Revision notes

Properties of Matter: Foundation

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

States of matter and intermolecular forces

The three states
PropertySolidLiquidGas
ShapeFixedTakes the shape of containerTakes the shape of container
VolumeFixedFixedFills the container
Particle spacingVery closeCloseFar apart
Intermolecular forceStrongestMediumVery weak
CompressibilityAlmost noneVery littleHigh

Solid: fixed shape and volume. Liquid: fixed volume, no fixed shape. Gas: neither.

— Remember
  • State depends on particle spacing and intermolecular forces.
  • Cohesion is like-to-like; adhesion is between different substances.
  • Solids are strongest bound; gases weakest.
Read the full lesson

Lesson 2

Density and relative density

ρ = m ÷ V. Relative density = ρ(substance) ÷ ρ(water), no unit. 1 g/cm³ = 1000 kg/m³.

— Formulas
  • Density is mass per unit volume.
  • Relative density has no unit.
  • Less than 1 floats in water; more than 1 sinks.
Read the full lesson

Lesson 3

Elasticity, stress and strain

Stress = F ÷ A. Strain = ΔL ÷ L (no unit). Within the elastic limit, stress ∝ strain. Spring: F = kx.

— Hooke's law
  • Stress = force per unit area; strain = fractional change in length.
  • Hooke's law holds within the elastic limit.
  • Young's modulus = stress ÷ strain.
Read the full lesson

Lesson 4

Surface tension and viscosity

Surface tension makes liquid surfaces behave like stretched skin (unit N/m). Viscosity is the internal friction of fluids.

— Remember
  • Surface tension acts like a skin and shapes drops; heat and soap lower it.
  • Capillary rise happens when adhesion beats cohesion.
  • Viscosity is internal friction in a fluid and falls as liquids are heated.
Read the full lesson

Lesson 5

Properties of matter: mixed practice

Check units first: convert everything to SI before using the formula.

— Exam tip
  • Density of a mixture = total mass ÷ total volume, not the average of the densities.
  • Convert to SI units before calculating.
  • Use F = mg for loads and the radius for areas.
Read the full lesson

Lesson 6

Wetting, the meniscus and capillary rise

Wetting and non-wetting
Liquid and solidWhich force winsWhat you see
Water on clean glassAdhesionWater spreads and wets the glass
Mercury on glassCohesionMercury forms round beads
Water on a waxed or oily surfaceCohesionWater forms drops and rolls off
Water on cotton clothAdhesionCloth soaks up water

Adhesion greater than cohesion: the liquid wets and rises in a capillary. Cohesion greater: it does not wet and is pushed down. Rise is inversely proportional to the radius.

— Rule to remember
  • Wetting depends on adhesion versus cohesion.
  • A wetting liquid has a concave meniscus and an angle of contact below 90°.
  • Narrower capillary: greater rise; h × r is constant for a given liquid and tube material.
  • Wicks, blotting paper, soil and plant stems all use capillary action.
Read the full lesson

Lesson 7

Density in more depth: mixtures, alloys and the density bottle

Density of a mixture = total mass ÷ total volume. Equal volumes: simple average. An object floats if its average density is less than the liquid's.

— Rule to remember
  • Add the masses and add the volumes, then divide.
  • The mixture density is not the average unless the volumes are equal.
  • The density bottle uses water to find the bottle's volume.
  • Average density, including any hollow space, decides floating.
Read the full lesson

Lesson 8

Bulk modulus, shear modulus and safe loads

Kinds of strain and modulus
KindWhat happensStrain isModulus
LongitudinalLength changesΔL ÷ LYoung's modulus Y
VolumeVolume changes under pressure on all sidesΔV ÷ VBulk modulus K
ShearLayers slide, shape changes but not volumeAngle θ in radian (= x ÷ h)Shear modulus G

K = ΔP ÷ (ΔV ÷ V). G = (F ÷ A) ÷ θ. Safe stress = breaking stress ÷ factor of safety. Only solids have a shear modulus.

— Rule to remember
  • Three strains: change of length, of volume and of shape.
  • Bulk modulus links pressure to fractional volume change; high K means hard to compress.
  • Shear modulus uses the angle, a pure number in radian.
  • Choose a working load well below the breaking load.
Read the full lesson

Lesson 9

Fluids in motion: streamline flow, continuity and terminal velocity

Continuity: A₁v₁ = A₂v₂ (narrower means faster). At terminal velocity weight = buoyancy + drag, so the net force is zero.

— Rule to remember
  • Streamline flow is smooth and steady; turbulent flow is swirling.
  • Volume per second Q = A × v is the same all along a pipe.
  • Viscosity is internal friction; it drops when a liquid is heated.
  • Terminal velocity increases with the square of the ball's radius.
Read the full lesson

Privacy · Terms · Refunds · Delivery