Revision notes

Chapter 3 Current Electricity: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Electric current, Ohm's law and resistivity

I = lim (Δt → 0) ΔQ/Δt. SI unit: ampere (A), a base unit defined through the magnetic effect of currents; 1 A = 1 C s⁻¹.

V = RI, where R is the resistance of the conductor. SI unit: ohm (Ω), 1 Ω = 1 V A⁻¹.

R = ρ l/A, where ρ (resistivity) depends on the material and temperature but not on its size. Unit of ρ: Ω m.

j = σE, where σ = 1/ρ is the conductivity (unit S m⁻¹, siemens per metre). This is Ohm's law written for a point inside the material.

From a potential difference to a current

  1. Source keeps a potential difference V A cell maintains V across the ends of the wire.
  2. Uniform field inside E = V/l along the wire.
  3. Current density j = σE = E/ρ at every point.
  4. Current I = jA, which gives V = I (ρl/A) = IR.
  • I = dQ/dt in amperes; a steady current needs a source that maintains the field.
  • Ohm's law V = RI; R = ρl/A, with ρ a property of the material.
  • Current density j = I/A; at a point, j = σE with σ = 1/ρ.
Read the full lesson

Lesson 2

Drift of electrons, relaxation time and mobility

vd = −(eτ/m) E: the drift velocity. It is constant in time and opposite to E for electrons.

Life of a free electron in a field

  1. Collision with an ion Leaves in a random direction; drift gained so far is lost.
  2. Accelerates The field adds velocity −eE/m per second, opposite to E.
  3. Next collision Comes on average a time τ later; again the direction is randomised.
  4. Net result A steady average drift vd = eEτ/m opposite to E.

Then back to step 1: Collision with an ion

I = neA|vd|, so j = ne|vd|.

σ = ne²τ/m, and ρ = 1/σ = m/(ne²τ).

μ = |vd|/E = eτ/m. SI unit: m² V⁻¹ s⁻¹ (1 m² V⁻¹ s⁻¹ = 10⁴ cm² V⁻¹ s⁻¹). Mobility is taken as positive.

  • Without a field the average velocity of free electrons is zero.
  • With a field, vd = eEτ/m opposite to E; τ is the average time between collisions.
  • I = neAvd; σ = ne²τ/m and ρ = m/(ne²τ) - this is the origin of Ohm's law.
  • Mobility μ = vd/E = eτ/m, in m² V⁻¹ s⁻¹.
Read the full lesson

Lesson 3

Limits of Ohm's law, resistivity, temperature and electrical power

Materials classified by resistivity
ClassTypical resistivityBehaviour
Metals (conductors)10⁻⁸ to 10⁻⁶ Ω mResistivity rises with temperature
Semiconductors (Si, Ge)In between, on a logarithmic scaleResistivity falls with temperature; can be lowered greatly by adding small amounts of impurity
Insulators (glass, rubber, ceramics, plastics)About 10¹⁸ or more times that of metalsVery few free carriers

ρ_T = ρ₀ [1 + α (T − T₀)], where α is the temperature coefficient of resistivity (unit °C⁻¹ or K⁻¹). For metals α > 0. The same form applies to the resistance R of a given wire.

Effect of heating on resistivity

  • Metal
    • n almost constant
    • τ decreases (more collisions)
    • ρ increases
    • α positive
  • Semiconductor
    • n increases sharply
    • τ decreases a little
    • ρ decreases
    • α negative

P = VI = I²R = V²/R (watts). The energy comes from the source, for example the chemical energy of a cell.

  • Ohm's law fails for non-linear, direction-dependent or non-unique I-V relations (e.g. diodes, GaAs).
  • ρ_T = ρ₀[1 + α(T − T₀)]; metals α > 0, semiconductors ρ falls with T; alloys have small α.
  • P = VI = I²R = V²/R; transmission loss ∝ 1/V², so power lines use high voltage.
Read the full lesson

Lesson 4

Cells: emf, internal resistance and combinations

ε = potential difference between the terminals of a cell when no current is drawn (open circuit). It is the work done by the cell per unit charge in moving charge from its lower to its higher potential terminal.

V = ε − Ir (terminal voltage while the cell supplies current I). With V = IR: I = ε/(R + r). Maximum current (R = 0): I_max = ε/r.

Series: ε_eq = ε₁ + ε₂ + ... and r_eq = r₁ + r₂ + ... . A cell connected the opposite way round (current leaving it from its negative terminal) enters with a minus sign: ε_eq = ε₁ − ε₂.

Parallel: 1/r_eq = 1/r₁ + 1/r₂ + ... and ε_eq/r_eq = ε₁/r₁ + ε₂/r₂ + ... . For two cells: ε_eq = (ε₁r₂ + ε₂r₁)/(r₁ + r₂), r_eq = r₁r₂/(r₁ + r₂).

Cells in series and in parallel

  • Series
    • Same current through each cell
    • Emfs add (with signs)
    • Internal resistances add
    • Gives a larger emf
  • Parallel
    • Same terminal voltage
    • Currents from the cells add
    • 1/r_eq = Σ 1/r
    • For identical cells: same emf, smaller r, can supply more current
  • Emf = terminal p.d. on open circuit; it is a potential difference, not a force.
  • V = ε − Ir when supplying current, V = ε + Ir when being charged; I = ε/(R + r).
  • Series: emfs and internal resistances add. Parallel: 1/r_eq = Σ1/rᵢ and ε_eq/r_eq = Σ εᵢ/rᵢ.
Read the full lesson

Lesson 5

Kirchhoff's rules and the Wheatstone bridge

Junction rule: at any junction, the sum of currents entering equals the sum of currents leaving. (Conservation of charge: for steady currents no charge piles up anywhere.)

Loop rule: the algebraic sum of the changes in potential around any closed loop is zero. (Potential depends only on position, so returning to the start brings you back to the same potential.)

Sign convention for the loop rule
Element crossedDirection of travelChange in potential
Resistor RAlong the current I−IR (drop)
Resistor RAgainst the current I+IR (rise)
Cell (emf ε)From − terminal to + terminal+ε
Cell (emf ε)From + terminal to − terminal−ε

Solving a network with Kirchhoff's rules

  1. Label currents Use the junction rule at once to keep the number of unknowns small.
  2. Pick independent loops As many loops as there are unknown currents still left.
  3. Walk each loop Add potential changes with the sign convention and set the sum to zero.
  4. Solve Solve the simultaneous equations; a negative current flows opposite to its arrow.
  5. Check Test the answer on a loop you did not use.

Balance condition: R₂/R₁ = R₄/R₃, so an unknown R₄ = R₃ (R₂/R₁). At balance there is no current through the galvanometer (null deflection).

  • Junction rule: currents in = currents out (charge conservation).
  • Loop rule: sum of potential changes round a loop = 0 (energy/position-dependence of potential).
  • A negative answer for a current means it flows opposite to the arrow you drew.
  • Wheatstone bridge balance: R₂/R₁ = R₄/R₃, with zero galvanometer current.
Read the full lesson

Privacy · Terms · Refunds · Delivery