• Practice
  • About 15 min
  • 5 practice questions

Errors and significant figures together: a mixed exam set

Combine error propagation, least count and significant figures in single questions, including timing many oscillations to reduce error.

If something looks wrong, please tell us.

Examiners often combine ideas. A question may give readings with their errors, ask for a calculated result and its error, and then ask how the answer should be written. This lesson brings together the error rules and the significant-figure rules in one place, with the reasoning for each step.

Rules to keep ready

  • Sum or difference: absolute errors add.
  • Product or quotient: percentage errors add.
  • Power: multiply the percentage error by the power. A square root counts half.
  • Numbers such as ½, 2 and π carry no error.
  • Multiplication and division: the answer has as many significant figures as the least precise factor. Addition and subtraction: as many decimal places as the least precise term.
  • A single reading with a stated least count has an error equal to the least count.

Worked examples

Example 1. A block has mass (25.0 ± 0.1) g and volume (10.0 ± 0.2) cm³. Find its density with the error. Density = 25.0 ÷ 10.0 = 2.50 g/cm³. Percentage error in mass = 0.1/25.0 × 100 = 0.4%. Percentage error in volume = 0.2/10.0 × 100 = 2%. Total = 2.4%. Absolute error = 2.4% of 2.50 = 0.06. So density = (2.50 ± 0.06) g/cm³.

Example 2. A rectangle measures 5.2 cm by 3.1 cm with a ruler of least count 0.1 cm. Area = 5.2 × 3.1 = 16.12 cm², which has two significant figures, so 16 cm². Percentage errors: 0.1/5.2 = 1.9% and 0.1/3.1 = 3.2%, total 5.1%. The absolute error = 5.1% of 16.12 ≈ 0.8 cm². The result is reported as (16 ± 1) cm².

Example 3 (timing many oscillations). A stopwatch has least count 0.1 s. The time for 20 oscillations of a pendulum is 36.4 s, so T = 36.4 ÷ 20 = 1.82 s. The error in T is 0.1 ÷ 20 = 0.005 s, which is 0.005/1.82 = 0.27%. If a single oscillation had been timed, the error would be 0.1 s, which is 0.1/1.82 = 5.5%. Timing many oscillations makes the percentage error 20 times smaller.

Example 4. For z = a² b / √c the percentage errors in a, b and c are 1%, 2% and 4%. Error in z = 2(1) + 1(2) + ½(4) = 2 + 2 + 2 = 6%.

Example 5. Add 12.5, 3.75 and 0.125. The raw sum is 16.375. The least precise term, 12.5, has one decimal place, so the answer is 16.4.

Example 6. Two lengths are (20.5 ± 0.1) cm and (12.3 ± 0.1) cm. The difference is 8.2 cm and the absolute error is 0.1 + 0.1 = 0.2 cm. The percentage error is 0.2/8.2 × 100 = 2.4%, much larger than in either length (0.5% and 0.8%). Subtracting nearly equal numbers makes the relative error worse.

Traps

  • Subtracting errors in a difference. Errors always add in the worst case.
  • Forgetting that a squared factor doubles its percentage error.
  • Rounding in the middle of the calculation. Keep an extra digit and round at the end.
  • Quoting the answer to more figures than the data support.

Worst-case error: add absolute errors for + and −, add percentage errors for × and ÷. Round the final answer to the least precise input.

— Rule to remember

Key takeaways

  • Use percentage errors for products, quotients and powers; absolute errors for sums and differences.
  • Timing n oscillations divides the error in one period by n.
  • The final answer should match the precision of the least precise measurement.

Check your understanding

  1. 1. For Z = A³/B the percentage errors in A and B are 2% and 3%. The maximum percentage error in Z is:

    1. 5%
    2. 6%
    3. 9%
    4. 18%
    Show answer

    Answer: C. Error = 3 × 2% + 3% = 6% + 3% = 9%.

  2. 2. Multiply 4.50 by 3.2 and give the answer with the correct number of significant figures.

    1. 14.4
    2. 14
    3. 14.40
    4. 15
    Show answer

    Answer: B. 4.50 × 3.2 = 14.4. The factor 3.2 has two significant figures, so the answer is 14.

  3. 3. Two lengths 20.5 ± 0.1 cm and 12.3 ± 0.1 cm are subtracted. The result with its error is:

    1. 8.2 ± 0.2 cm
    2. 8.2 ± 0.1 cm
    3. 8.2 ± 0.0 cm
    4. 8.2 ± 0.02 cm
    Show answer

    Answer: A. The difference is 8.2 cm. In a difference the absolute errors add: 0.1 + 0.1 = 0.2 cm.

  4. 4. In g = 4π² L/T², L has a 0.5% error and T has a 0.5% error. The percentage error in g is:

    1. 0.5%
    2. 1.0%
    3. 2.0%
    4. 1.5%
    Show answer

    Answer: D. Error = 0.5% + 2 × 0.5% = 1.5%. The factor 4π² carries no error.

  5. 5. The time for 10 oscillations is 15.0 s, measured with a stopwatch of least count 0.1 s. The absolute error in the time period is:

    1. 0.1 s
    2. 0.01 s
    3. 1.5 s
    4. 0.001 s
    Show answer

    Answer: B. The error in the total time is 0.1 s. The period is T = total ÷ 10, so its error is 0.1 ÷ 10 = 0.01 s.

Privacy · Terms · Refunds · Delivery