• Practice
  • About 15 min
  • 5 practice questions

Electricity at home: wiring, fuses and safety

Describe the live, neutral and earth wires of household wiring, explain why appliances are connected in parallel and why a fuse is connected in series, and follow the safety rules for using electricity.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Name the three wires that bring electricity into a house and their usual colours.
  • Explain why household appliances are connected in parallel.
  • Describe how a fuse wire protects a circuit and use Ohm's law to decide whether a fuse will melt.
  • List the precautions to take while using electricity and what to do if someone gets a shock.

Everything learnt so far about current, Ohm's law and parallel connections is used every day in the wiring of our homes. Knowing how it works also helps us use electricity safely.

The three wires

Electricity reaches a house through a main cable, either from an electric pole or from an underground cable. The cable usually has three wires:

WireUsual insulation colourJob
Live wireRed or brownBrings the current in
Neutral wireBlue or blackCarries the current back
Earth wireGreen or yellowSafety: connected to a metal plate buried deep in the ground near the house

In India the potential difference between the live and neutral wires is about 220 V. The live and neutral wires pass through a fuse to the electricity meter and then, through a main switch, to the wiring of every room. Each appliance is connected between the live and neutral wires.

Path of electricity into a home

  1. Pole or underground cable Live, neutral and earth wires
  2. Fuse and electricity meter Protection and measuring the energy used
  3. Main switch Cuts off the whole house at once
  4. Separate room circuits Each with appliances in parallel between live and neutral

Why appliances are connected in parallel

  • Each appliance gets the same full potential difference of the supply, so each works at its intended voltage.
  • Each appliance has its own path and its own switch, so it can be turned on or off independently; if the TV stops working, the fan and lights continue.
  • Each appliance draws a current that depends on its own resistance (I = V/R), and the total current from the supply is the sum of these currents.

If appliances were in series, they would share the voltage, none would get the full 220 V, and one failure or one switch turned off would stop all of them, just like a cheap string of decorative bulbs that goes dark when one bulb fails.

The fuse

A fuse wire is made of a material with a low, definite melting point and is fitted in a holder of porcelain-like insulating material. It is connected in series in the circuit it protects. If the current becomes too large, for example because too many appliances are switched on together or because of a short circuit, the fuse wire heats up and melts, breaking the circuit and stopping the current before the wiring or the appliances are damaged. Fuse wires are made for different upper limits of current, such as 1 A, 2 A, 5 A or 10 A, and the right one is chosen for each circuit. Cartridge fuses and ceramic fuses are common types.

Worked example 1: will the fuse melt?

Question: A room circuit at 220 V has a 5 A fuse. A lamp of resistance 1100 Ω and a heater of resistance 55 Ω are switched on. Then a second 55 Ω heater is switched on. What happens?

Working: All are in parallel across 220 V. Lamp: I = 220 ÷ 1100 = 0.2 A. Each heater: I = 220 ÷ 55 = 4 A. Lamp + one heater = 4.2 A, below 5 A, so the fuse holds. With the second heater the total is 0.2 + 4 + 4 = 8.2 A, above 5 A, so the fuse melts and the circuit is cut off.

Worked example 2: currents in a kitchen circuit

Question: A mixer of resistance 440 Ω and an electric kettle of resistance 44 Ω work on the same 220 V circuit. Find the current through each and the total current.

Working: Mixer: 220 ÷ 440 = 0.5 A. Kettle: 220 ÷ 44 = 5 A. Total = 5.5 A. The kettle, with one tenth of the resistance, draws ten times the current.

Precautions while using electricity

  1. Switches and sockets should be fitted high enough that small children cannot push pins or nails into them.
  2. Remove a plug by holding the plug itself, never by pulling its wire.
  3. Switch off and unplug an appliance before cleaning it.
  4. Handle electrical appliances only with dry hands, and preferably wear rubber-soled footwear, since rubber is an insulator.
  5. If someone gets an electric shock, do not touch the person. Switch off the main switch, or pull out the plug if possible; otherwise push the person away from the wire with a dry wooden pole.

Live (red/brown) brings current in, neutral (blue/black) takes it back, earth (green/yellow) is for safety. Appliances go in parallel; the fuse goes in series and melts when the current is too large.

Key takeaways: household appliances are wired in parallel so each gets the full supply voltage and can be used independently. A fuse in series protects the circuit by melting when the current exceeds its limit. The earth wire and simple habits like dry hands and unplugging before cleaning keep us safe.

Check your understanding

  1. 1. What is the usual insulation colour of the earth wire in household wiring?

    1. Red or brown
    2. Blue or black
    3. Green or yellow
    4. White
    Show answer

    Answer: C. The live wire is usually red or brown, the neutral wire blue or black, and the earth wire green or yellow.

  2. 2. Why are household appliances connected in parallel?

    1. So that each gets the same supply voltage and can be switched on or off independently
    2. So that the same current flows through all of them
    3. So that the total resistance of the house increases
    4. So that one switch controls every appliance
    Show answer

    Answer: A. In parallel, every appliance is directly across the live and neutral wires, so each gets the full supply voltage and has its own path. One appliance can be turned off or fail without affecting the others.

  3. 3. How is a fuse wire connected in a circuit, and why?

    1. In parallel, so that it carries no current
    2. Across the earth wire, so that it never heats
    3. In parallel with each bulb, so the bulbs glow brighter
    4. In series, so that the whole current passes through it and it melts if the current is too large
    Show answer

    Answer: D. The fuse must carry the same current as the circuit it protects, so it is in series. When the current exceeds its limit, the fuse wire heats up, melts and breaks the circuit.

  4. 4. Your friend is stuck to a live wire and getting a shock. What should you do first?

    1. Pull your friend away with your bare hands
    2. Switch off the main switch, or push your friend away with a dry wooden pole
    3. Pour water on your friend
    4. Touch the wire to check whether it is live
    Show answer

    Answer: B. Touching the person would pass the current into you as well, and water conducts. Cut the supply at the main switch or plug, or use a dry wooden pole, which is an insulator, to push the person away.

  5. 5. On a 220 V supply, an iron of resistance 55 Ω and a fan of resistance 440 Ω are working together. What is the total current drawn?

    1. 4.5 A
    2. 4 A
    3. 0.44 A
    4. 0.5 A
    Show answer

    Answer: A. Both are in parallel across 220 V. Iron: 220 ÷ 55 = 4 A. Fan: 220 ÷ 440 = 0.5 A. Total = 4 + 0.5 = 4.5 A.

Privacy · Terms · Refunds · Delivery