- Foundation
- About 13 min
- 5 practice questions
Household electricity: live, neutral, earth and AC versus DC
Describe the wires in a house, the work of the switch, fuse and earth wire, the difference between AC and DC, and simple limits on the load of a circuit.
If something looks wrong, please tell us.
The electricity in your home does not come from a cell. It comes through a pair of wires from the supply network, with a third wire for safety. In this lesson you will learn the names and roles of these wires, how alternating current differs from the direct current of a cell, and how to check that a circuit is not overloaded. For practice, the supply is taken as 220 V.
The three wires
| Wire | Job |
|---|---|
| Live | Carries current to the appliance; at a high potential, so it is the dangerous wire |
| Neutral | Carries current back to the supply; near zero potential |
| Earth | Safety wire joined to the ground; carries no current normally |
A three-pin plug has pins for the live, neutral and earth wires. The earth pin is usually longer and thicker. It is connected to the metal body of an appliance such as an iron or a refrigerator. If a fault makes the live wire touch the metal body, the current flows through the earth wire into the ground instead of through a person who touches the body. The big current also blows the fuse. The switch and the fuse are placed on the live wire, so that when the switch is off or the fuse has blown, the appliance is cut off from the high potential.
Alternating and direct current
A cell gives direct current (DC), in which the current flows in one direction only. The mains supply gives alternating current (AC), in which the current reverses its direction again and again. In India the supply reverses 100 times each second, which is a frequency of 50 hertz (50 complete cycles per second). AC is used for supply networks because its voltage can be changed easily with a transformer, which makes long-distance transmission efficient. Devices that need DC, such as phone chargers, contain a circuit that converts AC to DC.
Overloading and short circuits
Household appliances are connected in parallel across the supply, so each gets the full voltage and works independently. The currents add up. Overloading happens when too many appliances are used on one circuit and the total current exceeds the safe value of the wires. A short circuit occurs when live and neutral touch directly, so the resistance is very low and the current is huge. A fuse or an MCB cuts off the circuit in either case.
Worked example 1: current of an appliance
A geyser is rated 2,200 W at 220 V. Current = P / V = 2,200 / 220 = 10 A. A fuse rated 5 A would blow at once, so a fuse rated a little above 10 A, such as 15 A, is suitable.
Worked example 2: is the circuit overloaded?
A circuit has a fuse of 5 A. Appliances: a fan of 80 W, a lamp of 40 W and a television of 100 W. Total power = 80 + 40 + 100 = 220 W. Total current = 220 / 220 = 1 A, well below 5 A, so the circuit is safe. Maximum safe power on this circuit = 220 × 5 = 1,100 W. A 1,500 W heater added to the circuit would take it to 1,720 W and the fuse would blow.
Worked example 3: AC cycles
The frequency is 50 Hz. In 3 seconds the number of cycles = 50 × 3 = 150. Each cycle has two reversals of direction, so the number of reversals = 150 × 2 = 300.
Fuse and switch on the live wire. The earth wire carries a fault current to the ground. Household appliances are in parallel. Current = power / voltage.
Key takeaways
- Live, neutral and earth wires have different jobs.
- Switches and fuses are placed in the live wire.
- AC reverses direction; DC flows one way.
- Check the total current against the fuse rating.
Check your understanding
-
1. The fuse and the switch are placed in the:
- Neutral wire
- Earth wire
- Any wire
- Live wire
Show answer
Answer: D. They are in the live wire so that the appliance is cut off from the high potential when the fuse blows or the switch is off.
-
2. The purpose of the earth wire is to:
- Increase the supply voltage
- Take fault current to the ground
- Carry the current all the time
- Make all appliances run faster
Show answer
Answer: B. If a fault puts the live wire in contact with the metal body, the earth wire carries the current to the ground.
-
3. An appliance of 1,100 W runs at 220 V. The current is:
- 2 A
- 10 A
- 5 A
- 0.5 A
Show answer
Answer: C. I = P / V = 1,100 / 220 = 5 A.
-
4. Alternating current is current that:
- Flows in one direction only
- Never changes in size
- Is produced only by cells
- Reverses its direction repeatedly
Show answer
Answer: D. AC reverses direction again and again, while DC flows one way.
-
5. Why are household appliances connected in parallel?
- Each gets the full voltage
- They use much less power
- The wires are much shorter
- They can never overload
Show answer
Answer: A. In parallel, each appliance has the full supply voltage and can be switched on or off without affecting the others.
Sign in to keep track of the lessons you finish.