• Foundation
  • About 22 min
  • 5 practice questions

Cells: emf, internal resistance and combinations

Define the emf of a cell, use V = ε − Ir and I = ε/(R + r), and find the equivalent emf and internal resistance of cells joined in series and in parallel.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Explain what emf means and why it is not a force.
  • Use V = ε − Ir for a discharging cell and V = ε + Ir for a cell being charged.
  • Find the current I = ε/(R + r) and the maximum current ε/r.
  • Derive and use the equivalent emf and internal resistance for cells in series and in parallel.

A torch battery labelled 1.5 V does not always deliver 1.5 V to the bulb - the voltage at its terminals drops as it supplies more current. This lesson explains why, using two quantities that describe any cell: its emf and its internal resistance.

Emf of a cell

A cell has a positive electrode P and a negative electrode N dipped in an electrolyte. At each electrode, charge exchange with the electrolyte creates a potential jump: P is at +V₊ relative to the electrolyte next to it, and N is at −V₋ relative to the electrolyte next to it. With no current, the electrolyte is at one potential throughout, so the potential difference between P and N is V₊ + V₋. This is the electromotive force (emf) ε of the cell.

ε = potential difference between the terminals of a cell when no current is drawn (open circuit). It is the work done by the cell per unit charge in moving charge from its lower to its higher potential terminal.

Despite the name, emf is a potential difference measured in volts, not a force; the name is historical.

Internal resistance and terminal voltage

When a resistor R is connected, a current I flows through R from P to N, and through the electrolyte from N to P. The electrolyte has a resistance r, the internal resistance, so some of the emf is used up inside the cell:

V = ε − Ir (terminal voltage while the cell supplies current I). With V = IR: I = ε/(R + r). Maximum current (R = 0): I_max = ε/r.

  • Open circuit (I = 0): V = ε.
  • When Ir ≪ ε, the internal resistance can be ignored.
  • Dry cells have much higher internal resistance than common electrolytic cells.
  • Real cells are usually limited to currents far below ε/r to avoid damage.
  • When a cell is being charged, current is forced into it at the positive terminal, and V = ε + Ir: the terminal voltage exceeds the emf.

Worked example 1: terminal voltage

A battery of emf 9 V and internal resistance 0.5 Ω is connected to a 4 Ω resistor. I = ε/(R + r) = 9 ÷ 4.5 = 2 A. Terminal voltage V = ε − Ir = 9 − 2 × 0.5 = 8 V (check: IR = 2 × 4 = 8 V). The largest current it could ever drive, with its terminals shorted, is 9 ÷ 0.5 = 18 A.

Cells in series

Join the negative terminal of cell 1 (ε₁, r₁) to the positive of cell 2 (ε₂, r₂), with the same current I through both. Across each, V = ε − Ir, so across the pair V = (ε₁ + ε₂) − I(r₁ + r₂). Comparing with V = ε_eq − I r_eq:

Series: ε_eq = ε₁ + ε₂ + ... and r_eq = r₁ + r₂ + ... . A cell connected the opposite way round (current leaving it from its negative terminal) enters with a minus sign: ε_eq = ε₁ − ε₂.

Cells in parallel

Join positive to positive and negative to negative. With I₁ and I₂ leaving the cells, I = I₁ + I₂, and both cells share the same terminal voltage V: I₁ = (ε₁ − V)/r₁ and I₂ = (ε₂ − V)/r₂. Adding and rearranging into V = ε_eq − I r_eq gives:

Parallel: 1/r_eq = 1/r₁ + 1/r₂ + ... and ε_eq/r_eq = ε₁/r₁ + ε₂/r₂ + ... . For two cells: ε_eq = (ε₁r₂ + ε₂r₁)/(r₁ + r₂), r_eq = r₁r₂/(r₁ + r₂).

Cells in series and in parallel

  • Series
    • Same current through each cell
    • Emfs add (with signs)
    • Internal resistances add
    • Gives a larger emf
  • Parallel
    • Same terminal voltage
    • Currents from the cells add
    • 1/r_eq = Σ 1/r
    • For identical cells: same emf, smaller r, can supply more current

Worked example 2: series and parallel cells

(a) Three cells, each 1.5 V and 0.2 Ω, in series drive a 3.9 Ω resistor. ε_eq = 4.5 V, r_eq = 0.6 Ω, I = 4.5 ÷ (3.9 + 0.6) = 1 A. (b) Cells of 6 V, 2 Ω and 3 V, 1 Ω are joined in parallel. r_eq = (2 × 1)/(2 + 1) ≈ 0.67 Ω and ε_eq = (6 × 1 + 3 × 2)/(2 + 1) = 12 ÷ 3 = 4 V. Check: ε_eq/r_eq = 4 ÷ 0.667 = 6, and ε₁/r₁ + ε₂/r₂ = 3 + 3 = 6.

Worked example 3: charging a battery

A battery of emf 6 V and internal resistance 0.5 Ω is charged from a 24 V dc supply through a series resistor of 8.5 Ω. The supply drives current into the battery's positive terminal against its emf: I = (24 − 6) ÷ (8.5 + 0.5) = 18 ÷ 9 = 2 A. Terminal voltage during charging V = ε + Ir = 6 + 2 × 0.5 = 7 V. Without the series resistor the current would be 36 A, enough to damage the battery; the resistor limits it.

Key takeaways

  • Emf = terminal p.d. on open circuit; it is a potential difference, not a force.
  • V = ε − Ir when supplying current, V = ε + Ir when being charged; I = ε/(R + r).
  • Series: emfs and internal resistances add. Parallel: 1/r_eq = Σ1/rᵢ and ε_eq/r_eq = Σ εᵢ/rᵢ.

Check your understanding

  1. 1. A cell of emf 2.0 V and internal resistance 0.5 Ω drives a current through a 3.5 Ω resistor. What is the terminal voltage?

    1. 2.0 V
    2. 1.75 V
    3. 0.25 V
    4. 1.5 V
    Show answer

    Answer: B. I = ε/(R + r) = 2.0 ÷ 4.0 = 0.5 A. V = ε − Ir = 2.0 − 0.5 × 0.5 = 1.75 V (also IR = 0.5 × 3.5 = 1.75 V).

  2. 2. The terminal voltage of a battery is 10 V on open circuit and falls to 9 V when it supplies 2 A. What is its internal resistance?

    1. 0.5 Ω
    2. 4.5 Ω
    3. 2 Ω
    4. 5 Ω
    Show answer

    Answer: A. Open-circuit voltage = emf = 10 V. V = ε − Ir gives 9 = 10 − 2r, so r = 0.5 Ω.

  3. 3. Four identical cells, each of emf 1.5 V and internal resistance 0.4 Ω, are joined in series. What are the emf and internal resistance of the combination?

    1. 1.5 V, 0.1 Ω
    2. 6 V, 0.1 Ω
    3. 1.5 V, 1.6 Ω
    4. 6 V, 1.6 Ω
    Show answer

    Answer: D. In series, emfs add (4 × 1.5 = 6 V) and internal resistances add (4 × 0.4 = 1.6 Ω).

  4. 4. Two identical cells of emf ε and internal resistance r are joined in parallel. The combination has

    1. emf 2ε and internal resistance 2r
    2. emf ε/2 and internal resistance r/2
    3. emf ε and internal resistance r/2
    4. emf ε and internal resistance 2r
    Show answer

    Answer: C. 1/r_eq = 1/r + 1/r gives r_eq = r/2, and ε_eq = r_eq (ε/r + ε/r) = (r/2)(2ε/r) = ε.

  5. 5. Assertion (A): While a battery is being charged, its terminal voltage is greater than its emf. Reason (R): During charging, current flows through the battery from its positive to its negative terminal, so V = ε + Ir.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. Both are true. The charger pushes current into the positive terminal against the emf, and the drop across the internal resistance adds to the emf, giving V = ε + Ir > ε. R explains A.

Privacy · Terms · Refunds · Delivery