• Foundation
  • About 13 min
  • 5 practice questions

Measuring what is in water: ppm, mg/L, total dissolved solids and simple dilution

Express small concentrations in mg/L and ppm, find total dissolved solids by evaporation, and calculate masses dissolved in a tank of water.

If something looks wrong, please tell us.

Almost everything harmful or useful in water is present in tiny amounts. Dissolved oxygen, fluoride, hardness salts and pollutants are all measured in units for very small concentrations. Without these units a water-quality report cannot be read. This lesson explains milligrams per litre and parts per million, shows how total dissolved solids are measured, and uses the units in everyday calculations.

Small concentrations

A milligram per litre (mg/L) is one thousandth of a gram of substance in each litre of water. A part per million (ppm) means one part of the substance in a million parts of the solution by mass. Since 1 L of dilute aqueous solution has a mass of about 1,000,000 mg, 1 mg per litre is 1 part in a million. So for water, 1 ppm = 1 mg/L. Percentage is parts per hundred, so 1% = 10,000 ppm and 0.01% = 100 ppm.

Units for small amounts
UnitMeaningEquivalent
mg/Lmilligrams of solute in 1 litre of water1 mg/L = 1 ppm for water
ppmparts per million by mass1 ppm = 0.0001%
Percentageparts per hundred1% = 10,000 ppm
g/Lgrams per litre1 g/L = 1000 mg/L = 1000 ppm

Total dissolved solids

Total dissolved solids (TDS) is the total mass of all dissolved substances in a litre of water. It can be measured by taking a known volume of clear water, evaporating it carefully to dryness, and weighing the solid that remains. Dissolved ions also make water conduct electricity, so a conductivity meter gives a quick estimate of TDS. A high TDS may mean salty or hard water, but TDS says nothing about which substances are present, so a low TDS does not prove the water is safe.

Worked example 1: salt solution

0.5 g of salt is dissolved in 2 L of water. Step 1: change to milligrams: 0.5 g = 500 mg. Step 2: divide by volume: 500 ÷ 2 = 250 mg/L. Step 3: for water, 250 mg/L = 250 ppm.

Worked example 2: total dissolved solids

500 mL of a clear water sample is evaporated to dryness and leaves 0.15 g of solid. Step 1: 0.15 g = 150 mg. Step 2: 500 mL = 0.5 L. Step 3: TDS = 150 ÷ 0.5 = 300 mg/L = 300 ppm.

Worked example 3: mass in a tank

A fish tank holds 5000 L of water with a dissolved oxygen concentration of 6 mg/L. Step 1: mass of oxygen = 6 × 5000 = 30,000 mg. Step 2: 30,000 mg = 30 g. Cold water holds more dissolved oxygen than warm water, so a warm tank has less.

Worked example 4: a small sample

A 40 L sample of river water contains 20 mg of a pollutant. Step 1: concentration = 20 ÷ 40 = 0.5 mg/L. Step 2: in ppm this is 0.5 ppm. Pollutants such as heavy metals can be harmful at concentrations of this size, which is why very small concentrations need careful measurement.

Judging a reported value

Authorities set permitted limits for substances in drinking water. A limit does not mean that anything below it is wanted, nor that anything above it kills at once. It is a safety boundary. Some substances are needed in small amounts and harmful in excess, such as fluoride; others are harmful at any detectable level. A report that gives numbers without units is useless, so always check whether the figure is in mg/L, ppm or percent.

For water, 1 ppm = 1 mg/L. 1% = 10,000 ppm. Mass of solute = concentration (mg/L) × volume (L). TDS = mass of residue ÷ volume of sample.

Key takeaways

  • ppm and mg/L mean the same for dilute aqueous solutions.
  • Convert grams to milligrams (×1000) and keep the volume in litres.
  • TDS is found by evaporating a known volume and weighing the residue.
  • Limits for drinking water are set by authorities; check units when you read a report.

Check your understanding

  1. 1. 0.5 g of salt dissolved in 2 L of water gives a concentration of:

    1. 25 mg/L
    2. 2.5 mg/L
    3. 1000 mg/L
    4. 250 mg/L
    Show answer

    Answer: D. 0.5 g = 500 mg; 500 mg ÷ 2 L = 250 mg/L = 250 ppm.

  2. 2. 500 mL of water leaves a residue of 0.15 g on evaporation. The TDS is:

    1. 30 mg/L
    2. 75 mg/L
    3. 300 mg/L
    4. 3000 mg/L
    Show answer

    Answer: C. Residue = 150 mg; volume = 0.5 L; TDS = 150 ÷ 0.5 = 300 mg/L.

  3. 3. A 5000 L tank has dissolved oxygen of 6 mg/L. The mass of dissolved oxygen is:

    1. 3 g
    2. 30 g
    3. 300 g
    4. 30 mg
    Show answer

    Answer: B. 6 mg/L × 5000 L = 30,000 mg = 30 g.

  4. 4. 0.01% by mass of a substance in water is equivalent to:

    1. 100 ppm
    2. 1 ppm
    3. 10 ppm
    4. 1000 ppm
    Show answer

    Answer: A. 1% = 10,000 ppm, so 0.01% = 100 ppm.

  5. 5. A 40 L sample contains 20 mg of a pollutant. Its concentration is:

    1. 20 mg/L
    2. 800 mg/L
    3. 0.5 mg/L
    4. 2 mg/L
    Show answer

    Answer: C. 20 mg ÷ 40 L = 0.5 mg/L = 0.5 ppm.

Privacy · Terms · Refunds · Delivery