• Foundation
  • About 25 min
  • 5 practice questions

Kirchhoff's rules and the Wheatstone bridge

State and justify Kirchhoff's junction and loop rules, apply them with a consistent sign convention to solve multi-loop circuits, and derive the balance condition of the Wheatstone bridge.

If something looks wrong, please tell us.

By the end of this lesson you can

  • State Kirchhoff's junction rule and loop rule and the conservation laws behind them.
  • Use a sign convention to write loop equations for resistors and cells.
  • Solve a two-loop circuit and interpret a negative answer for a current.
  • Derive the Wheatstone bridge balance condition and use it to find an unknown resistance.

Series and parallel formulas cannot handle every circuit - for example, two batteries in different branches feeding one resistor. Kirchhoff's two rules can solve any network of resistors and cells, and they lead directly to the Wheatstone bridge, a precise way to measure resistance.

Setting up a circuit

Label each branch with a current and an arrow. If a current comes out positive, it flows the way the arrow points; if negative, it flows the opposite way - so the guess of direction does not matter. For a cell with emf ε and internal resistance r, going from its negative to its positive terminal through the cell in the direction of current I, the potential rises by ε − Ir.

The two rules

Junction rule: at any junction, the sum of currents entering equals the sum of currents leaving. (Conservation of charge: for steady currents no charge piles up anywhere.)

Loop rule: the algebraic sum of the changes in potential around any closed loop is zero. (Potential depends only on position, so returning to the start brings you back to the same potential.)

Sign convention for the loop rule
Element crossedDirection of travelChange in potential
Resistor RAlong the current I−IR (drop)
Resistor RAgainst the current I+IR (rise)
Cell (emf ε)From − terminal to + terminal+ε
Cell (emf ε)From + terminal to − terminal−ε

Solving a network with Kirchhoff's rules

  1. Label currents Use the junction rule at once to keep the number of unknowns small.
  2. Pick independent loops As many loops as there are unknown currents still left.
  3. Walk each loop Add potential changes with the sign convention and set the sum to zero.
  4. Solve Solve the simultaneous equations; a negative current flows opposite to its arrow.
  5. Check Test the answer on a loop you did not use.

Worked example 1: two cells, three branches

A 12 V cell in series with 2 Ω forms the left branch; a 6 V cell in series with 2 Ω forms the right branch; a 4 Ω resistor forms the middle branch. The positive terminals both face the top junction. Let I₁ flow up the left branch, I₂ up the right branch and I₃ down the middle (cell internal resistances are included in the 2 Ω).

  1. Junction rule at the top: I₃ = I₁ + I₂.
  2. Left loop (up the left branch, down the middle): 12 − 2I₁ − 4I₃ = 0.
  3. Right loop (up the right branch, down the middle): 6 − 2I₂ − 4I₃ = 0.
  4. Subtracting: 6 − 2I₁ + 2I₂ = 0, so I₁ = I₂ + 3. Then I₃ = 2I₂ + 3.
  5. Right loop: 6 − 2I₂ − 4(2I₂ + 3) = 0 gives −10I₂ = 6, so I₂ = −0.6 A.
  6. So I₁ = 2.4 A and I₃ = 1.8 A. Check in the left loop: 12 − 4.8 − 7.2 = 0.

The negative I₂ means 0.6 A actually flows down through the 6 V cell: the 12 V cell is charging it. Kirchhoff's rules revealed this without any guesswork.

Symmetry helps

In symmetric networks, equal currents can be spotted before writing equations. For instance, in a cube of twelve equal resistors R with a battery across opposite corners, the three edges leaving the first corner carry equal currents, each splitting equally at the next corners. One loop equation then gives the equivalent resistance as 5R/6. In a general network there is no such shortcut, and the full set of equations is needed.

The Wheatstone bridge

Four resistors R₁, R₂, R₃, R₄ form a loop ABCD. A cell is connected across A and C (the battery arm), and a galvanometer G across B and D (the galvanometer arm). In general current flows through G. The bridge is balanced when the galvanometer current I_g = 0.

  1. With I_g = 0, the junction rule at B and D gives: the current I₁ through R₁ continues through R₃, and the current I₂ through R₂ continues through R₄.
  2. Loop through R₁, G and R₂: −I₁R₁ + 0 + I₂R₂ = 0, so I₁/I₂ = R₂/R₁.
  3. Loop through R₄, G and R₃: I₂R₄ + 0 − I₁R₃ = 0, so I₁/I₂ = R₄/R₃.
  4. Equating: R₂/R₁ = R₄/R₃.

Balance condition: R₂/R₁ = R₄/R₃, so an unknown R₄ = R₃ (R₂/R₁). At balance there is no current through the galvanometer (null deflection).

To measure an unknown resistance, put it in the fourth arm, fix R₁ and R₂, and adjust R₃ until the galvanometer shows no deflection. The meter bridge is a practical device that works on this principle. Because the method looks for zero current, the galvanometer's own resistance does not affect the result.

Worked example 2: finding an unknown resistance

A bridge balances with R₁ = 40 Ω, R₂ = 10 Ω and R₃ = 60 Ω. R₄ = R₃ × R₂/R₁ = 60 × 10 ÷ 40 = 15 Ω. Check: R₂/R₁ = 0.25 and R₄/R₃ = 15/60 = 0.25.

Worked example 3: is the bridge balanced?

A bridge has R₁ = 5 Ω, R₂ = 10 Ω, R₃ = 15 Ω, R₄ = 30 Ω. R₂/R₁ = 2 and R₄/R₃ = 2, so it is balanced and no current flows through the galvanometer, whatever the battery voltage. If R₄ is changed to 33 Ω, R₄/R₃ = 2.2 ≠ 2: a current flows through G, and finding its size needs the full Kirchhoff equations for three loops.

Key takeaways

  • Junction rule: currents in = currents out (charge conservation).
  • Loop rule: sum of potential changes round a loop = 0 (energy/position-dependence of potential).
  • A negative answer for a current means it flows opposite to the arrow you drew.
  • Wheatstone bridge balance: R₂/R₁ = R₄/R₃, with zero galvanometer current.

Check your understanding

  1. 1. Kirchhoff's junction rule is a consequence of the conservation of

    1. energy
    2. charge
    3. momentum
    4. mass of the wires
    Show answer

    Answer: B. For steady currents charge cannot pile up at a junction, so the total current entering must equal the total leaving. This is conservation of charge.

  2. 2. Currents of 3 A and 2 A flow into a junction, and a current of 4 A flows out along one wire. What current flows in the only other wire, and which way?

    1. 1 A out of the junction
    2. 1 A into the junction
    3. 9 A out of the junction
    4. 5 A into the junction
    Show answer

    Answer: A. Total in = 3 + 2 = 5 A. Out so far = 4 A. By the junction rule the remaining wire must carry 5 − 4 = 1 A out of the junction.

  3. 3. Going round a loop in the direction of the current, you cross a 5 Ω resistor carrying 2 A and then a cell of emf 12 V from its negative to its positive terminal. The total change in potential over these two elements is

    1. −22 V
    2. +22 V
    3. −2 V
    4. +2 V
    Show answer

    Answer: D. Across the resistor along the current: −IR = −2 × 5 = −10 V. Across the cell from − to +: +12 V. Total = −10 + 12 = +2 V.

  4. 4. A Wheatstone bridge is balanced with R₁ = 100 Ω, R₂ = 20 Ω and R₃ = 250 Ω. What is the fourth resistance R₄?

    1. 1250 Ω
    2. 8 Ω
    3. 50 Ω
    4. 500 Ω
    Show answer

    Answer: C. R₂/R₁ = R₄/R₃, so R₄ = R₃ × R₂/R₁ = 250 × 20 ÷ 100 = 50 Ω.

  5. 5. Assertion (A): The balance condition of a Wheatstone bridge does not depend on the resistance of the galvanometer. Reason (R): At balance no current flows through the galvanometer, so there is no potential drop across it.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. Both are true. At balance I_g = 0, so the galvanometer arm contributes 0 × R_G = 0 to each loop equation, and its resistance drops out of R₂/R₁ = R₄/R₃. R explains A, and this is why a null method is so accurate.

Privacy · Terms · Refunds · Delivery