Revision notes

Units and Measurement: Practice

The key points, rules to remember, tables and diagrams from all 9 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

SI units, conversions and dimensions

Common dimensional formulae
QuantityFormulaDimensionsSI unit
Velocitydistance / time[L T⁻¹]m/s
Accelerationvelocity / time[L T⁻²]m/s²
Forcem × a[M L T⁻²]newton (N)
Work / energyF × d[M L² T⁻²]joule (J)
Powerwork / time[M L² T⁻³]watt (W)
Pressureforce / area[M L⁻¹ T⁻²]pascal (Pa)
Momentum / impulsem × v[M L T⁻¹]kg m/s

Dimensions of a derived quantity = replace each symbol in its defining equation by its dimensions. Numbers and angles have no dimensions. 1 kWh = 3.6 × 10⁶ J.

— Remember
  • Learn the seven SI base units; all others are combinations of them.
  • Convert km/h to m/s by multiplying by 5/18, and m/s to km/h by 18/5.
  • Get dimensions from the defining equation; keep the units consistent while converting.
  • Pressure, energy and power dimensions appear again and again, so memorise them.
Read the full lesson

Lesson 2

Dimensional analysis and its uses

A dimensionally correct equation need not be physically correct, but a dimensionally wrong equation is certainly wrong.

— Rule to remember
  • Compare dimensions on both sides term by term.
  • To derive, equate powers of M, L and T on both sides.
  • The method misses numerical constants and cannot choose between equations with equal dimensions.
Read the full lesson

Lesson 3

Significant figures and rounding

Add or subtract: match decimal places. Multiply or divide: match significant figures. Unit conversion does not change the number of significant figures.

— Rule to remember
  • Leading zeros never count; trailing zeros after a decimal point do.
  • Decimal places rule for sums, significant figures rule for products.
  • Carry extra digits in the middle of a calculation and round only the final answer.
Read the full lesson

Lesson 4

Errors in measurement

Rules for combining errors
OperationResultError rule
Sum or differenceZ = A ± BΔZ = ΔA + ΔB (absolute errors add)
Product or quotientZ = A × B or A / BΔZ/Z = ΔA/A + ΔB/B (relative errors add)
PowerZ = A^nΔZ/Z = n × ΔA/A

Sum or difference: add absolute errors. Product or quotient: add percentage errors. A power n multiplies the percentage error by n.

— Remember
  • Percentage error = (mean absolute error / mean) × 100.
  • Errors in differences add too; they never cancel.
  • A power in the formula multiplies the percentage error by that power.
Read the full lesson

Lesson 5

Vernier calipers and screw gauge

Least count (screw gauge) = pitch / circular divisions. Corrected reading = observed reading − zero error (with its sign).

— Remember
  • Least count decides the precision of an instrument.
  • Always check the zero error first and apply its sign correctly.
  • A smaller least count gives a smaller percentage error in the same measurement.
Read the full lesson

Lesson 6

Unit conversion problem set: speed, density, area and pressure

Factors to memorise
ConversionFactor
km/h to m/smultiply by 5/18 (divide by 3.6)
m/s to km/hmultiply by 18/5 (multiply by 3.6)
m² to cm²1 m² = 10⁴ cm²
m³ to cm³1 m³ = 10⁶ cm³
litre1 L = 1000 cm³ = 10⁻³ m³
density1 g/cm³ = 1000 kg/m³
pressure1 Pa = 10 dyne/cm²

A quantity with unit u^n needs the conversion factor raised to the power n. Bigger unit, smaller number.

— Rule to remember
  • Memorise the factors in the table; they cover most exam questions.
  • Raise the factor to the power in the unit: cm² needs a squared factor, cm³ a cubed one.
  • Always check whether the new number should be larger or smaller than the old one.
Read the full lesson

Lesson 7

Dimensional formulae problem set: finding dimensions quickly

Building blocks to memorise
QuantityDimensions
Velocity[L T⁻¹]
Acceleration[L T⁻²]
Force[M L T⁻²]
Energy, work, torque[M L² T⁻²]
Momentum, impulse[M L T⁻¹]
Pressure, stress, energy per unit volume[M L⁻¹ T⁻²]
Power[M L² T⁻³]

Pick the nearest definition, substitute dimensions, and count powers of M, L and T separately.

— Rule to remember
  • Reuse building blocks (force, energy, pressure) to shorten every derivation.
  • Per unit length divides by [L], per unit area by [L²], per unit mass by [M].
  • Numbers and angles do not change the dimensions.
Read the full lesson

Lesson 8

Spot the correct equation: checking and deriving by dimensions

Only quantities of the same dimensions may be added or equated. To derive: equate the powers of M, L and T on both sides.

— Rule to remember
  • To choose the right formula, check each option term by term.
  • To derive a relation, set up one equation per base quantity.
  • Dimensional analysis never gives pure numbers such as ½ or 2π.
Read the full lesson

Lesson 9

Errors and significant figures together: a mixed exam set

Worst-case error: add absolute errors for + and −, add percentage errors for × and ÷. Round the final answer to the least precise input.

— Rule to remember
  • Use percentage errors for products, quotients and powers; absolute errors for sums and differences.
  • Timing n oscillations divides the error in one period by n.
  • The final answer should match the precision of the least precise measurement.
Read the full lesson

Privacy · Terms · Refunds · Delivery