J m⁻²
- N m⁻²
- N m
- J m⁻¹
Show answer
Answer: A. Surface tension is force per unit length (N m⁻¹) and also energy per unit area (J m⁻²). These are the same, since J m⁻² = N m/m² = N m⁻¹. N m⁻² is the unit of pressure.
-
2. What is the excess pressure inside a soap bubble of radius 1.0 cm if the surface tension of the soap solution is 0.030 N m⁻¹?
- 6.0 Pa
- 3.0 Pa
- 12 Pa
- 0.12 Pa
Show answer
Answer: C. A soap bubble has two surfaces, so Pi − Po = 4S/r = 4 × 0.030/0.010 = 12 Pa. Using 2S/r, the formula for a drop, would give only 6.0 Pa.
-
3. A glass capillary tube is dipped into mercury. What happens to the mercury inside the tube?
- It rises above the outside level, with a concave meniscus
- It stays exactly level with the outside
- It is depressed below the outside level, with a convex meniscus
- It rises because mercury is very dense
Show answer
Answer: C. Mercury does not wet glass, so its angle of contact is obtuse and cos θ is negative. Then h = 2S cos θ/(ρga) is negative: the mercury is pushed below the outside level and its surface is convex.
-
4. Water rises 3.0 cm in a capillary tube. In a tube of the same glass with half the radius, the rise would be
- 1.5 cm
- 6.0 cm
- 12 cm
- 3.0 cm
Show answer
Answer: B. h = 2S cos θ/(ρga), so h ∝ 1/a. Halving the radius doubles the rise: 2 × 3.0 = 6.0 cm.
-
5. Why are detergents added to water for washing clothes?
- They increase the surface tension and the angle of contact
- They raise the density of water
- They make water more viscous
- They reduce the angle of contact so that water wets and penetrates the fibres
Show answer
Answer: D. Detergents are wetting agents. They lower the angle of contact between water and the fibres, so water spreads into the narrow spaces of the fabric and carries the dirt away. Waterproofing agents do the opposite.
Sign in to keep track of the lessons you finish.