Revision notes

Electricity: Foundation

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Electric charge and current

I = Q ÷ t. 1 A = 1 C/s. Ammeter in series. Conventional current: positive to negative.

— Remember
  • Charge is measured in coulombs; current in amperes (C/s).
  • Current needs a closed circuit.
  • An ammeter goes in series.
Read the full lesson

Lesson 2

Potential difference and Ohm's law

V = IR. R = ρL/A. Voltmeter in parallel, ammeter in series.

— Remember
  • V = IR; unit of R is the ohm.
  • Resistance rises with length and falls with area.
  • A voltmeter is connected in parallel.
Read the full lesson

Lesson 3

Resistors in series and parallel

Series: R = R₁ + R₂, same current. Parallel: 1/R = 1/R₁ + 1/R₂, same voltage.

— Remember
  • Series: same current, resistances add.
  • Parallel: same voltage, reciprocals add; total is less than the smallest.
  • Homes use parallel wiring.
Read the full lesson

Lesson 4

Electric power and energy

P = VI = I²R = V²/R. Energy (kWh) = kW × hours. 1 kWh = 3.6 × 10⁶ J.

— Formulas
  • P = VI = I²R = V²/R.
  • kWh = kW × hours; it is a unit of energy.
  • Bill = units × rate.
Read the full lesson

Lesson 5

Heating effect of current and electrical safety

H = I²Rt. A fuse melts to protect the circuit; earthing protects the user.

— Remember
  • Heat H = I²Rt.
  • A fuse is placed in series and breaks the circuit when the current is too high.
  • Earthing and MCBs make homes safer.
Read the full lesson

Lesson 6

Static electricity: charging objects and the electroscope

Charging is the transfer of electrons. Gain electrons: negative. Lose electrons: positive. Like repel, unlike attract. Charge is conserved.

— Rule to remember
  • Only electrons move; gaining them makes an object negative.
  • Charging by friction, contact and induction.
  • Earthing and lightning conductors lead charge safely to the ground.
  • An electroscope shows the presence of charge by spreading leaves.
Read the full lesson

Lesson 7

Cells, batteries and circuit diagrams

Common components
ComponentJobSymbol idea
CellSource of energyLong line (positive) and short line (negative)
BatterySeveral cellsPair or more of such lines
SwitchOpens or closes the circuitGap that can be closed
BulbGives lightCircle with a cross
ResistorOpposes currentRectangle
AmmeterMeasures currentCircle with A
VoltmeterMeasures potential differenceCircle with V

Series: voltages add. Parallel: voltage stays the same and the set lasts longer. A circuit works only when it is a complete loop.

— Rule to remember
  • A battery is a group of cells.
  • Series raises the voltage; parallel raises the lifetime.
  • Circuits need a complete path.
  • A short circuit gives a dangerously large current.
Read the full lesson

Lesson 8

Meters and V-I graphs: reading Ohm's law from data

A set of readings for a resistor
V (volt)I (ampere)V / I (Ω)
20.54
41.04
61.54
82.04

R = V / I. On a V-I graph (V vertical), the slope is the resistance. A straight line through the origin means ohmic. Check the axes and the zero error.

— Rule to remember
  • Ammeter in series, voltmeter in parallel.
  • Least count = range / divisions; correct for zero error.
  • Slope of a V-I line is the resistance.
  • A curved line means a non-ohmic conductor.
Read the full lesson

Lesson 9

Household electricity: live, neutral, earth and AC versus DC

Wires in a house
WireJob
LiveCarries current to the appliance; at a high potential, so it is the dangerous wire
NeutralCarries current back to the supply; near zero potential
EarthSafety wire joined to the ground; carries no current normally

Fuse and switch on the live wire. The earth wire carries a fault current to the ground. Household appliances are in parallel. Current = power / voltage.

— Rule to remember
  • Live, neutral and earth wires have different jobs.
  • Switches and fuses are placed in the live wire.
  • AC reverses direction; DC flows one way.
  • Check the total current against the fuse rating.
Read the full lesson

Privacy · Terms · Refunds · Delivery