• Practice
  • About 16 min
  • 5 practice questions

Electric circuits and Ohm's law

Draw and read circuit diagrams with standard symbols, connect an ammeter and a voltmeter correctly, state Ohm's law, and use V = IR to find current, potential difference or resistance.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Recognise the standard symbols used in circuit diagrams.
  • Explain why an ammeter goes in series and a voltmeter in parallel.
  • State Ohm's law and the condition under which it holds.
  • Use V = IR and define one ohm.
  • Describe how Ohm's law is checked by experiment and what the V-I graph looks like.

A bulb glows only when there is a complete conducting path from one terminal of the cell, through the bulb, back to the other terminal. Electricians and engineers plan such paths with diagrams that everyone can read. Once a circuit is built, Ohm's law tells us how much current will flow in it.

Electric circuits and circuit diagrams

A continuous path for electric current, through conducting wires joined to the two ends of a cell and to other components, is called an electric circuit. A drawing of it using standard symbols is a circuit diagram. If the path is broken anywhere, for example by an open key, a loose wire or a burnt filament, no current flows.

ComponentUse in the circuit
Electric cellProvides a potential difference (long line +, short line −)
BatterySeveral cells together, for a larger potential difference
Plug key or switch (open / closed)Breaks or completes the circuit
Connecting wireJoins components
BulbShows whether current is flowing
ResistorControls the current
Variable resistor (rheostat)Changes the resistance, and so the current
AmmeterMeasures current; connected in series
VoltmeterMeasures potential difference; connected in parallel

An ammeter must carry the whole current it measures, so it is placed in series, in the same path. A voltmeter compares the potential at two points, so it is connected in parallel across the component. A voltmeter has a very high resistance, so only a very small current passes through it and the circuit is hardly disturbed.

Ohm's law

The German scientist Georg Simon Ohm found how the current through a wire depends on the potential difference across it.

Ohm's law: if the physical state of a conductor stays the same, the current I through it is directly proportional to the potential difference V across its ends. V = IR, where R is the resistance of the conductor.

The physical state means the conductor's length, area of cross-section, temperature and material. From I ∝ V we write I = kV; putting 1/k = R gives V = IR, which can also be written as I = V/R or R = V/I. The SI unit of resistance is the ohm (Ω): a conductor has a resistance of 1 Ω if a current of 1 A flows through it when a potential difference of 1 V is applied across its ends. So 1 Ω = 1 V/1 A.

Worked example 1: a heater coil

Question: A heater coil has a resistance of 40 Ω and is connected to a 220 V supply. What current flows through it?

Working: I = V/R = 220 V ÷ 40 Ω = 5.5 A.

Worked example 2: a torch bulb

Question: A torch bulb draws 0.2 A from a 3 V battery. Find the resistance of its filament. What current would flow if the potential difference were 4.5 V, assuming the resistance stays the same?

Working: R = V/I = 3 V ÷ 0.2 A = 15 Ω. With 4.5 V: I = 4.5 ÷ 15 = 0.3 A. The potential difference went up 1.5 times and so did the current, as Ohm's law predicts.

Checking Ohm's law by experiment

Connect a piece of nichrome wire, an ammeter, a plug key and one 1.5 V cell in series, with a voltmeter across the nichrome wire. Note the readings. Add cells one at a time, noting the ammeter and voltmeter readings each time, and work out V/I for each pair. Then draw a graph of current against potential difference.

Made-up sample readings for a nichrome wire
Cells usedPotential difference V (volt)Current I (ampere)V/I (ohm)
11.50.1015
23.00.2015
34.50.3015
46.00.4015

V/I stays constant, and the graph of I against V is a straight line passing through the origin. This shows I ∝ V, which is Ohm's law. Conductors that follow this are ohmic; some conductors do not follow Ohm's law and are called non-ohmic conductors.

Steps in verifying Ohm's law

  1. Build the series circuit Cell, key, ammeter and nichrome wire; voltmeter across the wire.
  2. Record V and I For one cell, then two, three and four cells.
  3. Calculate V/I It comes out the same each time.
  4. Plot I against V A straight line through the origin confirms I ∝ V.

Key takeaways: a circuit is a complete conducting path; ammeters go in series and voltmeters in parallel. Ohm's law says V = IR as long as the conductor's length, thickness, temperature and material do not change. One ohm is one volt per ampere.

Check your understanding

  1. 1. How is an ammeter connected in a circuit?

    1. In parallel with the resistor
    2. In series, so the whole current passes through it
    3. Across the cell only
    4. It is not connected; it is held near the wire
    Show answer

    Answer: B. An ammeter measures the current through a path, so all of that current must pass through it: it is connected in series. A voltmeter, which measures potential difference, is the one connected in parallel.

  2. 2. Ohm's law holds for a conductor only if

    1. its physical state, including temperature, stays the same
    2. the current is very large
    3. it is made of copper
    4. it is connected in parallel
    Show answer

    Answer: A. Ohm's law states that I is proportional to V provided the conductor's physical state (length, cross-section, temperature and material) remains unchanged. If, for example, it heats up a lot, its resistance changes.

  3. 3. When 12 V is applied across a resistor, a current of 0.3 A flows. What is its resistance?

    1. 3.6 Ω
    2. 0.025 Ω
    3. 40 Ω
    4. 400 Ω
    Show answer

    Answer: C. R = V/I = 12 V ÷ 0.3 A = 40 Ω. Multiplying V by I gives 3.6, which is not a resistance.

  4. 4. For a conductor that obeys Ohm's law, the graph of current against potential difference is

    1. a curve that flattens out
    2. a horizontal line
    3. a vertical line
    4. a straight line passing through the origin
    Show answer

    Answer: D. Since I ∝ V, doubling V doubles I, and when V = 0 there is no current. That gives a straight line through the origin, whose slope is 1/R.

  5. 5. Which statement defines one ohm?

    1. The resistance through which 1 C passes in 1 s
    2. The resistance of a conductor that carries 1 A when 1 V is applied across it
    3. The resistance of 1 m of copper wire
    4. The resistance that uses 1 J of energy
    Show answer

    Answer: B. From R = V/I, 1 Ω = 1 V ÷ 1 A: a conductor has a resistance of one ohm if a potential difference of one volt across it drives a current of one ampere.

Privacy · Terms · Refunds · Delivery