- Foundation
- About 14 min
- 5 practice questions
Making water safe to drink: water treatment and sewage treatment
Describe the stages of purifying river water for drinking and of treating sewage, and calculate simple chlorine and alum doses in ppm and grams.
If something looks wrong, please tell us.
Water taken from a river or lake carries mud, floating waste, dissolved salts and disease-causing germs. Sewage leaving our homes carries food waste, soap and faecal matter. Before the first can be drunk and the second returned to a river, chemistry and biology have to do some work. In this lesson you will follow both journeys step by step and then do the small calculations that exam questions ask about.
Treating water for drinking
A water works removes impurities in a fixed order, from the biggest particles to the smallest and finally to the germs.
- Screening: bars and nets stop leaves, plastic and other large floating objects.
- Sedimentation: the water rests in a large tank and heavy sand and silt settle to the bottom.
- Coagulation: a little alum (potash alum, K₂SO₄·Al₂(SO₄)₃·24H₂O, or aluminium sulphate) is added. It forms a jelly-like precipitate of aluminium hydroxide, Al(OH)₃, called a floc, which traps very fine clay and bacteria and carries them down as it settles.
- Filtration: the clear water trickles through beds of sand and gravel, which hold back what is left.
- Disinfection: a small amount of chlorine gas or bleaching powder is added to kill germs. Ozone and ultraviolet light do the same job without chlorine's taste.
At home the simplest disinfection is boiling for a few minutes. Boiling kills germs but does not remove dissolved chemicals such as fertiliser nitrate.
Why chlorine, and how much
Chlorine reacts with water to give hypochlorous acid, HOCl, which destroys the cell walls of germs: Cl₂ + H₂O → HOCl + HCl. Enough is added so that a little residual chlorine stays in the water, protecting it all the way along the pipes. Too much gives a bad taste and smell. Doses are tiny and are written in parts per million (ppm): 1 ppm in water means 1 mg of substance in 1 litre.
1 ppm in water = 1 mg per litre. Mass needed = dose in mg per litre × volume in litres. Divide by the purity fraction if the chemical is not pure.
Worked example 1: chlorine dose. A storage tank holds 20,000 litres of water and the dose is 2 ppm (illustrative value). Chlorine needed = 2 mg/L × 20,000 L = 40,000 mg = 40 g. If bleaching powder is used and we suppose it holds 30% available chlorine (illustrative), the powder needed is 40 g / 0.30 = 133.3 g, about 133 g.
Worked example 2: alum dose. A treatment tank holds 50,000 litres and the alum dose is 25 mg per litre (illustrative). Alum needed = 25 × 50,000 = 12,50,000 mg = 1,250 g = 1.25 kg.
Treating sewage
Sewage is treated in three stages before the water goes back to a river or is used for gardens.
- Primary treatment (physical): screens remove rags and plastics, grit settles, and in a settling tank the solids sink as sludge while oil and grease are skimmed off.
- Secondary treatment (biological): air is blown through the liquid so that bacteria and other micro-organisms feed on the dissolved organic matter. This lowers the BOD of the water. The settled microbial mass is called activated sludge.
- Tertiary treatment (advanced): removes what is left, such as nitrates and phosphates, and disinfects the water with chlorine or ultraviolet light.
Sludge from the tanks is kept without air in a digester. Bacteria break it down and give biogas, mostly methane, which can be burnt as a fuel, while the remaining solid can be dried for use as manure.
Worked example 3: place the stage. (a) Removing floating plastic bottles from sewage is primary treatment, because it is a physical step. (b) Bacteria eating dissolved sugars in the sewage is secondary treatment. (c) Killing the germs in the final water with chlorine is tertiary treatment (or disinfection). (d) Alum forming a floc in drinking water is coagulation, part of water treatment, not of sewage treatment.
Key takeaways
- Drinking water: screening, sedimentation, coagulation with alum, filtration, disinfection.
- Chlorine doses are measured in ppm: 1 ppm = 1 mg per litre.
- Sewage: primary is physical, secondary uses bacteria and air, tertiary removes nutrients and germs.
- Sludge digestion gives biogas.
Check your understanding
-
1. Which chemical is added to water so that tiny suspended particles clump together and settle?
- Alum
- Washing soda
- Common salt
- Slaked lime
Show answer
Answer: A. Alum forms a gelatinous precipitate of aluminium hydroxide that traps fine particles. This step is called coagulation.
-
2. In which stage of sewage treatment do bacteria and air remove dissolved organic matter?
- Primary treatment
- Secondary treatment
- Tertiary treatment
- Screening
Show answer
Answer: B. The biological step, in which micro-organisms feed on dissolved organic matter in aerated tanks, is secondary treatment.
-
3. A tank holds 10,000 litres of water. How much chlorine gives a dose of 3 ppm?
- 3 g
- 60 g
- 30 g
- 300 g
Show answer
Answer: C. 3 ppm = 3 mg per litre. 3 mg × 10,000 L = 30,000 mg = 30 g.
-
4. Which stage of drinking-water treatment comes immediately before disinfection?
- Coagulation
- Screening
- Filtration
- Aeration
Show answer
Answer: C. The order is screening, sedimentation, coagulation, filtration, then disinfection. Water is filtered first so that the disinfectant is not wasted on mud.
-
5. What useful fuel gas is produced when sewage sludge is kept in a closed digester?
- Methane
- Hydrogen
- Oxygen
- Carbon monoxide
Show answer
Answer: A. Anaerobic bacteria turn the organic matter in sludge into biogas, which is mostly methane.
Sign in to keep track of the lessons you finish.