• Foundation
  • About 20 min
  • 5 practice questions

Faraday's experiments, magnetic flux and Faraday's law

Describe the experiments of Faraday and Henry, define magnetic flux Φ = BA cos θ, and use Faraday's law ε = −N dΦ/dt to calculate induced emfs and currents.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Describe the three key experiments that revealed electromagnetic induction.
  • Define magnetic flux through a surface and give its unit.
  • State Faraday's law of induction and use ε = −N dΦ/dt.
  • List the ways in which the flux through a coil can be changed.

Oersted and Ampere showed that currents produce magnetic fields. The natural question was the reverse: can magnets produce currents? Around 1830 Michael Faraday in England and Joseph Henry in the USA showed that they can - but only when something changes. This electromagnetic induction is the principle behind every generator and transformer that powers modern life. Asked what use his discovery was, Faraday is said to have replied by asking what use a newborn baby is.

The experiments of Faraday and Henry

Three experiments that revealed induction

  • Magnet and coil
    • Coil connected to a galvanometer
    • Magnet pushed in: deflection; pulled out: opposite deflection
    • No deflection while the magnet is still
    • Faster motion gives a larger deflection
    • Moving the coil instead gives the same effects
  • Two coils
    • Second coil carries a steady current from a battery
    • Moving either coil relative to the other induces a current
    • Reversing the motion reverses the current
  • Two coils at rest
    • Pressing a key in the second coil's circuit: brief deflection
    • Key held down (steady current): no deflection
    • Releasing the key: brief opposite deflection
    • An iron rod through the coils greatly increases the effect

The first two experiments suggest that relative motion matters, but the third shows that motion is not essential: a current that is switched on or off, with nothing moving, also induces a current. The common feature, as Faraday realised, is a changing magnetic flux through the coil.

Magnetic flux

For a flat area A in a uniform field B, with the area vector A along the normal, the magnetic flux is:

Φ_B = B · A = BA cos θ, where θ is the angle between B and the normal to the area. For non-uniform fields or curved surfaces, Φ_B = Σ Bᵢ · dAᵢ. Unit: weber (Wb) = T m². Flux is a scalar.

Faraday's law of induction

The magnitude of the emf induced in a circuit equals the time rate of change of magnetic flux through it: ε = −dΦ_B/dt. For a closely wound coil of N turns: ε = −N dΦ_B/dt.

The minus sign gives the direction of the emf (Lenz's law, next lesson). Since Φ = BA cos θ, the flux - and so an emf - can be changed in three ways:

  • Change B: move a magnet or a current-carrying coil, or change a current (Faraday's experiments).
  • Change A: stretch, shrink or reshape a loop in a field, or slide part of a circuit.
  • Change θ: rotate a coil in a field (the principle of the generator, lesson 5).

Explaining the third experiment: pressing the key makes the current in the second coil, and its field, rise from zero in a short time, so the flux through the first coil rises and an emf appears. While the key is held, the current is steady, the flux is constant and the induced emf is zero. Releasing the key makes the flux fall, inducing an emf the other way. (This is also why switching a large electromagnet on or off can damage sensitive instruments nearby.)

From a change to an induced current

  1. Something changes B, the area A, or the angle θ.
  2. Flux changes Φ = BA cos θ through each turn.
  3. Emf induced ε = −N dΦ/dt.
  4. Current in a closed circuit I = ε/R.

Worked example 1: a field that falls

A coil of 200 turns and area 0.01 m² has its normal along a uniform field that falls steadily from 0.5 T to 0.1 T in 0.2 s. The coil's resistance is 8 Ω.

  1. Change of flux per turn: ΔΦ = ΔB × A = (0.5 − 0.1) × 0.01 = 4 × 10⁻³ Wb.
  2. Induced emf: ε = NΔΦ/Δt = 200 × 4 × 10⁻³ ÷ 0.2 = 4 V.
  3. Current: I = ε/R = 4 ÷ 8 = 0.5 A.
  4. Charge that flows: q = IΔt = 0.5 × 0.2 = 0.1 C. Note q = NΔΦ/R, which does not depend on how fast the change happens.

Worked example 2: flipping a coil

A circular coil of 100 turns and radius 5 cm lies with its plane perpendicular to a uniform field of 0.2 T. It is turned through 180° in 0.1 s. Area A = π × (0.05)² ≈ 7.85 × 10⁻³ m². Initial flux per turn = BA; final flux = BA cos 180° = −BA. Change = 2BA = 2 × 0.2 × 7.85 × 10⁻³ ≈ 3.14 × 10⁻³ Wb. Average emf = NΔΦ/Δt = 100 × 3.14 × 10⁻³ ÷ 0.1 ≈ 3.1 V. (The instantaneous emf varies during the turn; this is the average.)

Worked example 3: a field at an angle

A square loop of side 20 cm is in a uniform field of 0.5 T making 60° with its normal. The field is reduced steadily to zero in 0.25 s. Initial flux = BA cos 60° = 0.5 × 0.04 × 0.5 = 0.01 Wb. Average emf = 0.01 ÷ 0.25 = 0.04 V. A steady field such as the earth's, also threading the loop, induces nothing because it does not change.

Key takeaways

  • An emf is induced whenever the magnetic flux through a circuit changes - by motion or by a changing current.
  • Φ = BA cos θ, in webers; ε = −N dΦ/dt.
  • The flux can be changed through B, A or θ; a constant flux induces nothing, however strong.

Check your understanding

  1. 1. In Faraday's experiment with two stationary coils, the galvanometer in the first coil deflects

    1. steadily while the key in the second coil's circuit is held pressed
    2. only at the moments the key is pressed or released
    3. only if the second coil is moved
    4. only if an iron rod is moved through the coils
    Show answer

    Answer: B. An emf is induced only while the flux is changing: when the current in the second coil rises (key pressed) or falls (key released). With a steady current the flux is constant and nothing is induced.

  2. 2. A uniform field of 0.4 T makes an angle of 60° with the normal to a loop of area 0.05 m². What is the flux through the loop?

    1. 0.02 Wb
    2. 0.017 Wb
    3. 0.01 Wb
    4. 0.04 Wb
    Show answer

    Answer: C. Φ = BA cos θ = 0.4 × 0.05 × cos 60° = 0.02 × 0.5 = 0.01 Wb.

  3. 3. The flux through each turn of a 50-turn coil changes from 3 × 10⁻³ Wb to 1 × 10⁻³ Wb in 0.02 s. What is the magnitude of the average induced emf?

    1. 5 V
    2. 0.1 V
    3. 2.5 V
    4. 10 V
    Show answer

    Answer: A. ε = NΔΦ/Δt = 50 × (3 − 1) × 10⁻³ ÷ 0.02 = 50 × 2 × 10⁻³ ÷ 0.02 = 0.1 ÷ 0.02 = 5 V.

  4. 4. A coil of resistance 5 Ω has 100 turns. The flux through each turn changes by 2 × 10⁻³ Wb. How much charge flows through the coil?

    1. 0.4 C
    2. 1 C
    3. 0.01 C
    4. 0.04 C
    Show answer

    Answer: D. q = NΔΦ/R = 100 × 2 × 10⁻³ ÷ 5 = 0.2 ÷ 5 = 0.04 C. The time taken for the change does not matter.

  5. 5. Assertion (A): A very strong but steady magnet held at rest next to a closed loop induces no current in it. Reason (R): An emf is induced only when the magnetic flux through the loop changes.

    1. Both A and R are true, and R is the correct explanation of A
    2. Both A and R are true, but R is not the correct explanation of A
    3. A is true, but R is false
    4. A is false, but R is true
    Show answer

    Answer: A. Both are true. However strong the field, a constant flux gives dΦ/dt = 0 and no emf. R explains A.

Sign in to keep track of the lessons you finish.

Next lesson → Lenz's law and conservation of energy

Privacy · Terms · Refunds · Delivery