• Foundation
  • About 14 min
  • 5 practice questions

Meters and V-I graphs: reading Ohm's law from data

Read ammeter and voltmeter scales, find resistance from a table or graph of readings, and tell ohmic from non-ohmic conductors.

If something looks wrong, please tell us.

Ohm's law says that the current through a conductor is proportional to the potential difference across it. We test the law by changing the voltage, noting the current, and looking for a pattern. In this lesson you will learn to read meters, to turn a table of readings into a resistance, and to read a V-I graph. All readings are illustrative.

Using the meters

  • An ammeter is connected in series and has very low resistance, so that it does not change the current.
  • A voltmeter is connected in parallel across the part being tested and has very high resistance, so that it takes almost no current.
  • Before reading, check the zero error: if the pointer is not at zero when the circuit is off, subtract (or add) the error from every reading.
  • Find the least count, the value of the smallest division on the scale: least count = range / number of divisions.

From data to resistance

By Ohm's law, V = IR, so R = V / I. If V is plotted on the vertical axis and I on the horizontal axis, the graph is a straight line through the origin, and the slope of the line is the resistance. A conductor that gives a straight line is called ohmic. Some conductors do not follow Ohm's law. The filament of a bulb, for example, gets hotter as the current rises and its resistance increases, so its graph curves. Such a conductor is non-ohmic.

A set of readings for a resistor
V (volt)I (ampere)V / I (Ω)
20.54
41.04
61.54
82.04

Worked example 1: constant ratio

The table shows V / I = 4 Ω for every pair. A constant ratio means that V is proportional to I, so this conductor obeys Ohm's law. Its resistance is 4 Ω. If the readings were 2 V with 0.5 A, 4 V with 0.8 A and 6 V with 1.0 A, the ratios would be 4, 5 and 6 Ω and the resistance would be rising, so the conductor would be non-ohmic.

Worked example 2: slope of a graph

On a V-I graph, two points on the straight line are (I = 0.5 A, V = 3 V) and (I = 1.5 A, V = 9 V). Slope = change in V / change in I = (9 - 3) / (1.5 - 0.5) = 6 / 1 = 6 Ω. Check with one point: 3 / 0.5 = 6 Ω. Using the slope is better than using a single point because it uses all the data and removes any zero error.

Worked example 3: least count

An ammeter scale runs from 0 to 5 A with 50 divisions. Least count = 5 / 50 = 0.1 A per division. A pointer standing at 23 divisions reads 23 × 0.1 = 2.3 A. If the meter has a zero error of +0.1 A (the pointer rests at 0.1 A when no current flows), the true reading is 2.3 - 0.1 = 2.2 A.

Worked example 4: which is steeper?

Two resistors have V-I lines. Resistor X has R = 10 Ω and resistor Y has R = 5 Ω. When V is on the vertical axis, a larger R means a steeper line, so X is the steeper line. If current were plotted on the vertical axis instead, the larger resistance would give the flatter line. Always check which quantity is on which axis.

R = V / I. On a V-I graph (V vertical), the slope is the resistance. A straight line through the origin means ohmic. Check the axes and the zero error.

— Rule to remember

Key takeaways

  • Ammeter in series, voltmeter in parallel.
  • Least count = range / divisions; correct for zero error.
  • Slope of a V-I line is the resistance.
  • A curved line means a non-ohmic conductor.

Check your understanding

  1. 1. A voltmeter is connected:

    1. In series with the part
    2. In parallel with the part
    3. Only across the cell
    4. Only on a switch
    Show answer

    Answer: B. A voltmeter measures the potential difference across a component, so it goes in parallel with it.

  2. 2. A resistor carries 0.4 A when the voltage across it is 2 V. Its resistance is:

    1. 5 Ω
    2. 0.8 Ω
    3. 1.25 Ω
    4. 8 Ω
    Show answer

    Answer: A. R = 2 / 0.4 = 5 Ω.

  3. 3. A voltmeter scale of 0 to 10 V has 100 divisions. The least count is:

    1. 1 V
    2. 0.01 V
    3. 10 V
    4. 0.1 V
    Show answer

    Answer: D. 10 / 100 = 0.1 V per division.

  4. 4. Which graph shows an ohmic conductor?

    1. A curve that bends upward
    2. A curve that bends downward
    3. A straight line through the origin
    4. A horizontal line from the origin
    Show answer

    Answer: C. An ohmic conductor gives a straight line through the origin on a V-I graph.

  5. 5. On a V-I graph, points (1 A, 4 V) and (3 A, 12 V) lie on a line. The resistance is:

    1. 4 Ω
    2. 12 Ω
    3. 2 Ω
    4. 8 Ω
    Show answer

    Answer: A. Slope = (12 - 4) / (3 - 1) = 8 / 2 = 4 Ω.

Privacy · Terms · Refunds · Delivery