• Foundation
  • About 22 min
  • 5 practice questions

Limits of Ohm's law, resistivity, temperature and electrical power

Identify non-ohmic behaviour, compare resistivities of conductors, semiconductors and insulators, use ρ_T = ρ₀[1 + α(T − T₀)], and calculate power P = VI = I²R = V²/R, including transmission losses.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe three ways in which devices can fail to obey Ohm's law.
  • Classify materials by resistivity and explain alloys used in standard resistors.
  • Use the temperature coefficient of resistivity, and explain the opposite behaviour of metals and semiconductors.
  • Derive P = VI and use P = I²R = V²/R, including why power is transmitted at high voltage.

Ohm's law is very useful, but it is not a law of nature like conservation of charge - it is a property that many materials have over a limited range. This lesson looks at where it fails, how resistivity changes with material and temperature, and what happens to the energy that a current delivers.

Limitations of Ohm's law

Many materials and devices used in circuits are non-ohmic: their current is not simply proportional to the voltage. The deviations are of three kinds:

  1. V stops being proportional to I - for example, the I-V graph of a good conductor bends away from a straight line at large currents.
  2. The relation depends on the sign of V: reversing the voltage does not give the same current in the opposite direction. A diode (studied in a later chapter) behaves like this.
  3. The relation is not unique: the same current can occur at more than one voltage. Gallium arsenide (GaAs) shows such behaviour.

Note that V = IR defines resistance for any device; a device obeys Ohm's law only if R does not depend on V or on its sign, so that the I-V graph is a straight line through the origin.

Resistivity of materials

Materials classified by resistivity
ClassTypical resistivityBehaviour
Metals (conductors)10⁻⁸ to 10⁻⁶ Ω mResistivity rises with temperature
Semiconductors (Si, Ge)In between, on a logarithmic scaleResistivity falls with temperature; can be lowered greatly by adding small amounts of impurity
Insulators (glass, rubber, ceramics, plastics)About 10¹⁸ or more times that of metalsVery few free carriers

Temperature dependence of resistivity

Over a limited range of temperature, the resistivity of a metal increases roughly linearly:

ρ_T = ρ₀ [1 + α (T − T₀)], where α is the temperature coefficient of resistivity (unit °C⁻¹ or K⁻¹). For metals α > 0. The same form applies to the resistance R of a given wire.

Far below 0 °C the graph of a metal's resistivity bends away from a straight line, so the formula is used only near a reference temperature. Alloys such as nichrome, manganin and constantan have very small α; their resistance hardly changes with temperature, which is why they are used for standard resistors and heating elements.

Why the opposite trends? From ρ = m/(ne²τ): in a metal, n hardly changes with temperature, but hotter electrons and more vigorously vibrating ions mean more frequent collisions, so τ falls and ρ rises. In semiconductors and insulators, n increases strongly with temperature, which more than outweighs the fall in τ, so ρ falls.

Effect of heating on resistivity

  • Metal
    • n almost constant
    • τ decreases (more collisions)
    • ρ increases
    • α positive
  • Semiconductor
    • n increases sharply
    • τ decreases a little
    • ρ decreases
    • α negative

Worked example 1: resistance at a higher temperature

A metal coil has resistance 50 Ω at 20 °C and α = 4.0 × 10⁻³ °C⁻¹ (an illustrative value). At 70 °C: R = 50 [1 + 4.0 × 10⁻³ × (70 − 20)] = 50 × (1 + 0.2) = 60 Ω.

Worked example 2: temperature of a heater element

A heater element measures 80 Ω at a room temperature of 27 °C with a tiny current. In steady use on its supply it draws a current that shows its resistance to be 92 Ω. Taking α = 1.5 × 10⁻⁴ °C⁻¹ over this range, T − 27 = (92 − 80) ÷ (80 × 1.5 × 10⁻⁴) = 12 ÷ 0.012 = 1000 °C, so the element runs at about 1027 °C. When first switched on, the cold element draws slightly more current; it settles as the element heats up and its resistance rises.

Electrical energy and power

Let current I flow from A to B through a conductor, with V(A) − V(B) = V > 0. In time Δt, charge ΔQ = IΔt moves from A to B, so its potential energy changes by ΔQ[V(B) − V(A)] = −IVΔt. If the charges moved freely this energy would become kinetic energy. But they drift at a steady speed, because collisions hand the energy to the ions, which vibrate more: the conductor heats up. Energy dissipated in time Δt is ΔW = IVΔt, so the power is:

P = VI = I²R = V²/R (watts). The energy comes from the source, for example the chemical energy of a cell.

Power transmission. To deliver power P to a distant town at voltage V, the current in the cables is I = P/V, and the power wasted in cables of resistance R_c is P_c = I²R_c = P²R_c/V². The loss falls as 1/V², so power is transmitted at very high voltages - hence the danger signs on transmission towers - and transformers lower the voltage to safe values near the consumer.

Worked example 3: heater and transmission

(a) A 1000 W heater runs on 250 V. I = P/V = 4 A; R = V²/P = 62 500 ÷ 1000 = 62.5 Ω. In 2 hours it uses 1000 × 7200 = 7.2 × 10⁶ J (2 kWh). (b) 100 kW is sent through lines of total resistance 0.5 Ω. At 10 kV, I = 10 A and loss = 10² × 0.5 = 50 W. At 1 kV, I = 100 A and loss = 100² × 0.5 = 5000 W - a hundred times more.

Key takeaways

  • Ohm's law fails for non-linear, direction-dependent or non-unique I-V relations (e.g. diodes, GaAs).
  • ρ_T = ρ₀[1 + α(T − T₀)]; metals α > 0, semiconductors ρ falls with T; alloys have small α.
  • P = VI = I²R = V²/R; transmission loss ∝ 1/V², so power lines use high voltage.

Check your understanding

  1. 1. Which of these is a property of a non-ohmic device?

    1. Its I-V graph is a straight line through the origin
    2. Its resistance does not depend on the applied voltage
    3. Reversing the voltage reverses the current with the same magnitude
    4. Reversing the voltage gives a current of a different magnitude
    Show answer

    Answer: D. A device that responds differently to the two polarities (such as a diode) does not obey Ohm's law. The other three describe ohmic behaviour.

  2. 2. A wire has resistance 2.0 Ω at 25 °C and 2.5 Ω at 125 °C. What is its temperature coefficient of resistance (taking 25 °C as reference)?

    1. 2.5 × 10⁻³ °C⁻¹
    2. 5.0 × 10⁻³ °C⁻¹
    3. 2.0 × 10⁻³ °C⁻¹
    4. 4.0 × 10⁻³ °C⁻¹
    Show answer

    Answer: A. α = (R₂ − R₁)/(R₁ × ΔT) = (2.5 − 2.0) ÷ (2.0 × 100) = 0.5 ÷ 200 = 2.5 × 10⁻³ °C⁻¹.

  3. 3. Why does the resistivity of a semiconductor decrease as it is heated?

    1. The relaxation time increases sharply
    2. The number of free charge carriers per unit volume increases a lot
    3. The ions stop vibrating
    4. Its length decreases
    Show answer

    Answer: B. ρ = m/(ne²τ). In a semiconductor, heating frees many more carriers, so n rises much more than τ falls, and ρ decreases.

  4. 4. A 60 W lamp is rated for 240 V. What is its resistance when working normally?

    1. 4 Ω
    2. 240 Ω
    3. 960 Ω
    4. 14 400 Ω
    Show answer

    Answer: C. R = V²/P = 240² ÷ 60 = 57 600 ÷ 60 = 960 Ω.

  5. 5. Assertion (A): Electric power is transmitted over long distances at very high voltage. Reason (R): For a given power, a higher voltage means a smaller current, and the loss in the cables is I²R.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. Both are true. I = P/V, so the cable loss I²R_c = P²R_c/V² falls as the square of the voltage rises. R explains A.

Privacy · Terms · Refunds · Delivery