Revision notes

Chapter 3 Current Electricity: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Potential difference, free electrons and electric current

How a cell makes current flow in a wire

  1. Chemical reactions in the cell Create a potential difference between its terminals.
  2. Wire joined across the cell An electric force now acts on the free electrons.
  3. Electrons drift From the negative terminal, through the wire, towards the positive terminal.
  4. Current flows Charge passes every cross-section of the wire.

Potential difference V = W/Q (1 V = 1 J/C). Current I = Q/t (1 A = 1 C/s). Electrons move from − to +; conventional current is taken from + to −.

Key takeaways: charge flows because of a potential difference, just as water flows because of a difference in level. Free electrons carry the charge in metals. Current is charge per second; potential difference is work per unit charge.

Read the full lesson

Lesson 2

Electric circuits and Ohm's law

ComponentUse in the circuit
Electric cellProvides a potential difference (long line +, short line −)
BatterySeveral cells together, for a larger potential difference
Plug key or switch (open / closed)Breaks or completes the circuit
Connecting wireJoins components
BulbShows whether current is flowing
ResistorControls the current
Variable resistor (rheostat)Changes the resistance, and so the current
AmmeterMeasures current; connected in series
VoltmeterMeasures potential difference; connected in parallel

Ohm's law: if the physical state of a conductor stays the same, the current I through it is directly proportional to the potential difference V across its ends. V = IR, where R is the resistance of the conductor.

Made-up sample readings for a nichrome wire
Cells usedPotential difference V (volt)Current I (ampere)V/I (ohm)
11.50.1015
23.00.2015
34.50.3015
46.00.4015

Steps in verifying Ohm's law

  1. Build the series circuit Cell, key, ammeter and nichrome wire; voltmeter across the wire.
  2. Record V and I For one cell, then two, three and four cells.
  3. Calculate V/I It comes out the same each time.
  4. Plot I against V A straight line through the origin confirms I ∝ V.

Key takeaways: a circuit is a complete conducting path; ammeters go in series and voltmeters in parallel. Ohm's law says V = IR as long as the conductor's length, thickness, temperature and material do not change. One ohm is one volt per ampere.

Read the full lesson

Lesson 3

Resistance, resistivity, conductors and insulators

Nichrome's resistivity is about 65 times that of copper
MaterialResistivity (Ω m), approximateTypical use
Copper1.7 × 10⁻⁸Connecting wires and cables
Nichrome (an alloy)1.1 × 10⁻⁶Heating coils in irons and heaters
Glass, rubber, dry woodExtremely highInsulation, handles, supports

Conductors and insulators

  • Conductors
    • Very low resistance
    • Many free electrons
    • Copper, aluminium, silver, graphite
    • Used for wires and terminals
  • Insulators
    • Extremely high resistance
    • Almost no free electrons
    • Rubber, plastic, glass, porcelain
    • Used for coverings, handles and supports

R = ρL/A: resistance increases with length, decreases with area of cross-section, and depends on the material through its resistivity ρ (unit Ω m).

Key takeaways: resistance comes from electrons colliding with atoms and ions. A long, thin wire of a high-resistivity alloy like nichrome makes a good heating element; short, thick copper wires make good connectors. Insulators protect us by keeping current inside its intended path.

Read the full lesson

Lesson 4

Resistors in series and in parallel

Series and parallel at a glance

  • Series
    • One path; same current in each
    • Potential differences add up
    • Rs = R₁ + R₂ + R₃
    • Rs is more than the largest
    • One break stops everything
  • Parallel
    • Several paths; same potential difference across each
    • Currents add up
    • 1/Rp = 1/R₁ + 1/R₂ + 1/R₃
    • Rp is less than the smallest
    • Others keep working if one fails

Series: Rs = R₁ + R₂ + R₃, same current. Parallel: 1/Rp = 1/R₁ + 1/R₂ + 1/R₃, same potential difference.

Key takeaways: in series the current is common and the voltages add; in parallel the voltage is common and the currents add. Series raises resistance, parallel lowers it. Always check your answer: the series total must be bigger than every part, and the parallel total smaller than every part.

Read the full lesson

Lesson 5

Electricity at home: wiring, fuses and safety

WireUsual insulation colourJob
Live wireRed or brownBrings the current in
Neutral wireBlue or blackCarries the current back
Earth wireGreen or yellowSafety: connected to a metal plate buried deep in the ground near the house

Path of electricity into a home

  1. Pole or underground cable Live, neutral and earth wires
  2. Fuse and electricity meter Protection and measuring the energy used
  3. Main switch Cuts off the whole house at once
  4. Separate room circuits Each with appliances in parallel between live and neutral

Live (red/brown) brings current in, neutral (blue/black) takes it back, earth (green/yellow) is for safety. Appliances go in parallel; the fuse goes in series and melts when the current is too large.

Key takeaways: household appliances are wired in parallel so each gets the full supply voltage and can be used independently. A fuse in series protects the circuit by melting when the current exceeds its limit. The earth wire and simple habits like dry hands and unplugging before cleaning keep us safe.

Read the full lesson

Privacy · Terms · Refunds · Delivery