• Practice
  • About 15 min
  • 5 practice questions

Heating effect of current and electric power

Derive Joule's law of heating H = I²Rt, explain heating elements, fuses and filaments, and calculate electric power with P = VI = I²R = V²/R, including the watt, kilowatt and horse power.

If something looks wrong, please tell us.

By the end of this lesson you can

  • Derive and state Joule's law of heating.
  • Explain why nichrome, fuse wire and tungsten are chosen for their jobs.
  • Calculate electric power with P = VI and its other forms.
  • Use the watt, kilowatt and horse power.

Touch the motor casing of a fan that has run for hours, or a bulb that has been on for a while, and it feels warm. Whenever current flows through a resistance, some electrical energy becomes heat. Sometimes that heat is wasted; in an iron or a heater it is the whole point.

Heating effect and Joule's law

A source keeps a current flowing by spending energy all the time. Part of it may do useful work and the rest becomes heat. The production of heat when current passes through a wire is the heating effect of current.

  1. A charge Q moves through a resistor R with potential difference V across it, in time t.
  2. Work done = VQ, and this energy is given out as heat: H = VQ.
  3. Since Q = It, H = VIt.
  4. Using V = IR, H = I²Rt: Joule's law of heating.

Joule's law of heating: the heat produced in a resistor is directly proportional to (1) the square of the current, (2) the resistance and (3) the time for which the current flows. Heat is in joules when I is in amperes, R in ohms and t in seconds.

Worked example 1: heat from a resistor

Question: A current of 2 A flows through a 50 Ω resistor for 10 minutes. Find the heat produced.

Working: t = 10 × 60 = 600 s. H = I²Rt = 2² × 50 × 600 = 4 × 50 × 600 = 120 000 J (120 kJ). If the current were doubled to 4 A, the heat would be four times as much.

Uses of the heating effect

Choosing a material for the job
UseMaterialWhy
Heating element (iron, toaster, oven, heater, geyser)Nichrome, an alloy of nickel and chromiumHigh resistivity, high melting point, not easily oxidised
Fuse wire, in series in the circuitA material with a relatively low melting pointMelts when the current is too large and breaks the circuit, protecting appliances
Filament of a bulbTungstenVery high melting point, so it can glow white hot without melting

Electric power

Electric power is the rate at which electrical energy is used, that is, converted into other forms. With W = VIt, power P = W/t = VI. Using V = IR, this can also be written P = I²R or P = V²/R.

The SI unit is the watt (W): 1 watt is the power used when a device runs on 1 volt and carries 1 ampere (1 W = 1 V × 1 A). A larger unit is the kilowatt (kW) = 1000 W. The horse power (hp), a unit of the foot-pound-second system, is sometimes used for motors: 1 hp = 746 W.

Worked example 2: rating of an electric kettle

Question: A kettle is rated 1100 W, 220 V. Find the current it draws and its resistance.

Working: I = P/V = 1100 ÷ 220 = 5 A. R = V/I = 220 ÷ 5 = 44 Ω. Check with R = V²/P = 48 400 ÷ 1100 = 44 Ω.

Worked example 3: two bulbs on the same supply

Question: Compare the resistances of a 100 W and a 25 W bulb, both rated for 220 V.

Working: R = V²/P. 100 W bulb: 48 400 ÷ 100 = 484 Ω. 25 W bulb: 48 400 ÷ 25 = 1936 Ω. On the same voltage, the lower-power bulb has the higher resistance.

Worked example 4: horse power

Question: A water pump motor is rated 2 hp. What is its power in watts and kilowatts?

Working: P = 2 × 746 = 1492 W ≈ 1.49 kW.

From work to heat and power

  1. W = VQ
  2. Q = It, so W = VIt
  3. Heat H = I²Rt Joule's law
  4. Power P = W/t = VI = I²R = V²/R

H = VIt = I²Rt (joule). P = VI = I²R = V²/R (watt). 1 kW = 1000 W; 1 hp = 746 W.

Key takeaways: heat grows with the square of the current, so doubling the current quadruples the heating. Nichrome heats, fuse wire melts to protect, tungsten glows. Power is voltage times current.

Check your understanding

  1. 1. A current of 3 A flows through a 10 Ω resistor for 20 s. The heat produced is

    1. 600 J
    2. 60 J
    3. 1800 J
    4. 180 J
    Show answer

    Answer: C. H = I²Rt = 3² × 10 × 20 = 9 × 200 = 1800 J. Forgetting to square the current gives the wrong 600 J.

  2. 2. If the current through a heater is doubled (resistance unchanged), the heat produced in the same time becomes

    1. four times
    2. double
    3. half
    4. the same
    Show answer

    Answer: A. H ∝ I². Doubling I multiplies the heat by 2² = 4.

  3. 3. Nichrome is used as the heating element in an electric iron because it

    1. has a very low resistivity
    2. melts easily
    3. is a good insulator
    4. has high resistivity and a high melting point and does not oxidise easily
    Show answer

    Answer: D. The Tamil Nadu textbook gives three reasons: high resistivity, high melting point and resistance to oxidation. A low melting point is wanted in a fuse, not a heater.

  4. 4. An appliance draws 0.5 A from a 220 V supply. Its power is

    1. 440 W
    2. 110 W
    3. 220.5 W
    4. 0.0023 W
    Show answer

    Answer: B. P = VI = 220 × 0.5 = 110 W.

  5. 5. A fuse wire protects a circuit because it

    1. has a low melting point and is connected in series, so it melts on excess current
    2. has a very high melting point
    3. is connected in parallel with the appliance
    4. stores extra current
    Show answer

    Answer: A. The fuse is in series. When the current becomes too large, Joule heating melts the low-melting wire and the circuit is broken.

Privacy · Terms · Refunds · Delivery