• Foundation
  • About 14 min
  • 5 practice questions

Using water wisely: sewage treatment, rainwater harvesting and desalination

Describe the stages of sewage treatment, calculate the water a roof can collect, and compare distillation and reverse osmosis as ways of making fresh water from salty water.

If something looks wrong, please tell us.

Fresh water is limited, so much of water chemistry is about getting more use out of it. Cities treat their used water so it can be returned safely to rivers. Houses can collect rain. Where only sea water is available, it can be turned into drinking water at some cost. This lesson describes each approach, gives a few simple calculations, and explains why each method is chosen for its purpose.

Sewage treatment

Sewage is used water from homes and industries. It contains solid waste, organic matter, germs, and dissolved nutrients such as nitrates and phosphates. Left untreated, it would cause a high BOD, kill fish and cause eutrophication. Treatment works in stages.

  1. Preliminary and primary treatment: screens and grit chambers remove large objects and sand; the water then stands in tanks where solids settle as sludge and oil floats and is skimmed off. This stage removes solids, not dissolved matter.
  2. Secondary treatment: air is bubbled through the water so that microbes can feed on the organic matter and break it down, which reduces the BOD. The microbes settle as sludge.
  3. Tertiary treatment: further steps, such as filtering, removing nutrients, and disinfection with chlorine, ozone or ultraviolet light, make the water safe to discharge or reuse.

The sludge from several stages can be broken down by bacteria in closed tanks without air, which gives a gas rich in methane that can be used as fuel.

Rainwater harvesting

In rainwater harvesting, rain falling on roofs is led by pipes into tanks or into the ground, so it can be stored for use or can recharge groundwater. The volume collected is the roof area times the rainfall depth, reduced by losses. Rain collected from a clean roof is soft, but the first water that falls washes dust off the roof and is often discarded.

Worked example 1: water from a roof

A roof has an area of 50 m². During a rainstorm the depth of rainfall is 100 mm (an illustrative figure). Step 1: depth in metres = 0.1 m. Step 2: volume = 50 × 0.1 = 5 m³. Step 3: 5 m³ = 5000 L. Step 4: if only 80% of this is captured, the water collected = 5000 × 0.80 = 4000 L.

Desalination

Sea water cannot be drunk because of its high dissolved salt content. Two methods make fresh water from it. In distillation the water is boiled and the steam is condensed, so the salts are left behind and the condensed water is almost pure. In reverse osmosis pressure greater than the osmotic pressure forces the water through a semipermeable membrane and leaves the salts behind. Distillation needs a great deal of heat, because evaporating water requires its latent heat; reverse osmosis uses mainly the energy to run a pump at high pressure.

Worked example 2: heat for distillation

How much heat is needed to evaporate 10 L of water (10 kg), already at 100 °C, in a still? Step 1: Q = m × L. Step 2: with L = 22.6 × 10⁵ J/kg, Q = 10 × 22.6 × 10⁵ = 2.26 × 10⁷ J. Step 3: that is 22,600 kJ, and the figure does not include the heat to bring the water up to 100 °C first. The size of this number explains why distillation is expensive at large scale.

Worked example 3: choosing the method

For each situation choose a method. (a) A river carrying mud and some germs: settling, coagulation with alum, sand filtration and chlorination. (b) A laboratory needing very pure water: distillation. (c) Brackish well water with too many dissolved salts, in a village with electricity: reverse osmosis. (d) Used water from a town: sewage treatment in stages, then disinfection. The method is chosen to match what must be removed.

Sewage: primary removes solids, secondary uses microbes to cut BOD, tertiary polishes and disinfects. Harvested volume = roof area × rainfall depth × capture fraction. Distillation needs heat; reverse osmosis needs pressure.

Key takeaways

  • Sewage is treated in stages: solids first, then microbes for organic matter, then disinfection.
  • Rainwater harvesting stores rain or recharges groundwater.
  • Distillation and reverse osmosis remove dissolved salts.
  • Choose a method by asking what has to be removed.

Check your understanding

  1. 1. In sewage treatment, microbes break down organic matter and lower the BOD in which stage?

    1. Primary treatment
    2. Secondary treatment
    3. Screening
    4. Skimming of oil
    Show answer

    Answer: B. Secondary (biological) treatment uses air and microbes to oxidise organic matter, lowering the BOD.

  2. 2. A roof of area 50 m² receives 100 mm of rain. If 80% is captured, the volume collected is:

    1. 5000 L
    2. 500 L
    3. 4000 L
    4. 40,000 L
    Show answer

    Answer: C. Total volume = 50 × 0.1 = 5 m³ = 5000 L; 80% of that is 4000 L.

  3. 3. Which method forces water through a semipermeable membrane using high pressure to remove salts?

    1. Reverse osmosis
    2. Distillation
    3. Filtration through sand
    4. Coagulation with alum
    Show answer

    Answer: A. Reverse osmosis applies pressure above the osmotic pressure, driving water through the membrane.

  4. 4. Heat to evaporate 10 kg of water already at 100 °C (L = 22.6 × 10⁵ J/kg) is:

    1. 2.26 × 10⁶ J
    2. 2.26 × 10⁷ J
    3. 2.26 × 10⁵ J
    4. 4.2 × 10⁴ J
    Show answer

    Answer: B. Q = 10 × 22.6 × 10⁵ = 2.26 × 10⁷ J.

  5. 5. Distilled water is almost pure because:

    1. Germs are all killed by filtration
    2. Chlorine is added during boiling
    3. Dissolved salts stay behind as water evaporates
    4. Alum is mixed in and removes the salts
    Show answer

    Answer: C. When water boils, the dissolved salts do not form vapour, so the condensed steam is almost free of them.

Privacy · Terms · Refunds · Delivery