Revision notes

Unit 4 Electricity: Foundation

The key points, rules to remember, tables and diagrams from all 5 lessons, on one page for quick revision. To keep a copy, use your browser's Print and choose "Save as PDF".

Lesson 1

Electric current, circuits and potential difference

Some circuit components and their uses
ComponentUse
ResistorFixes the size of the current in a circuit
Variable resistor (rheostat)Lets you select (vary) the current
AmmeterMeasures current
VoltmeterMeasures potential difference
GalvanometerDetects a current and its direction
DiodeUsed in electronic devices
Light emitting diode (LED)Used, for example, in seven segment displays
Ground (earth) connectionProtects components; a reference point for measuring potential

Two directions in one circuit

  • Electron flow
    • From negative terminal
    • Through the circuit
    • To positive terminal
  • Conventional current
    • From positive terminal (higher potential)
    • Through the circuit
    • To negative terminal (lower potential)

I = Q/t (1 A = 1 C s⁻¹). V = W/Q (1 V = 1 J C⁻¹). Conventional current flows from + to − outside the cell, opposite to the electrons.

Key takeaways: current is charge per second; potential difference is energy per unit charge. A circuit must be closed for current to flow, and the battery provides the potential difference that drives it.

Read the full lesson

Lesson 2

Ohm's law, resistance, resistivity and conductivity

Resistivity of some materials (values as given in the Tamil Nadu textbook)
NatureMaterialResistivity (Ω m)
ConductorCopper1.62 × 10⁻⁸
ConductorNickel6.84 × 10⁻⁸
ConductorChromium12.9 × 10⁻⁸
InsulatorGlass10¹⁰ to 10¹⁴
InsulatorRubber10¹³ to 10¹⁶

What decides a wire's resistance (R = ρL/A)

  • Length L
    • Longer wire: more resistance
  • Area of cross-section A
    • Thicker wire: less resistance
  • Material (resistivity ρ)
    • Copper: low
    • Nichrome: high
    • Rubber, glass: very high

V = IR (1 Ω = 1 V A⁻¹). R = ρL/A, ρ in Ω m. G = 1/R (mho); σ = 1/ρ (mho m⁻¹).

Key takeaways: at constant temperature, current is proportional to potential difference. Resistance grows with length, falls with thickness and depends on the material through ρ. Conductance and conductivity are simply the reciprocals of resistance and resistivity.

Read the full lesson

Lesson 3

Resistors in series, in parallel and in combinations

Series and parallel circuits

  • Series
    • Same current in every resistor
    • Voltages add up
    • R_s more than the largest resistor
    • Smaller total current
    • One breaks, all stop
  • Parallel
    • Same voltage across every resistor
    • Currents add up
    • R_p less than the smallest resistor
    • Larger total current
    • Each works independently

Series: R_s = R₁ + R₂ + R₃ (n equal: nR). Parallel: 1/R_p = 1/R₁ + 1/R₂ + 1/R₃ (n equal: R/n).

Key takeaways: in series, the current is the same everywhere and the voltage is divided; in parallel, voltage is the same and current is divided. Adding resistors in series raises the total resistance; adding them in parallel lowers it.

Read the full lesson

Lesson 4

Heating effect of current and electric power

Choosing a material for the job
UseMaterialWhy
Heating element (iron, toaster, oven, heater, geyser)Nichrome, an alloy of nickel and chromiumHigh resistivity, high melting point, not easily oxidised
Fuse wire, in series in the circuitA material with a relatively low melting pointMelts when the current is too large and breaks the circuit, protecting appliances
Filament of a bulbTungstenVery high melting point, so it can glow white hot without melting

From work to heat and power

  1. W = VQ
  2. Q = It, so W = VIt
  3. Heat H = I²Rt Joule's law
  4. Power P = W/t = VI = I²R = V²/R

H = VIt = I²Rt (joule). P = VI = I²R = V²/R (watt). 1 kW = 1000 W; 1 hp = 746 W.

Key takeaways: heat grows with the square of the current, so doubling the current quadruples the heating. Nichrome heats, fuse wire melts to protect, tungsten glows. Power is voltage times current.

Read the full lesson

Lesson 5

Electrical energy, domestic circuits, safety and LEDs

1 kWh = 1000 W × 3600 s = 3.6 × 10⁶ J = 1 unit of electrical energy.

From the street to the appliance

  1. Supply from the distribution panel
  2. Main fuse on the live wire
  3. Electricity meter
  4. Main switch
  5. Separate parallel circuits 5 A circuit and 15 A circuit

Key takeaways: energy = power × time, and 1 unit = 1 kWh = 3.6 × 10⁶ J. Houses use parallel circuits with a fuse or MCB and an earth wire for safety. LEDs give the same light for far less energy.

Read the full lesson

Privacy · Terms · Refunds · Delivery