- Foundation
- About 25 min
- 15 practice questions
Final self-assessment: Electric circuits and their components
Test yourself on the whole course: 15 questions with answers explained.
If something looks wrong, please tell us.
Attempt all 15 questions in one sitting, writing down your reasoning for each one before you look at the answers. The questions mix ideas from all five lessons and are a little harder than the lesson checks. When you finish, read every explanation, including those for the questions you got right.
Final self-assessment
-
1. A torch has three cells. For it to work, how must they be placed?
- The positive terminal of each cell touching the negative terminal of the next
- All metal caps facing the same flat disc of the switch
- Two cells + to −, and the third reversed
- Negative terminals touching each other
Show answer
Answer: A. Cells in a battery are joined + to − throughout. Reversing any one cell makes it oppose the others.
-
2. The label on a torch cell has peeled off. How can you tell which end is the positive terminal?
- The flat metal disc is always positive
- Touch both ends with wet fingers
- Plug the cell into a wall socket
- The end with the small metal cap that sticks out is positive
Show answer
Answer: D. On a common torch cell the protruding metal cap is the positive terminal and the flat disc is negative. Wet fingers and wall sockets are never safe ways to test.
-
3. Which of these is used for experiments with electricity at school?
- A plug in a wall socket
- A battery of torch cells
- An extension board
- A portable generator
Show answer
Answer: B. Only cells and batteries are safe for experiments. Mains supply and generators can cause serious injury.
-
4. An incandescent lamp is connected correctly to a working cell but does not glow. What is the most likely cause?
- The filament is broken
- The lamp is connected the wrong way round
- The cell has too much energy
- The glass is clean
Show answer
Answer: A. An incandescent lamp works whichever way it is connected. If it does not glow in a correct circuit, it is probably fused, with a broken filament.
-
5. Which statement correctly compares an LED and an incandescent lamp?
- Both have filaments and work either way
- An LED has a filament; an incandescent lamp does not
- An LED has no filament and works only one way round; an incandescent lamp has a filament and works either way
- Both work only one way round
Show answer
Answer: C. An LED has no filament and conducts in one direction only. An incandescent lamp's filament glows whichever way the current flows through it.
-
6. Which change would make a reversed LED glow in a circuit?
- Adding a plastic strip between the wires
- Swapping the two wires connected to the LED
- Opening the switch
- Removing the battery
Show answer
Answer: B. Swapping the wires puts the longer leg on the positive side, allowing current through the LED in its one allowed direction.
-
7. A torch-style loop has a cell, a lamp, a second lamp, and two switches marked M and N. M is ON and N is OFF. Which lamps glow?
- Only the first lamp
- Only the second lamp
- Both lamps
- Neither lamp
Show answer
Answer: D. There is only one path, and switch N being OFF breaks it. No current flows anywhere in the loop.
-
8. A circuit is complete, but a student moves the switch from next to the cell to the other side of the lamp. The switch is ON. Does the lamp glow?
- No, because a switch must always be next to the cell
- No, because current flows only from the switch
- Only if the lamp is an LED
- Yes, because a switch can be placed anywhere in the circuit
Show answer
Answer: D. A switch simply closes or opens the path. In a simple loop, its position does not matter; when ON the circuit is complete.
-
9. What is the job of a switch in a circuit?
- To produce electricity
- To complete or break the circuit as needed
- To store electricity
- To make the lamp shine brighter
Show answer
Answer: B. A switch closes the gap (ON) or opens it (OFF); the cell is the source of electricity.
-
10. In a circuit diagram, an LED symbol's triangle points from the − side of the battery towards the + side. The switch is closed. What happens?
- The LED glows brightly
- The battery stops working permanently
- The LED does not glow, because it is connected in the reverse direction
- The switch opens by itself
Show answer
Answer: C. Current flows from + to − in the outside circuit. The triangle must point in that direction; pointing the other way, the LED blocks the current.
-
11. In a cell symbol, which line is the negative terminal?
- The shorter, thicker line
- The longer, thinner line
- The line through the middle of the circle
- The arrow pointing outwards
Show answer
Answer: A. The long line stands for the positive terminal and the short line for the negative terminal.
-
12. Which list contains ONLY conductors?
- Copper wire, rubber band, iron nail
- Copper wire, iron nail, aluminium foil
- Glass, plastic, wood
- Aluminium foil, wax, steel spoon
Show answer
Answer: B. Copper, iron and aluminium are metals and conduct electricity. Rubber, glass, plastic, wood and wax are insulators.
-
13. Why are the pins of a plug made of metal while the plug top is made of plastic?
- The pins must conduct current; the top must insulate the user's hand
- Metal is cheaper than plastic
- Plastic conducts better than metal
- The pins must stop current from flowing
Show answer
Answer: A. The pins carry current into the appliance, so they must be conductors. The top is held by hand, so it must be an insulator.
-
14. A drawer has four torch cells, and some are used up. Which plan finds the working ones fairly?
- Connect all four together and see if a lamp glows
- Look at the colour of each cell
- Use a different lamp and wire for each cell
- Put each cell in turn into the same circuit with the same working lamp and see whether the lamp glows
Show answer
Answer: D. Testing each cell alone in the same circuit, with a lamp known to work, changes only the cell. If the lamp glows, that cell is working.
-
15. Why should switches never be touched with wet hands?
- Water makes the switch an insulator
- Wet hands make the bulb fuse
- Water and the human body conduct electricity, so a shock is more likely
- It is only a matter of keeping switches clean
Show answer
Answer: C. Our body conducts electricity and impure water helps current pass, so wet hands increase the risk of a dangerous shock.
Questions 1-3: lesson 1 (cells, batteries and safety). Questions 4-6: lesson 2 (incandescent lamps and LEDs). Questions 7-9: lesson 3 (circuits and switches). Questions 10-11: lesson 4 (circuit diagrams). Questions 12-15: lesson 5 (conductors, insulators and safety).
Sign in to keep track of the lessons you finish.