• Foundation
  • About 14 min
  • 5 practice questions

Bulk modulus, shear modulus and safe loads

Meet the three kinds of strain and their moduli, use gentle numerical examples, and understand breaking stress and the factor of safety.

If something looks wrong, please tell us.

So far we have stretched wires. But solids can also be squeezed on all sides, like a stone deep in the sea, or sheared, like a book pushed sideways on a table. Each kind of deformation has its own strain and its own modulus. This lesson explains them in simple steps and then shows how engineers choose safe loads.

Three kinds of strain

Kinds of strain and modulus
KindWhat happensStrain isModulus
LongitudinalLength changesΔL ÷ LYoung's modulus Y
VolumeVolume changes under pressure on all sidesΔV ÷ VBulk modulus K
ShearLayers slide, shape changes but not volumeAngle θ in radian (= x ÷ h)Shear modulus G

The formulas

  • Bulk modulus: K = pressure increase ÷ fractional decrease in volume = ΔP ÷ (ΔV ÷ V), taking the size of the decrease. The reciprocal 1/K is called compressibility.
  • Shear modulus: G = shear stress ÷ shear strain = (F ÷ A) ÷ θ. Here F acts along the face of area A, and θ = x ÷ h is how far the top moves sideways (x) divided by the height (h).
  • Liquids and gases can be compressed, so they have a bulk modulus. They cannot keep their shape under a sideways force, so only solids have a shear modulus.

Breaking stress and the factor of safety

Elastic limit: the stress beyond which a wire will not return to its original length. Breaking stress: the stress at which the material fails. Engineers never load a cable up to its breaking stress. They divide by a factor of safety: safe working stress = breaking stress ÷ factor of safety.

Worked examples

Example 1: bulk modulus. A liquid has K = 2 × 10⁹ Pa. The pressure on it is raised by 2 × 10⁷ Pa. The fractional change in volume = 2 × 10⁷ ÷ 2 × 10⁹ = 0.01, which is a 1% decrease. If the volume was 500 cm³, the decrease is 0.01 × 500 = 5 cm³.

Example 2: compressibility. For the same liquid, compressibility = 1 ÷ K = 1 ÷ (2 × 10⁹) = 5 × 10⁻¹⁰ per pascal. The smaller this number, the harder the liquid is to compress.

Example 3: shear. A solid block of height 0.1 m has a top face of area 0.02 m². The top is pushed sideways by 0.5 mm, so θ = 0.0005 ÷ 0.1 = 5 × 10⁻³ radian. If G = 4 × 10⁹ Pa (an illustrative value), the shear stress = 4 × 10⁹ × 5 × 10⁻³ = 2 × 10⁷ Pa. The force needed = stress × area = 2 × 10⁷ × 0.02 = 4 × 10⁵ N.

Example 4: safe load. A steel cable has cross-section 10⁻⁴ m² and a breaking stress of 4 × 10⁸ Pa. It breaks at a load of 4 × 10⁸ × 10⁻⁴ = 4 × 10⁴ N. With a factor of safety of 4, the safe working stress = 10⁸ Pa and the safe load = 10⁸ × 10⁻⁴ = 10⁴ N. (These are illustrative figures, not data for any real cable.)

K = ΔP ÷ (ΔV ÷ V). G = (F ÷ A) ÷ θ. Safe stress = breaking stress ÷ factor of safety. Only solids have a shear modulus.

— Rule to remember

Key takeaways

  • Three strains: change of length, of volume and of shape.
  • Bulk modulus links pressure to fractional volume change; high K means hard to compress.
  • Shear modulus uses the angle, a pure number in radian.
  • Choose a working load well below the breaking load.

Check your understanding

  1. 1. A liquid has K = 4 × 10⁹ Pa. A pressure rise of 4 × 10⁷ Pa causes a fractional decrease in volume of:

    1. 0.1
    2. 0.001
    3. 0.01
    4. 0.0001
    Show answer

    Answer: C. ΔV ÷ V = ΔP ÷ K = 4 × 10⁷ ÷ 4 × 10⁹ = 0.01.

  2. 2. Which of these materials has NO shear modulus?

    1. Steel
    2. Copper
    3. Glass
    4. Water
    Show answer

    Answer: D. A liquid cannot keep its shape under a sideways force, so it has no shear modulus. Solids do.

  3. 3. The top face of a cube of side 0.1 m is pushed sideways by 0.2 mm. The shear strain is:

    1. 2 × 10⁻³ radian
    2. 2 × 10⁻⁴ radian
    3. 2 × 10⁻² radian
    4. 0.2 radian
    Show answer

    Answer: A. θ = x ÷ h = 0.0002 ÷ 0.1 = 2 × 10⁻³ radian.

  4. 4. A rod has a breaking stress of 6 × 10⁸ Pa. With a factor of safety of 3, the safe working stress is:

    1. 1.8 × 10⁹ Pa
    2. 2 × 10⁸ Pa
    3. 6 × 10⁸ Pa
    4. 3 × 10⁸ Pa
    Show answer

    Answer: B. Safe stress = breaking stress ÷ factor of safety = 6 × 10⁸ ÷ 3 = 2 × 10⁸ Pa.

  5. 5. A material with a large bulk modulus is:

    1. Easy to compress
    2. Impossible to stretch
    3. Hard to compress
    4. Always a gas
    Show answer

    Answer: C. Since K = ΔP ÷ (ΔV ÷ V), a large K means a large pressure is needed for a small fractional change in volume. The material is hard to compress.

Privacy · Terms · Refunds · Delivery