- Foundation
- About 24 min
- 5 practice questions
Mutual inductance, self-inductance and magnetic energy
Define inductance as flux linkage per unit current, derive the mutual inductance of two coaxial solenoids and the self-inductance L = μ₀n²Al of a solenoid, and find the energy ½LI² stored in an inductor.
If something looks wrong, please tell us.
By the end of this lesson you can
- Define flux linkage and inductance, with unit the henry.
- Derive the mutual inductance of two long coaxial solenoids and explain M₁₂ = M₂₁.
- Derive the self-inductance of a long solenoid and the back emf ε = −L dI/dt.
- Derive the energy ½LI² and the energy density B²/2μ₀.
A changing current in one coil can induce an emf in a neighbouring coil - and also in itself. Both effects depend only on geometry and materials, and are described by a single kind of quantity: inductance. It plays for currents the role that mass plays for motion.
Flux linkage and inductance
For a coil whose shape does not change, the flux through it due to a current I is proportional to I. For a closely wound coil of N turns the same flux links every turn, so the flux linkage NΦ_B is proportional to I. The constant of proportionality is the inductance. It depends only on the coil's geometry and the material inside it (just as capacitance depends on plate geometry and the dielectric). Inductance is a scalar; its SI unit is the henry (H), with dimensions [M L² T⁻² A⁻²].
Mutual inductance
Two long coaxial solenoids share the same length l. The inner one, S₁, has radius r₁ and n₁ turns per unit length; the outer one, S₂, has radius r₂ and n₂ turns per unit length.
- Current I₂ in S₂ makes a uniform field μ₀n₂I₂ inside S₂.
- The flux through each turn of S₁ is μ₀n₂I₂ × πr₁², and S₁ has n₁l turns, so N₁Φ₁ = μ₀n₁n₂πr₁²l I₂ = M₁₂I₂.
- So M₁₂ = μ₀n₁n₂πr₁²l.
- Now pass I₁ through S₁. Its field μ₀n₁I₁ exists only inside S₁ (area πr₁²), so the flux linkage with the n₂l turns of S₂ is N₂Φ₂ = μ₀n₁n₂πr₁²l I₁, giving M₂₁ = μ₀n₁n₂πr₁²l.
M₁₂ = M₂₁ = M = μ₀n₁n₂πr₁²l for coaxial solenoids (μrμ₀n₁n₂πr₁²l with a core of relative permeability μr). Induced emf in coil 1: ε₁ = −M dI₂/dt.
The equality M₁₂ = M₂₁ holds in general, which is very useful: if one of the two calculations is hard, do the easy one. M depends on the coils' separation and relative orientation as well as their sizes. For example, a small coil of radius r₁ at the centre of a large coaxial coil of radius r₂ (r₁ ≪ r₂) sits in the nearly uniform field μ₀I₂/(2r₂) of the large coil, giving M = μ₀πr₁²/(2r₂).
Self-inductance
A changing current in a coil changes the flux through the coil itself, inducing an emf in it. This is self-induction. With NΦ_B = LI:
ε = −L dI/dt. For a long solenoid of n turns per unit length, cross-section A and length l: L = μ₀n²Al (μrμ₀n²Al with a core).
Derivation: B = μ₀nI inside; flux linkage = (nl)(μ₀nI)(A) = μ₀n²Al I, so L = μ₀n²Al. A soft iron core with large μr multiplies L enormously. The self-induced emf is called the back emf because it always opposes the change in current - whether the current is rising or falling.
Self-inductance and mass
-
Inductance L
- Opposes change of current
- Back emf L dI/dt
- Stored energy ½LI²
- Electrical inertia
-
Mass m
- Opposes change of velocity
- Force m dv/dt
- Kinetic energy ½mv²
- Mechanical inertia
Energy stored in an inductor
To build up a current, work must be done against the back emf. At an instant when the current is I, the rate of work is dW/dt = |ε| I = L I dI/dt (ignoring resistance). Adding up from 0 to the final current: W = ∫ L I dI = ½LI². This energy is stored in the magnetic field.
U = ½LI². For a solenoid, using L = μ₀n²Al and B = μ₀nI: U = (B²/2μ₀) Al, so the magnetic energy density is u_B = B²/(2μ₀).
Compare the electric energy density ½ε₀E²: in both cases energy is proportional to the square of the field. Both results, though derived for a solenoid and a capacitor, hold for any region containing a field. When two coils carry currents together, the emf in coil 1 is ε₁ = −L₁ dI₁/dt − M₁₂ dI₂/dt.
Worked example 1: two coaxial solenoids
An inner solenoid (2000 turns per metre, radius 1 cm) sits inside an outer one (1000 turns per metre); both are 0.5 m long. M = μ₀n₁n₂πr₁²l = 4π × 10⁻⁷ × 2000 × 1000 × π × (0.01)² × 0.5 ≈ 3.9 × 10⁻⁴ H. If the outer current changes at 50 A s⁻¹, the emf in the inner coil is M dI/dt = 3.9 × 10⁻⁴ × 50 ≈ 0.02 V.
Worked example 2: self-inductance and energy
A solenoid has 500 turns over 0.25 m (n = 2000 m⁻¹) and cross-section 4 × 10⁻⁴ m², with air inside. L = μ₀n²Al = 4π × 10⁻⁷ × (2000)² × 4 × 10⁻⁴ × 0.25 ≈ 5.0 × 10⁻⁴ H. At 2 A it stores U = ½LI² = ½ × 5.0 × 10⁻⁴ × 4 = 1.0 × 10⁻³ J. If the current is cut to zero in 1 ms, the average back emf is L ΔI/Δt = 5.0 × 10⁻⁴ × 2 ÷ 10⁻³ ≈ 1.0 V.
Worked example 3: inductance from a measured emf
When the current in a circuit falls steadily from 4 A to zero in 0.02 s, an average emf of 50 V is induced. L = ε Δt/ΔI = 50 × 0.02 ÷ 4 = 0.25 H. The energy released is ½ × 0.25 × 4² = 2 J. The energy density in a field of 0.5 T is u = B²/(2μ₀) = 0.25 ÷ (2 × 4π × 10⁻⁷) ≈ 1.0 × 10⁵ J m⁻³.
Key takeaways
- Inductance = flux linkage per unit current (henry).
- Coaxial solenoids: M = μ₀n₁n₂πr₁²l; M₁₂ = M₂₁; ε₁ = −M dI₂/dt.
- Solenoid: L = μ₀n²Al (× μr with a core); back emf ε = −L dI/dt.
- Energy ½LI²; magnetic energy density B²/2μ₀.
Check your understanding
-
1. What is the SI unit of inductance?
- weber
- tesla
- henry
- farad
Show answer
Answer: C. Inductance is flux linkage per unit current, Wb A⁻¹, which is named the henry (H).
-
2. The current in a coil changes from 6 A to 2 A in 0.1 s and an average emf of 8 V is induced in it. What is its self-inductance?
- 0.2 H
- 0.13 H
- 5 H
- 0.4 H
Show answer
Answer: A. L = ε Δt/ΔI = 8 × 0.1 ÷ (6 − 2) = 0.8 ÷ 4 = 0.2 H.
-
3. Two adjacent coils have mutual inductance 0.5 H. The current in one rises from 0 to 10 A in 0.25 s. What is the change of flux linkage with the other coil?
- 20 Wb
- 1.25 Wb
- 2.5 Wb
- 5 Wb
Show answer
Answer: D. Change in flux linkage = M ΔI = 0.5 × 10 = 5 Wb. (The average emf would be 5 ÷ 0.25 = 20 V.)
-
4. If the number of turns of a long solenoid is doubled, keeping its length and area the same, its self-inductance becomes
- twice as large
- four times as large
- half as large
- unchanged
Show answer
Answer: B. L = μ₀n²Al. Doubling the turns on the same length doubles n, so L increases by 2² = 4.
-
5. Assertion (A): Self-inductance is sometimes called electrical inertia. Reason (R): The back emf in a coil opposes any change in the current through it, as inertia opposes a change in velocity.
- Both A and R are true, and R is the correct explanation of A
- Both A and R are true, but R is not the correct explanation of A
- A is true, but R is false
- A is false, but R is true
Show answer
Answer: A. Both are true, and R explains A: ε = −L dI/dt resists changes in current just as m dv/dt resists changes in velocity, and the stored energy ½LI² mirrors ½mv².
Sign in to keep track of the lessons you finish.