Revision notes

Magnetism: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Magnets, field lines and magnetic dipoles

τ = MB sin θ. U = −MB cos θ. Magnetic poles never exist alone. Field lines are closed loops.

— Remember
  • Monopoles do not exist; field lines are closed loops.
  • Torque is greatest at 90° and zero when aligned.
  • A current loop acts as a magnetic dipole with M = NIA.
Read the full lesson

Lesson 2

Magnetic field due to current

Straight wire: B = μ₀I/2πr. Loop centre: B = μ₀NI/2R. Solenoid: B = μ₀nI. μ₀ = 4π × 10⁻⁷ T m/A.

— Remember
  • Field from a wire falls as 1/r; inside a solenoid it is uniform.
  • Count turns per unit length n for a solenoid.
  • Use the right-hand rule for direction.
Read the full lesson

Lesson 3

Force on a moving charge and on a current

F = qvB sin θ. F = BIL sin θ. r = mv/qB. Parallel currents attract; antiparallel currents repel. A magnetic force does no work on a charge.

— Remember
  • Magnetic force is perpendicular to both v and B.
  • The radius of a charge's circular path is proportional to its speed.
  • Parallel currents attract.
Read the full lesson

Lesson 4

Electromagnetic induction

ε = −N ΔΦ/Δt. Motional emf = BLv. Lenz's law: induced effects oppose the cause. ε = −L ΔI/Δt.

— Remember
  • Induced emf depends on the rate of change of flux, not on the flux itself.
  • Lenz's law gives the direction: the effect opposes its cause.
  • More turns give a proportionally larger emf.
Read the full lesson

Lesson 5

Transformers, generators and applications

V_s/V_p = N_s/N_p. Ideal: V_pI_p = V_sI_s. Step-up raises voltage and lowers current. Transformers need AC.

— Remember
  • Step-up: more secondary turns, less secondary current.
  • High-voltage transmission reduces I²R loss.
  • A generator converts mechanical to electrical energy; a motor does the reverse.
Read the full lesson

Lesson 6

Combining fields: null points, perpendicular contributions and arcs

Add fields as vectors. Null point: I₁/r₁ = I₂/r₂. Arc: B = μ₀Iθ/(4πR). A wire pointing at the point gives zero field there.

— Rules to remember

Break each problem into single-conductor fields, give each a direction, and add as vectors. The null point condition is just I₁/r₁ = I₂/r₂, with the positions chosen to suit the directions.

Read the full lesson

Lesson 7

Charged particles in magnetic fields: ratios and quick-solution methods

Radius ratios in the same field
Particles enter with the sameThe radius is proportional to
speedm/q
momentum1/q
kinetic energy√m / q
accelerating voltage√(m/q)

r = mv/qB; T = 2πm/qB. Same v: r ∝ m/q. Same K: r ∝ √m/q. Same V: r ∝ √(m/q). T does not depend on speed.

— Ratios to remember

Write the formula for r, decide which quantities are common to the particles, cancel them and read off the ratio. The period depends only on m/q and B.

Read the full lesson

Lesson 8

Induction numericals: charge, rotating rods, sliding rods and coils

q = NΔΦ/R. Rotating rod: ½Bωl². Sliding rod: ε = Blv, F = B²l²v/R. Rotating coil: peak = NBAω.

— Patterns to remember

Identify the pattern and write the shortcut formula. In every case, check energy conservation if you can: the mechanical power supplied equals the electrical power dissipated.

Read the full lesson

Lesson 9

Inductance, AC and transformers: a mixed numerical set

ε = L ΔI/Δt; U = ½LI². V_rms = V₀/√2. Efficiency = P_out/P_in. Line loss = (P/V)²R.

— Formulae to remember

Identify which of the five formulae the problem needs, substitute with units, and check the answer for sense: stored energy in joules, line loss less than the power sent, efficiency less than 100%.

Read the full lesson

Privacy · Terms · Refunds · Delivery