• Practice
  • About 14 min
  • 5 practice questions

Electric current, circuits and potential difference

Define electric current and the ampere, use I = Q/t, read circuit symbols, tell electron flow from conventional current, and define electric potential, potential difference and the volt with V = W/Q.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Define electric current and the ampere, and use I = Q/t.
  • Describe a closed circuit and recognise the main circuit components.
  • Explain the direction of conventional current and of electron flow.
  • Define electric potential, potential difference and the volt, and use V = W/Q.

Electricity runs our homes, schools, hospitals and industries. Behind every switch is the same idea: charges flowing through a conductor because something pushes them. This lesson sets up the words for that flow (current) and that push (potential difference).

Electric current

The movement of electric charges (electrons) through a conductor such as a copper wire is an electric current, much as water flows along a channel or air flows from high pressure to low pressure. Current I is the rate of flow of charge: if a net charge Q crosses any cross-section of a conductor in time t, then I = Q/t.

The SI unit of current is the ampere (A). One ampere flows when one coulomb of charge crosses a cross-section in one second: 1 A = 1 C/1 s. Current is measured with an ammeter, connected in series.

Worked example 1: current from charge and time

Question: 30 C of charge passes through a lamp in 1 minute. Find the current.

Working: t = 60 s. I = Q/t = 30 ÷ 60 = 0.5 A. Always change minutes to seconds first.

Worked example 2: counting electrons

Question: A current of 3.2 A flows for 1 s. How many electrons pass a point? (Charge of one electron = 1.6 × 10⁻¹⁹ C.)

Working: Q = It = 3.2 × 1 = 3.2 C. Number of electrons = Q/e = 3.2 ÷ (1.6 × 10⁻¹⁹) = 2 × 10¹⁹.

The electric circuit

An electric circuit is a closed conducting path, a network of components through which electrons can flow, made with wires joining an appliance to a source such as a battery. With a battery, a bulb and a switch: switch on, the circuit is closed and the bulb glows; switch off, the circuit is open and no current flows.

Electrons flow from the negative terminal of the battery through the circuit to the positive terminal. By convention, the direction of current is the direction in which positive charge would flow, which is opposite to the electron flow: from the positive terminal (higher potential) through the circuit to the negative terminal (lower potential).

Some circuit components and their uses
ComponentUse
ResistorFixes the size of the current in a circuit
Variable resistor (rheostat)Lets you select (vary) the current
AmmeterMeasures current
VoltmeterMeasures potential difference
GalvanometerDetects a current and its direction
DiodeUsed in electronic devices
Light emitting diode (LED)Used, for example, in seven segment displays
Ground (earth) connectionProtects components; a reference point for measuring potential

Electric potential and potential difference

Heat flows only when there is a temperature difference; charge flows in a conductor only when there is a difference in electric potential, from higher potential to lower potential.

  • Electric potential at a point: the work done in moving a unit positive charge from infinity to that point against the electric force.
  • Potential difference between two points: the work done in moving a unit positive charge from one point to the other against the electric force. If work W moves charge Q, then V = W/Q. It also equals the difference of the two potentials: V = V_A − V_B (when V_A is higher).

The SI unit of potential and potential difference is the volt (V). The potential difference between two points is 1 volt when 1 joule of work moves 1 coulomb of charge between them: 1 V = 1 J/C. It is measured with a voltmeter, connected in parallel across the two points.

Worked example 3: work done on a charge

Question: How much work is done in moving 4 C of charge across a potential difference of 12 V?

Working: W = QV = 4 × 12 = 48 J.

Two directions in one circuit

  • Electron flow
    • From negative terminal
    • Through the circuit
    • To positive terminal
  • Conventional current
    • From positive terminal (higher potential)
    • Through the circuit
    • To negative terminal (lower potential)

I = Q/t (1 A = 1 C s⁻¹). V = W/Q (1 V = 1 J C⁻¹). Conventional current flows from + to − outside the cell, opposite to the electrons.

Key takeaways: current is charge per second; potential difference is energy per unit charge. A circuit must be closed for current to flow, and the battery provides the potential difference that drives it.

Check your understanding

  1. 1. A charge of 90 C flows through a wire in 30 s. The current is

    1. 2700 A
    2. 0.33 A
    3. 3 A
    4. 60 A
    Show answer

    Answer: C. I = Q/t = 90 ÷ 30 = 3 A. Multiplying (2700) or dividing the wrong way (0.33) are common slips.

  2. 2. Outside the battery, conventional current flows

    1. from the positive terminal to the negative terminal
    2. from the negative terminal to the positive terminal
    3. in the same direction as the electrons
    4. in both directions at once
    Show answer

    Answer: A. By convention current is the direction of flow of positive charge: from + (higher potential) to − through the circuit, opposite to the electrons.

  3. 3. 60 J of work is done in moving 5 C of charge between two points. The potential difference is

    1. 300 V
    2. 0.083 V
    3. 65 V
    4. 12 V
    Show answer

    Answer: D. V = W/Q = 60 ÷ 5 = 12 V.

  4. 4. Which instrument only detects a current and its direction?

    1. Voltmeter
    2. Galvanometer
    3. Rheostat
    4. Fuse
    Show answer

    Answer: B. A galvanometer detects current and shows its direction. An ammeter measures current, a voltmeter measures potential difference and a rheostat varies the current.

  5. 5. Which component is used to vary (select) the current in a circuit?

    1. Rheostat
    2. Voltmeter
    3. LED
    4. Ground connection
    Show answer

    Answer: A. A rheostat is a variable resistor. Changing its resistance changes the current.

Privacy · Terms · Refunds · Delivery